1. Manuals
  2. Brands
  3. Vigilant Manuals
  4. Security System
  5. QE20
  6. Installation manual

Vigilant QE20 Installation Manual

Emergency warning system
Hide thumbs Also See for QE20:
Table of Contents

Advertisement

Quick Links

Download this manual
LT0712
QE20
EMERGENCY WARNING SYSTEM
INSTALLATION MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the QE20 and is the answer not in the manual?

Questions and answers

Related Manuals for Vigilant QE20

Summary of Contents for Vigilant QE20

  • Page 1 LT0712 QE20 EMERGENCY WARNING SYSTEM INSTALLATION MANUAL...
  • Page 3 QE20 Emergency Warning System Installation Manual DOCUMENT: LT0712 Issue 1.0 13 June 2023 QE20 is a product of Johnson Controls 17 Mary Muller Drive Christchurch NEW ZEALAND Phone : +64-3-389-5096 Copyright © 2023 Johnson Controls. All Rights Reserved. All specifications and other information shown were current as of document revision date and are...
  • Page 4 Document: LT0712 END USER LIABILITY DISCLAIMER Some of the operation of QE20 Emergency Warning System as described in this manual is dependent on site-specific configuration performed by the field engineer. If the configuration is not well-designed, then operation may differ from this manual and compliance to local installation standards may be invalidated.

  • Page 5: Table Of Contents

    Example Site Configuration ..................... 3-1 Circuit Usage Report ......................3-2 On-Site Programming ..................4-1 What’s Available ....................... 4-1 Placing Into Operation ................... 5-1 Initial Power Up ......................... 5-1 Check Field Wiring Before Connecting to QE20 ............5-1 Issue 1.0 13 June 2023 Page iii...
  • Page 6 Document: LT0712 Commissioning ......................... 5-2 Fault Finding ........................5-4 Spare Parts, Drawings ................... 6-1 Spare Parts ........................6-1 Drawings ..........................6-2 Module Installation ..................7-1 Installation Guide For Each QE20 Module ..............7-1 Page iv 13 June 2023 Issue 1.0...

  • Page 7: Introduction

    – in terms of the number of zones, amplifiers and power rating, power supplies, field wiring modules, and optional networking. A block diagram is shown in Figure 1. QE20 is highly configurable and expandable up to 224 emergency zones on the user interface.
  • Page 8 Fibre Network kit. Each QE20 will be supplied in one or more 19” rack mounting cabinets, with a Perspex window in the outer doors and the user interface mounted on hinged inner doors.
  • Page 9 Figure 2 shows an example front panel view, and Figure 3 an internal view. Figure 2 Example QE20 Front View Issue 1.0 13 June 2023...
  • Page 10 QE20 Installation Manual Document: LT0712 Figure 3 Example QE20 Internal View Page 1-4 13 June 2023 Issue 1.0...

  • Page 11: Specifications - Qe20 Panel

    Document: LT0712 QE20 Installation Manual Specifications – QE20 Panel Panel Size: Double 28U Double 40U Height (mm) 1330 1863 1330 1863 Width (mm) 1150 1150 MECP Depth (mm) SECP Depth (mm) Maximum number of zones with: 25W RMS Amps 60W RMS Amps...

  • Page 12: Other Qe20 & Product Manuals

    Use WIP/Input Module inputs High Level Links RZDU, Panel-Link, Computer Port (4100ESi) Max Inputs 320 WIP/Input; 528 RZDU, Unlimited – Panel-Link; 600 points 4100ESi Other QE20 & Product Manuals 1.4.1 VIGILANT QE20 Manuals LT0711 QE20 Operator Manual LT0709 QE20 Service Manual...

