NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certiﬁ ed technician. Logos and trademarks used here in

are the properties of their respective owners.

WARNING

all of the guides in this compilation.

Need help?

Do you have a question about the maestro Rr and is the answer not in the manual?

Questions and answers

Summary of Contents for iDataLink maestro Rr

Page 1 Print only the pages for your vehicle using the advanced options in the Print menu. Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation.
Page 2 ToyoTa 4 RunneR WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 3 ToyoTa 4 RunneR WiTh JBL 2014-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 4 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 5 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE STEP 3 WIRES FROM VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 6 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 7 ToyoTa 4 RunneR WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 8 ToyoTa 4 RunneR WiThouT JBL 2014-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 9 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 10 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 11 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 12 2015-2019 ToyoTa avaLon WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 13 ToyoTa avaLon WiTh JBL 2015-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 14 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 15 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE STEP 3 WIRES FROM VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 16 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 17 ToyoTa avaLon WiTh nav WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 18 ToyoTa avaLon WiTh nav WiTh JBL 2013-2014 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 19 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 20 WIRES FROM BLUE/YELLOW BLUE/YELLOW BLACK BLACK VEHICLE BLACK BLACK STEP 3 FACTORY RADIO HARNESS STEP 6 STEP 4 MAESTRO RR MODULE OBDII CONNECTOR N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN...
Page 21 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 22 ToyoTa avaLon WiTh nav WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 23 ToyoTa avaLon WiTh nav WiThouT JBL 2013-2014 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 24 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 25 WIRES AS SHOWN. YELLOW WHITE BLACK WIRES FROM BLUE/YELLOW BLACK VEHICLE BLACK STEP 3 FACTORY RADIO HARNESS STEP 6 MAESTRO RR MODULE STEP 4 OBDII CONNECTOR N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 26 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 27 2015-2019 ToyoTa avaLon WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 28 ToyoTa avaLon WiThouT JBL 2015-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 29 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 30 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 31 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 32 ToyoTa C-hR WiThouT appLe CaRpLay oR andRoid auTo RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 33 ToyoTa C-hR WiThouT appLe CaRpLay oR andRoid auTo 2018 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 34 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 5 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 35 STEERING WHEEL FACTORY RADIO HARNESS CONTROL CABLE WIRES FROM VEHICLE STEP 3 OBDII CONNECTOR STEP 5 N.C. N.C. MAESTRO RR MODULE TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE BACKUP CAM BACKUP CAM Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN...
Page 36 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 37 ToyoTa CamRy WiTh FaCToRy 6.1 inCh SCReen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 38 ToyoTa CamRy WiTh FaCToRy 6.1 inCh SCReen 2012-2014 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 39 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 40 WIRES AS SHOWN. YELLOW WHITE BLACK WIRES FROM BLUE/YELLOW BLACK VEHICLE BLACK STEP 3 FACTORY RADIO HARNESS STEP 6 MAESTRO RR MODULE STEP 4 OBDII CONNECTOR N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 41 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 42 ToyoTa CamRy WiTh FaCToRy 6.1 inCh SCReen and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 43 ToyoTa CamRy WiTh FaCToRy 6.1 inCh SCReen and JBL 2012-2014 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 44 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 45 WIRES FROM BLUE/YELLOW BLUE/YELLOW BLACK BLACK VEHICLE BLACK BLACK STEP 3 FACTORY RADIO HARNESS STEP 6 STEP 4 MAESTRO RR MODULE OBDII CONNECTOR N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN...
Page 46 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 47 ToyoTa CamRy WiTh FaCToRy SCReen and hdd and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 48 ToyoTa CamRy WiTh FaCToRy SCReen and hdd and JBL 2012-2014 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 49 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 50 WIRES FROM BLUE/YELLOW BLUE/YELLOW BLACK BLACK VEHICLE BLACK BLACK STEP 3 FACTORY RADIO HARNESS STEP 6 STEP 4 MAESTRO RR MODULE OBDII CONNECTOR N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN...
