Exterior Cleaning - KitchenAid LKUIX335PPS Series Owner's Manual

8. Remove the mounting screw that holds the water pan in place.
Pull out on the front of the water pan.
A.
Water pan
B.
Water pan screw
9. Disconnect the pump bracket from the water pan and unplug
the water pan drain pump.
10. Remove, clean, and replace the ice scoop holder and ice
scoop.
Lower left
A.
Screw
B.
Ice scoop holder
On Some Models
� After removing the ice scoop, remove the holder by
removing the two screws.
NOTE: On some upper left models, remove the holder by
lifting up on the ice scoop holder and then out.
� Wash the ice scoop holder and ice scoop along with the
other interior components using the following instructions.
� Replace the ice scoop holder by replacing the screws or,
on some upper left models, pushing in on the holder and
then down.
11. Wash the interior components (cutter grid, exterior of hoses,
and water pan) and the storage bin, door gasket, ice scoop,
and ice scoop holder with mild soap or detergent and warm
water. Rinse in clean water. Then clean the same parts with a
solution of 1 tbs (15 mL) of household bleach in 1 gallon
(3.8 L) warm water. Rinse again thoroughly in clean water.
NOTE: Do not remove hoses. Do not wash plastic parts in
dishwasher. They cannot withstand temperatures above
145°F (63°C).
12. To replace the water pan, set the water pan inside the ice bin.
Hook up the water pan pump. Snap the pump bracket back
onto the water pan and place back into position. Secure the
water pan by replacing the mounting screw.
20
C. Drain cap
D. Drain pump cover
13. Check the following:
� Drain cap from the water pan is securely in place. If the
drain cap is loose, water will empty from the water pan,
and you will have either thin ice or no ice.
� Hose from water pan is inserted into storage bin drain
opening.
14. Slide the cutter grid back into place and secure it by replacing
the right-hand screw and plastic spacer. Then tighten the
left-hand screw. Reconnect the cutter grid harness and the ice
level sensor harness.
15. Replace the cutter grid cover.
NOTE: On some models, replace the cutter grid cover using
the screw removed earlier.
16. Gently wipe the control panel with a soft, clean dishcloth using
warm water and a mild liquid dish detergent.
17. Plug in ice maker or reconnect power.
18. After cleaning, make sure that all controls are set properly and
that no control indicators are flashing.
Quick Clean
You will need to use one 16 oz (473 mL) bottle of approved ice
maker cleaner. We recommend using the *affresh Ice Machine
Cleaner.

Exterior Cleaning

The ice making system and the air-cooled condenser need to be
cleaned regularly for the ice maker to operate at peak efficiency
and to avoid premature failure of system components. See the
"Ice Maker System" and the "Condenser" sections.
Exterior Surfaces
Wash the exterior surfaces and gaskets with warm water and mild
soap or detergent. Wipe and dry. We recommend using a clean
microfiber cloth or a soft clean cloth to polish and dry.
For ice makers with a painted or colored exterior, regular use of a
good household appliance cleaner and polish will help protect the
finish. Using paper towels may scratch and/or dull the clear coat of
the painted door.
For ice makers with a fingerprint-resistant stainless steel exterior,
do not use soap-filled scouring pads, abrasive or harsh cleaners,
any cleaning product containing chlorine bleach, steel-wool pads,
gritty wash cloths, or paper towels. Using these types of products
may scratch and/or dull the clear coat of the fingerprint-resistant
stainless steel door.
Ice Maker System
Minerals that are removed from water during the freezing cycle
will eventually form a hard scaly deposit in the water system.
Cleaning the system regularly helps remove the mineral scale
buildup. How often you need to clean the system depends upon
how hard your water is. With hard water of 15 to 20 grains/gallon
(4 to 5 grains/liter), you may need to clean the system as often as
every 9 months.
NOTE: Use one 16 oz (473 mL) bottle of approved ice maker
cleaner. We recommend using the *affresh Ice Machine Cleaner.
To order, see "Accessories" on the ice maker Quick Start Guide.
1. Press the On/Off button.
2. Wait 5 to 10 minutes for the ice to fall into the storage bin.
Remove all ice from the storage bin.