KDC-MP5028/MP528 /W6031/W6031Y BLOCK DIAGRAM CD PLAYER UNIT (X32-5740) MOTHER BOARD PICKUP A3.3V REG RF AMP SERVO PROCESSOR L-ch R-ch MP3 DECODER A.GND WMA DECODER D.OUT AAC DECODER MRST 1Mbit SRAM MSTOP VREF DATA FO COIL D.GND MUTE L CLOCK MICRO MUTE R 16.934MHz...
Page 4
KDC-MP5028/MP528 /W6031/W6031Y COMPONENTS DESCRIPTION SWITCH UNIT (X16-2920-11/3142-70) Ref. No. Application / Function Operation / Condition / Compatibility VFD Driver Remote Control IC The power supply for IC2 is turned on when Q1’s base level goes “L”. Q2,Q3 FL+ SW The power supply for filament is turned on when Q3’s base level goes “H”.
Page 5
KDC-MP5028/MP528 /W6031/W6031Y COMPONENTS DESCRIPTION Ref. No. Application / Function Operation / Condition / Compatibility IC11 AMP for 4V Pre-Out Ref. IC12 Switching regulator IC for CD mecha D5V and FL filament IC902 AMP for Power IC SVR and E-vol IC 3.3V Ref.
Page 6
KDC-MP5028/MP528 /W6031/W6031Y MICROCOMPUTER’S TERMINAL DESCRIPTION MECHANISM MICROCOMPUTER 703030BYGCJ09A (X32-574 : IC4) Processing Operation Pin No. Pin Name Application Remarks Description Not used. Low-fixed E2P_SCL Rom correction E2P I2C clock Not used. Low-fixed 5V electric potential GND electric potential Not used.
Page 7
KDC-MP5028/MP528 /W6031/W6031Y MICROCOMPUTER’S TERMINAL DESCRIPTION Processing Operation Pin No. Pin Name Application Remarks Description Multiplex RD signal 3.3V driven ASTB Multiplex ASTB signal 3.3V driven Not used. Low-fixed 3.3V driven Not used. Low-fixed 3.3V driven 47~54 AD0~AD7 Multiplex address/data 3.3V driven...
Page 8
KDC-MP5028/MP528 /W6031/W6031Y MICROCOMPUTER’S TERMINAL DESCRIPTION MAIN MICROCOMPUTER 30624MWPA35GP (X34 : IC1) Module Truth Pin No. Pin Name Application Processing Operation Description (functional) Value Table REMO EXTRA Remote controller signal input Pulse width is detected. LX_MUTE LX_M Mute request from slave unit...
KDC-MP5028/MP528 /W6031/W6031Y MICROCOMPUTER’S TERMINAL DESCRIPTION Module Truth Pin No. Pin Name Application Processing Operation Description (functional) Value Table ROM correction E2PROM I2C clock SCL/ROMCOR_SCL EXTRA output terminal POWER ON : Hi-Z, POWER OFF : L, PON_PANEL Power supply I/O Panel 5V control terminal...
Page 10
KDC-MP5028/MP528 /W6031/W6031Y MICROCOMPUTER’S TERMINAL DESCRIPTION Module Truth Pin No. Pin Name Application Processing Operation Description (functional) Value Table OEM_DISP_CE EXTRA I/O External display control request External display O Not used. (M-destination only) Output L-fixed EXTRA O Not used. Output L-fixed...
KDC-MP5028/MP528 /W6031/W6031Y MICROCOMPUTER’S TERMINAL DESCRIPTION PANEL General Purpose Port Functional Allocation Pin No. Active (H/L) Pin Name Application Processing Operation Description RED : H RED LED control terminal GREEN : L RED : L GREEN GREEN LED control terminal GREEN : H...
KDC-MP5028/MP528 /W6031/W6031Y TEST MODE How to enter the test mode • AUTO : FM1_98.1A In order to enter the test mode, reset the unit while simulta- • Forced WIDE : FM1_98.1W neously pressing down [1] and [3] keys. • Forced MIDDLE : FM1_98.1M •...
Page 13
KDC-MP5028/MP528 /W6031/W6031Y TEST MODE 2-ZONE Items ter this, any of the item can be selected) * Normally, Sub Woofer Level is not included. In this ver- • When using sources other than the STANDBY source, us- sion, however, the Sub Woofer Level is included, and this ing a short-press on [AUTO] / [TI] key, 2-ZONE ON / OFF is has been already arranged.
KDC-MP5028/MP528 /W6031/W6031Y TEST MODE Other [5] Key Short-press : CD EJECT number of times is displayed. • At Power ON, “CODE_OFF”, “CODE_ON” displays will not During CD EJECT number of times display, be made. by long-pressing for 2 seconds, CD EJECT •...
Page 15
KDC-MP5028/MP528 /W6031/W6031Y TEST MODE Security gardless of whether a disc is in the unit or not. • Forced Power ON mode (All models) Panel full OPEN/CLOSE is conducted with a short-push. (Protection time : 3 seconds) Even in the case where security is in effect, by simultaneously...
Page 19
KDC-MP5028/MP528 /W6031/W6031Y D408 C429 R425 R948 C427 C426 D405 R946 Q300 R944 Q301 W123 X34-342x-xx/3762-71 Ref. No. Address C438 R401 R434 D412 Q101 Q103 Q114 R335 Q300 Q301 D305 R314 C326 Refer to the schematic diagram for the values of resistors and capacitors.
Page 20
KDC-MP5028/MP528 /W6031/W6031Y PC BOARD (COMPONENT SIDE VIEW) CD PLAYER UNIT X32-5740-0x (J76-0065-12) CP27 IC11 R150 X32-5740-0x Ref. No. Address IC11 Refer to the schematic diagram for the values of resistors and capacitors.
Page 21
KDC-MP5028/MP528 /W6031/W6031Y PC BOARD (FOIL SIDE VIEW) CD PLAYER UNIT X32-5740-0x (J76-0065-12) 12EJE-SW IOP- IOP+ CP28 ATEST AGND A3.3V REFOUTSV SHOCK LOS-SW LOCK HOLD DOUT DGND AGND C100 R104 WAIT CP10 CP9 S7.5V CP11 BU5V SGND TYPE LOE/LIM PON2 PON1...
KDC-MP5028/MP528 /W6031/W6031Y PC BOARD (COMPONENT SIDE VIEW) (FOIL SIDE VIEW) SWITCH UNIT SWITCH UNIT X16-2920-11/3142-70 X16-2920-11/3142-70 (J76-0050-12) (J76-0050-12) X16-2920-11/3142-70 X16-2920-11/3142-70 Ref. No. Address Ref. No. Address PAN5 REMO ROT-A ROT-B Refer to the schematic diagram for the values of resistors and capacitors.
Page 40
Installation Size (W x H x D) ....182 x 53 x 155mm ..........7-3/16 x 2-1/16 x 6-1/10inch Weight ............3.09lbs (1.4kg) KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.