Page 51 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 52 2015-2017 ToyoTa CamRy WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 53 ToyoTa CamRy WiTh JBL 2015-2017 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 54 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 55 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE STEP 3 WIRES FROM VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 56 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 57 2015-2017 ToyoTa CamRy WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 58 ToyoTa CamRy WiThouT JBL 2015-2017 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 59 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 60 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 61 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 62 ToyoTa CoRoLLa WiTh FaCToRy 6.1 inCh SCReen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 63 ToyoTa CoRoLLa WiTh FaCToRy 6.1 inCh SCReen 2014-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 64 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 65 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 66 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 67 2014-2019 ToyoTa highLandeR WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 68 ToyoTa highLandeR WiTh JBL 2014-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 69 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 70 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE STEP 3 WIRES FROM VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 71 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 72 2014-2019 ToyoTa highLandeR WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 73 ToyoTa highLandeR WiThouT JBL 2014-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 74 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 75 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 76 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 77 2016-2019 ToyoTa pRiuS BaSe RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here...
Page 78 ToyoTa pRiuS BaSe 2016-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 79 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 80 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 81 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 82 ToyoTa pRiuS C WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 83 ToyoTa pRiuS C WiTh JBL 2015-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 84 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 85 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE STEP 3 WIRES FROM VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 86 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 87 ToyoTa pRiuS C WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 88 ToyoTa pRiuS C WiThouT JBL 2012-2014 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 89 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 90 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 91 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 92 ToyoTa pRiuS C WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 93 ToyoTa pRiuS C WiThouT JBL 2015-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 94 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 95 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 96 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 97 ToyoTa pRiuS v WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 98 ToyoTa pRiuS v WiTh JBL 2012-2014 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 99 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 100 WIRES FROM BLUE/YELLOW BLUE/YELLOW WHITE VEHICLE BLACK BLACK STEP 3 FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS DATA NOT REQUIRED CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 101 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 102 ToyoTa pRiuS v WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 103 ToyoTa pRiuS v WiTh JBL 2015-2017 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 104 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 105 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE STEP 3 WIRES FROM VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 106 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 107 ToyoTa pRiuS v WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 108 ToyoTa pRiuS v WiThouT JBL 2012-2014 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 109 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 110 WIRES AS SHOWN. YELLOW WIRES FROM BLACK BLACK VEHICLE BLUE/YELLOW WHITE BLACK STEP 3 FACTORY RADIO HARNESS STEP 6 MAESTRO RR MODULE STEP 4 OBDII CONNECTOR N.C. N.C. TO2 T-HARNESS DATA NOT REQUIRED CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 111 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 112 ToyoTa pRiuS v WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 113 ToyoTa pRiuS v WiThouT JBL 2015-2017 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 114 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 115 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 116 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 117 2012-2014 ToyoTa pRiuS WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 118 ToyoTa pRiuS WiTh JBL 2012-2014 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 119 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 120 WIRES FROM BLUE/YELLOW BLUE/YELLOW WHITE VEHICLE BLACK BLACK STEP 3 FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS DATA NOT REQUIRED CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 121 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 122 2015-2019 ToyoTa pRiuS WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 123 ToyoTa pRiuS WiTh JBL 2015-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 124 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 125 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE STEP 3 WIRES FROM VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 126 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 127 ToyoTa pRiuS WiTh nav WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 128 ToyoTa pRiuS WiTh nav WiThouT JBL 2012-2014 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 129 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 130 WIRES AS SHOWN. YELLOW WIRES FROM BLACK BLACK VEHICLE BLUE/YELLOW WHITE BLACK STEP 3 FACTORY RADIO HARNESS STEP 6 MAESTRO RR MODULE STEP 4 OBDII CONNECTOR N.C. N.C. TO2 T-HARNESS DATA NOT REQUIRED CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 131 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 132 ToyoTa pRiuS WiTh nav WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 133 ToyoTa pRiuS WiTh nav WiThouT JBL 2015-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 134 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 135 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 136 