Kenwood KDC-MP538U Service Manual page 14

KDC-MP538U/MP6039/MP6539U/
W6041U/W6141UY/W6541U/W6641UY/X592
Table 1 - Version & Service information display mode
[1] Key pressed briefl y: Version is displayed
key (Display) C0724WK__SYS1.23
(Remote (Display) STYPE: xx_PAN1.11
controller) (Display) PTYPE: x__
∗1 STYPE indicates system μ-com destination, and
PTYPE indicates panel μ-com destination, and
show real-time condition of the destination termi-
nal
[2] Key pressed briefl y: Serial No. is displayed (8 digits)
key (Display) SNo_××××××××
(Remote
controller)
[AM]
[3] Key pressed briefl y: Power ON time is displayed.
key
key (Display) PonTim_0H××_ (00~50 is displayed for "xx".
(Remote
controller)
↑
[4] Key pressed briefl y: CD operation time is displayed.
key (Display) CDTim_0H××_ (00~50 is displayed for "xx".
(Remote
↓
controller)
[FM]
key
[5] Key pressed briefl y: Number of CD EJECT times is
key displayed.
(Remote (Display) EjeCnt_×××××
controller)
[6] Key pressed briefl y: Illumination color change (In
key this mode, [
(Remote color.)
controller) White (R255/G255/B255) → Red (R255/G0/B0) →
Green (R0/G255/B0) → Blue (R0/G0/B255) → White
(R255/G255/B255) → Red (R255/G0/B0) → ...
(Display) Illumi_Color
[ ] key Key pressed briefl y: Invalid
Press and hold: To clear the service information that
is being displayed. (Press and hold for 2 seconds
while each service information is displayed.)
[FNC] key Key pressed briefl y: Version & Service information
display mode OFF
14
TEST MODE
When less than 1 hour,
display by increment of 10
minutes.)
××××× (00001-10922 is displayed
for "xxxxxx".)
MAX 10922 (hours)
When less than 1 hour,
display by increment of 10
minutes.)
××××× (00001-10922 is displayed
for "xxxxxx".)
MAX 10922 (hours)
MAX 65535 (times)
] / [ ] key can be used to change
∗ Except KDC-MP6039
Table 2 - CD information display mode
I2C communication condition and CD mechanism error log
display
(Display) I2C_ ____________
(Display) ERR_1- , 2- , 3-
∗ "OK" or "NG" is displayed for "
code is displayed for " / ".
[AM]
CD loading error log display
key
(Display) Load_Error____
(Display) __(1) xx__ (2) xx
↑
(Number of times is displayed for "xx".)
CD ejection error log display
(Display) Eject_Error___
(Display) __(1) xx__ (2) xx
(Display) __(3) xx__ (4) xx
(Number of times is displayed for "xx".)
CD time code error count data display (missing counts)
↓
(Display) Count_Lose
(Display) __CDDA_: xx
[FM]
(Display) __CDROM: xx
key
(Number of times is displayed for "xx".)
CD time code error count data display (count not updated)
(Display) Count_Stay
(Display) __CDDA_: xx
(Display) __CDROM: xx
(Number of times is displayed for "xx".)
[ ] Key pressed briefl y: CD information display mode OFF
key Press and hold: To clear entire CD information (Press and
hold for 2 seconds)
● Initializing AUDIO-related setting value
Press the [ ] key briefl y in the STANDBY source to reset
the AUDIO setting value to the test mode default value.
● Other
• When Power ON, do not display "CODE_NG", "CODE_
OFF", and "CODE_ON".
• When the source is STANDBY, press and hold the [AUTO]
or [TI] keys for 1 second to switch the PREOUT between
Rear and Sub Woofer (Rear↔Sub Woofer).
• When started in the test mode, duration of prohibiting
LINE MUTE shall be changed from 10 seconds to 1 sec-
ond.
• When in the test mode, when DC offset error detection
is run, the detection information is not written into the
E2PROM.
• When in the test mode, even if the specified time has
passed, back-up memory items are not written into
E2PROM.
DEMO mode shall not be operated while in the test
mode, Backup/Installer Memory & CD Mechanism Infor-
". / "—" or the error
MAX 99 (times)
MAX 99 (times)
MAX 99 (times)
MAX 99 (times)