NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certiﬁ ed technician. Logos and trademarks used here in

are the properties of their respective owners.

WARNING

all of the guides in this compilation.

Need help?

Do you have a question about the maestro Rr and is the answer not in the manual?

Questions and answers

Summary of Contents for iDataLink maestro Rr

Page 1 Print only the pages for your vehicle using the advanced options in the Print menu. Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation.
Page 2 ToyoTa 4 RunneR WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 3 ToyoTa 4 RunneR WiTh JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 4 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 5 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 6 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 7 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 8 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 9 ToyoTa 4 RunneR WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 10 ToyoTa 4 RunneR WiThouT JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 11 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 12 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 13 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 14 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 15 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 16 2019-2020 ToyoTa avaLon WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 17 ToyoTa avaLon WiTh JBL 2019-2020 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 18 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 19 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 20 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 21 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 22 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 23 2019-2020 ToyoTa avaLon WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 24 ToyoTa avaLon WiThouT JBL 2019-2020 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 25 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 26 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 27 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 28 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 29 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 30 ToyoTa C-hR WiTh CaRPLay WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 31 ToyoTa C-hR WiTh CaRPLay WiTh JBL 2018 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 32 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 33 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 34 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 35 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 36 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 37 ToyoTa C-hR WiTh CaRPLay WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 38 ToyoTa C-hR WiTh CaRPLay WiThouT JBL 2018 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 39 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 40 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 41 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 42 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 43 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 44 2019-2021 ToyoTa C-hR WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 45 ToyoTa C-hR WiTh JBL 2019-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 46 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 47 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 48 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 49 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 50 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 51 2019-2021 ToyoTa C-hR WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 52 ToyoTa C-hR WiThouT JBL 2019-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 53 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 54 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 55 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 56 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 57 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 58 2018-2021 ToyoTa CamRy WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 59 ToyoTa CamRy WiTh JBL 2018-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 60 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 61 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 62 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 63 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 64 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 65 2018-2021 ToyoTa CamRy WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 66 ToyoTa CamRy WiThouT JBL 2018-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 67 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 68 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 69 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 70 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 71 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 72 ToyoTa CoRoLLa haTChBaCk WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 73 ToyoTa CoRoLLa haTChBaCk WiTh JBL 2019-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 74 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 75 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 76 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 77 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 78 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 79 ToyoTa CoRoLLa haTChBaCk WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 80 ToyoTa CoRoLLa haTChBaCk WiThouT JBL 2019-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 81 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 82 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 83 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 84 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 85 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 86 2020-2021 ToyoTa CoRoLLa WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 87 ToyoTa CoRoLLa WiTh JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 88 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 89 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 90 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 91 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 92 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 93 2020-2021 ToyoTa CoRoLLa WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 94 ToyoTa CoRoLLa WiThouT JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 95 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 96 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 97 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 98 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 99 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 100 2020-2021 ToyoTa highLandeR WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 101 ToyoTa highLandeR WiTh JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 102 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 103 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 104 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 105 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 106 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 107 2020-2021 ToyoTa highLandeR WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 108 ToyoTa highLandeR WiThouT JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 109 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 110 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 111 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 112 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 113 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 114 2019-2021 ToyoTa Rav4 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 115 ToyoTa Rav4 WiTh JBL 2019-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 116 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 117 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 118 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 119 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 120 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 121 2019-2021 ToyoTa Rav4 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 122 ToyoTa Rav4 WiThouT JBL 2019-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 123 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 124 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 125 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 126 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 127 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 128 2020-2021 ToyoTa Sequoia WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 129 ToyoTa Sequoia WiTh JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 130 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 131 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 132 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 133 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 134 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 135 2020-2021 ToyoTa Sequoia WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 136 ToyoTa Sequoia WiThouT JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 137 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 138 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 139 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 