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 137 ToyoTa Rav 4 WiTh FaCToRy 6.1 inCh SCReen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 138 ToyoTa Rav 4 WiTh FaCToRy 6.1 inCh SCReen 2013-2018 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 139 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 140 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 141 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 142 ToyoTa Rav 4 WiTh FaCToRy 6.1 inCh SCReen and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 143 ToyoTa Rav 4 WiTh FaCToRy 6.1 inCh SCReen and JBL 2013-2018 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 144 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 145 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE STEP 3 WIRES FROM VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 146 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 147 2014-2019 ToyoTa Sequoia WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 148 ToyoTa Sequoia WiTh JBL 2014-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 149 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 150 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE STEP 3 WIRES FROM VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 151 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 152 2015-2019 ToyoTa Sienna WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 153 ToyoTa Sienna WiTh JBL 2015-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 154 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 155 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS DATA NOT REQUIRED CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 156 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 157 2015-2019 ToyoTa Sienna WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 158 ToyoTa Sienna WiThouT JBL 2015-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 159 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 160 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 161 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 162 2016-2019 ToyoTa TaComa WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 163 ToyoTa TaComa WiTh JBL 2016-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 164 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 165 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE STEP 3 WIRES FROM VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 166 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 167 2016-2019 ToyoTa TaComa WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 168 ToyoTa TaComa WiThouT JBL 2016-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 169 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 170 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 171 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 172 2014-2019 ToyoTa TundRa WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 173 ToyoTa TundRa WiTh JBL 2014-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 174 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 175 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE STEP 3 WIRES FROM VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 176 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 177 ToyoTa TundRa WiTh non-JBL amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 178 ToyoTa TundRa WiTh non-JBL amp 2014-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 179 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 180 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 181 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 182 2014-2019 ToyoTa TundRa WiThouT amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 183 ToyoTa TundRa WiThouT amp 2014-2019 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 184 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 185 STEERING WHEEL CONNECT IF EQUIPPED CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 186 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 187 2015-2016 ToyoTa venza WiTh JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 188 ToyoTa venza WiTh JBL 2015-2016 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 189 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 190 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS DATA NOT REQUIRED CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 191 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 192 ToyoTa venza WiTh JBL and nav RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 193 ToyoTa venza WiTh JBL and nav 2013-2014 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 194 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 195 BLUE/YELLOW BLACK BLACK WIRES FROM BLACK BLACK VEHICLE STEP 3 FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS NOT REQUIRED DATA CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 196 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).
Page 197 2015-2016 ToyoTa venza WiThouT JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Page 198 ToyoTa venza WiThouT JBL 2015-2016 WELCOME TABLE OF CONTENTS Installation Instructions Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram now a few simple steps away from enjoying your new car radio with Troubleshooting Table enhanced features.
Page 199 • Connect the auxiliary RCA cables into the aftermarket radio (if equipped). • Plug the steering wheel control cable into the aftermarket radio. STEP 6 • Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 200 CONNECT IF EQUIPPED STEERING WHEEL CONTROL CABLE WIRES FROM STEP 3 VEHICLE FACTORY RADIO HARNESS STEP 6 STEP 4 OBDII CONNECTOR MAESTRO RR MODULE N.C. N.C. TO2 T-HARNESS DATA NOT REQUIRED CABLE AUDIO CABLE Automotive Data Solutions Inc. © 2021 ADS-RR(SR)-TOY02-DS-IG-EN maestro.idatalink.com...
Page 201 There is no ﬁ rmware on the module; ﬂ ash the RR module. RED ONCE MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds).

iDataLink maestro Rr How To Use Manual

Quick Links

Need help?

Questions and answers

Related Manuals for iDataLink maestro Rr

Summary of Contents for iDataLink maestro Rr