Kenwood KDC-MP538U Service Manual page 12

KDC-MP538U/MP6039/MP6539U/
W6041U/W6141UY/W6541U/W6641UY/X592
● AUDIO adjust mode
• Press the [AUD] key briefl y to enter the audio adjustment
mode.
• Press the remote control [∗] key and [AUD] key to enter
the audio adjustment mode.
• Both AUDIO FUNCTION MODE and SETUP MODE ad-
justment items are included.
• By pressing [AUD] and [FM] key briefl y, switch the item to
be adjusted in the following order. (Only in forward rota-
tion)
The default item shall be Fader, and then the item
is forwarded in the following order: Balance→Bass
Level→Middle Level→Treble Level→HPF Front→HPF
Rear→LPF Sub Woofer (thereafter arbitrary).
• Continuous forwarding by remote control is prohibited.
• Fader is adjusted by the VOL knob and [
in 3 steps: R15↔0↔F15. (Default value: 0)
• Balance is adjusted by the VOL knob and [
keys in 3 steps: L15↔0↔R15. (Default value: 0)
• Bass/Middle/Treble Level are adjusted by the VOL knob
and [ ] / [ ] keys in 3 steps: -8↔0↔8. (Default value:
0)
• HPF Front / Rear is adjusted by the VOL knob and [
/ [ ] keys in 2 steps: Through↔220Hz. (Default value:
Through)
• LPF Sub Woofer is adjusted by the VOL knob and [
/ [ ] keys in 2 steps: 50Hz ↔Through. (Default value:
Through)
• Sub Woofer Phase is adjusted by the VOL knob and [
/ [ ] keys in 2 steps: Reverse↔Normal. (Default value:
Normal)
• Volume Offset (other than the internal AUX) is adjusted
by the VOL knob and [
(Default value: 0)
• Volume Offset (the internal AUX) is adjusted by the VOL
knob and [ ] / [
value: 0)
• Loudness ON/OFF is adjusted by the VOL knob and [
/ [ ] keys in 2 steps: OFF↔ON. (Default value: OFF)
• Dual Zone ON / OFF is adjusted by the VOL knob and
[ ] / [ ] keys in 2 steps: OFF↔ON. (Default value:
OFF)
• Bass f / Bass Q / Bass EXT / Middle f / Middle Q / Treble
f are not displayed in the audio adjustment menu.
• SYSTEM Q (dB EQ) curve selection is not displayed in
the audio adjustment menu.
12
] / [
] / [ ] keys in 2 steps: -8↔0.
] keys in 3 steps: -8↔0↔+8. (Default
TEST MODE
● MENU
• Press the [FNC] key briefly to make the multi-function
display and press the [ ] key briefl y to enter the MENU.
• Press the remote control [DNPP/SBF] key and the
[DIRECT] key to enter the MENU.
• Continuous forwarding by remote control is prohibited.
• The initial item in TUNER source MENU source during
the Test mode shall be selectable between Seek ON and
OFF. (European model)
• Only in the Test mode, it shall be made possible to show
"ROM Write Mode" and "ROM Read Mode" items in the
STANDBY source MENU to allow the ROM data transfer
process.
● ROM data transfer
] keys
This function is used to transfer E2PROM data (installer
memory) inside of the front-end to mother E2PROM of
] / [ ]
the backup, and to transfer the data back from the moth-
er E2PROM to the E2PROM of the front-end.
How to transfer ROM data
q Enter the Test mode (All lights go on).
]
w Press [FNC] key briefl y while all lights are on to enter
in the Menu mode.
e Select "ROM Read Mode (Front-end→Mother)" or
]
"ROM Write Mode (Mother→Front end)", and press
and hold [ ] key for one second to turn Mode ON.
Operation
]
Start resetting by
pressing "[FNC]
key + [EJECT]
key"
Press [FNC] key
to select [Menu]
mode.
(In the above
]
ROM Read Mode)
Press and hold
[ ] key (for one
second) to select
Yes.
(In the above
ROM Write Mode)
Press and hold
[ ] key (for one
second) to select
Yes.
Display Description
All lights ON Test mode ON
Front-end→Mother
"ROM_Read_Mode"
Process to transfer data
Mother→Front-end
"ROM_Write_Mode"
Process to transfer data
Front-end→Mother
"ROM_Reading..."
ROM data transfer in progress
Front-end→Mother
"ROM_Read_OK"
ROM data transfer OK
Front-end→Mother
"ROM_Read_NG"
ROM data transfer NG
Mother→Front-end
"ROM_Writing..."
ROM data transfer in progress
Mother→Front-end
"ROM_Write_OK"
ROM data transfer OK
Mother→Front-end
"ROM_Write_NG"
ROM data transfer NG