140 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 141 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 142 2018-2020 ToyoTa Sienna WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 143 ToyoTa Sienna WiTh JBL 2018-2020 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 144 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 145 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 146 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 147 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 148 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 149 2018-2020 ToyoTa Sienna WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 150 ToyoTa Sienna WiThouT JBL 2018-2020 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 151 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 152 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 153 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 154 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 155 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 156 2020-2021 ToyoTa TaComa WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 157 ToyoTa TaComa WiTh JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 158 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 159 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 160 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 161 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 162 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 163 2020-2021 ToyoTa TaComa WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 164 ToyoTa TaComa WiThouT JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 165 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 166 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 167 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 168 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 169 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 170 2020-2021 ToyoTa TundRa WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 171 ToyoTa TundRa WiTh JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 172 Camera 1 on the radio. This is the only camera input that allows camera control through STEP 4 the touchscreen • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN...
Page 173 CONTROL CABLE 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 174 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 175 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 176 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 177 ToyoTa TundRa WiTh non-JBL amP RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 178 ToyoTa TundRa WiTh non-JBL amP 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 179 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 180 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 181 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 182 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 183 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 184 2020-2021 ToyoTa TundRa WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRR-TO3 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 185 ToyoTa TundRa WiThouT JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 186 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera • Connect all the harnesses to the Maestro RR module then system, plug the camera into Camera 1 on the radio. This is test your installation.
Page 187 CONTROL CABLE CONTROL CABLE WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN 4-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED DATA CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 188 Wire Color on Adapter Kenwood Radio Wire Description Refer to camera/radio Green/Red manual Refer to camera/radio Green/White manual Connect if no iDatalink Steering Wheel Controls (DATA) Blue/Yellow 4-pin port on radio ACC-HU-KEN2 Polarity Wire Color on Adapter Kenwood Radio Wire Description...
Page 189 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03h-AS-IG-EN maestro.idatalink.com...
Page 190 Maestro purple/white wire, to the radio's reverse trigger input. (Maestro purple/white wire is not used). MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).
Page 191 Print only the pages for your vehicle using the advanced options in the Print menu. Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation.
Page 192 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 193 ToyoTa 4 RunneR WiTh JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 194 Camera 1 on the radio. This is into the W/R port. the only camera input that allows camera control through the touchscreen STEP 4 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 195 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 196 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 197 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 198 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 199 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 200 ToyoTa 4 RunneR WiThouT JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 201 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 202 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 203 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 204 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 205 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 206 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 207 ToyoTa avaLon WiTh JBL 2019-2020 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 208 Camera 1 on the radio. This is into the W/R port. the only camera input that allows camera control through the touchscreen STEP 4 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 209 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 210 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 211 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 212 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 213 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 214 ToyoTa avaLon WiThouT JBL 2019-2020 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 215 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 216 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 217 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 218 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 219 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 220 WiTh CaRPLay WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 221 ToyoTa C-hR WiTh CaRPLay WiTh JBL 2018 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 222 Camera 1 on the radio. This is into the W/R port. the only camera input that allows camera control through the touchscreen STEP 4 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 223 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 224 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 225 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 226 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 227 WiTh CaRPLay WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 228 ToyoTa C-hR WiTh CaRPLay WiThouT JBL 2018 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 229 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 230 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 231 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 232 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 233 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 234 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 235 ToyoTa C-hR WiTh JBL 2019-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 236 Camera 1 on the radio. This is into the W/R port. the only camera input that allows camera control through the touchscreen STEP 4 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 237 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 238 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 239 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 240 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 241 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 242 ToyoTa C-hR WiThouT JBL 2019-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 243 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 244 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 245 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 246 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 247 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 248 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 249 ToyoTa CamRy WiTh JBL 2018-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 250 Camera 1 on the radio. This is into the W/R port. the only camera input that allows camera control through the touchscreen STEP 4 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 251 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 252 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 253 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 254 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 255 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 256 ToyoTa CamRy WiThouT JBL 2018-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 257 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 258 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 259 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 260 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 261 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 262 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 263 ToyoTa CoRoLLa haTChBaCk WiTh JBL 2019-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 264 Camera 1 on the radio. This is into the W/R port. the only camera input that allows camera control through the touchscreen STEP 4 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 265 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 266 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 267 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 268 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 269 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 270 ToyoTa CoRoLLa haTChBaCk WiThouT JBL 2019-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 271 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 272 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 273 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 274 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 275 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 276 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 277 ToyoTa CoRoLLa WiTh JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 278 Camera 1 on the radio. This is into the W/R port. the only camera input that allows camera control through the touchscreen STEP 4 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 279 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 280 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 281 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 282 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 283 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 284 ToyoTa CoRoLLa WiThouT JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 285 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 286 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 287 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 288 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 289 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 290 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 291 ToyoTa highLandeR WiTh JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 292 Camera 1 on the radio. This is into the W/R port. the only camera input that allows camera control through the touchscreen STEP 4 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 293 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 294 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 295 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 296 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 297 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 298 ToyoTa highLandeR WiThouT JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 299 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 300 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 301 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 302 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 303 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 304 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 305 ToyoTa Rav4 WiTh JBL 2019-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 306 Camera 1 on the radio. This is into the W/R port. the only camera input that allows camera control through the touchscreen STEP 4 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 307 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 308 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 309 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 310 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 311 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 312 ToyoTa Rav4 WiThouT JBL 2019-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 313 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 314 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 315 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 316 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 317 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 318 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 319 ToyoTa Sequoia WiTh JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 320 Camera 1 on the radio. This is into the W/R port. the only camera input that allows camera control through the touchscreen STEP 4 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 321 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 322 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 323 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 324 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 325 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 326 ToyoTa Sequoia WiThouT JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 327 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 328 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 329 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 330 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 331 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 332 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 333 ToyoTa Sienna WiTh JBL 2018-2020 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 334 • Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 335 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 5 STEP 3 OBDII CONNECTOR 2-PIN MAESTRO RR MODULE 18 PIN AMP TURN ON AMP TURN ON 10 PIN HHR-TO3 T-HARNESS NOT REQUIRED STEERING WHEEL 10 PIN CONTROL CABLE 3 PIN...
Page 336 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 337 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 338 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 339 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 340 ToyoTa Sienna WiThouT JBL 2018-2020 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 341 Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 342 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 5 STEP 3 OBDII CONNECTOR 2-PIN MAESTRO RR MODULE 18 PIN AMP TURN ON AMP TURN ON 10 PIN HHR-TO3 T-HARNESS NOT REQUIRED STEERING WHEEL 10 PIN CONTROL CABLE 3 PIN...
Page 343 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 344 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 345 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 346 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 347 ToyoTa TaComa WiTh JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 348 Camera 1 on the radio. This is into the W/R port. the only camera input that allows camera control through the touchscreen STEP 4 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 349 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 350 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 351 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 352 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 353 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 354 ToyoTa TaComa WiThouT JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 355 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 356 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 357 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 358 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 359 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 360 WiTh JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 361 ToyoTa TundRa WiTh JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 362 Camera 1 on the radio. This is into the W/R port. the only camera input that allows camera control through the touchscreen STEP 4 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 363 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 364 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 365 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 366 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 367 WiTh non-JBL amP RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 368 ToyoTa TundRa WiTh non-JBL amP 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 369 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 370 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 371 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 372 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 373 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Page 374 WiThouT JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro HRR-TO3 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 375 ToyoTa TundRa WiThouT JBL 2020-2021 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features.
Page 376 Camera 1 on the radio. This is • Connect all the harnesses to the Maestro RR module then the only camera input that allows camera control through test your installation.
Page 377 STEP 2 FACTORY RADIO HARNESS 10-PIN WIRES FROM VEHICLE 28-PIN 30-PIN STEP 4 2-PIN AMP TURN ON AMP TURN ON MAESTRO RR MODULE 18 PIN HHR-TO3 T-HARNESS 10 PIN NOT REQUIRED STEERING WHEEL CONTROL CABLE 10 PIN 3 PIN AUDIO CABLE Automotive Data Solutions Inc.
Page 378 Wire Color on Adapter Kenwood Radio Wire Description E-Brake LtGreen LtGreen Reverse Light* Purple/White Purple/White Steering Wheel Controls (DATA) Blue/Yellow * Reverse light wire: Only connect to radio or module damage will occur. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 379 Turns off after one minute: Normal operation. • • Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-TOY03H-DS-IG-EN maestro.idatalink.com...
Page 380 The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

iDataLink maestro Rr Install Manual

Quick Links

Need help?

Questions and answers

Related Manuals for iDataLink maestro Rr

Summary of Contents for iDataLink maestro Rr