  • Page 13: Other Vigilant Manuals

    FP2005 RS485 Networking Module Install Guide LT0701 FP2006/7/8/9 Amplifier Modules Install Guide LT0702 FP1187/89 QE20 Hinge Kit Install Guide LT0703 FP1186 QE20 Module Mounting Frame Install Guide LT0705 FP2023 2 x 4-way 100V Splitter Module Install Guide LT0706 FP2010 Master User Interface Install Guide LT0707...
  • Page 14 QE20 Installation Manual Document: LT0712 THIS PAGE INTENTIONALLY LEFT BLANK Page 1-8 13 June 2023 Issue 1.0...

  • Page 15: Cabinet Installation & Wiring

    40U SECP (Shallow – 165mm) 1863 x 575 x 213 mm The QE20 could also be supplied as a “Combo” panel, where both a fire alarm system and the QE20 are installed in a single 40U deep cabinet. Handling & Checking Cabinets Precautions should be taken when handling the QE20 cabinets, as they can be of significant weight.

  • Page 16: Cabinet Installation

    • Have an ambient noise level of not more than 70 dB(A), • Not exceed the ambient operating conditions for the QE20, • Allow all the controls and indications of the QE20 to be within 750 mm and 1850 mm of the floor, •...
  • Page 17 Document: LT0712 QE20 Installation Manual Figure 4 QE20 Cabinet Wall Fixing Details Issue 1.0 13 June 2023 Page 2-3...

  • Page 18: Removal And Refitting Of Internal Mounting Frames

    Consideration should be given to future expansion of the QE20 at the time of selecting and installing the mains supply. The following table shows the recommended circuit breaker rating and...

  • Page 19: Turning Pse On And Off

    1.5mm 2.5mm 2.5mm The mains wiring to the QE20 cabinet is terminated in the single dual-outlet GPO (1- 2 PSE) or two dual-outlet GPOs (3-4 PSE). The GPO terminal capacity is a maximum of 3 x 2.5mm conductors, so fitting the incoming mains wire and a wire across to the other GPO is possible.

  • Page 20: Battery Installation & Wiring

    LM0652 to the positive terminal. Do not connect the Anderson connector until the QE20 has been initially powered up and tested. Wiring to a remote battery is not permitted.

  • Page 21: Internal 24V Dc Distribution

    Adjacent Cabinet Wiring Where a QE20 system consists of multiple adjacent cabinets it will be necessary to reconnect the factory fitted wiring between the cabinets. Long connecting cables will be included in any additional cabinets, to allow connection to the previous cabinet.

  • Page 22: Field Wiring

    QE20s when copper cabling is used. If fibre cabling is used, then additional equipment will be fitted to the QE20 to transport the audio signals over the fibre network.

  • Page 23: Zone, Wip And User Button Labels

    • Command Scripts table – Description for GUI / User Buttons field. Alternatively, there is a preformatted label, LB0694, that is available from the Fireplace website (vigilant-fire.com.au) as an editable PDF file and an AutoCAD drawing. Enter the required button descriptions into these forms and print them off.
  • Page 24 QE20 Installation Manual Document: LT0712 THIS PAGE INTENTIONALLY LEFT BLANK Page 2-10 13 June 2023 Issue 1.0...

  • Page 25: Site Configuration

    • Networking with other panels • Phased evacuation, messages, etc. A printout of the site configuration is supplied with each QE20 and is the key document defining what function has been assigned to each input and output of the QE20 and thus what field wiring should be connected and where.

  • Page 26: Circuit Usage Report

    The Circuit Usage Report available in QE20Config can be used to list the inputs and outputs assigned and their function. This can assist in terminating the field wiring to the correct terminals, if the wiring is labelled by zone number / location. QE20 Install Manual Example ********Amplifiers*********** Zone...

  • Page 27: On-Site Programming

    What’s Available Most site settings are entered into QE20Config to form the site configuration. This is downloaded to the QE20 and stored in non-volatile memory in the Controller, so it is available each time the QE20 is turned on. The following items can be configured on-site separately to the site configuration, so may be changed without requiring a computer with QE20Config installed and access to change the configuration.
  • Page 28 QE20 Installation Manual Document: LT0712 Rotate the knob to obtain the desired volume and touch SET VOL. The amplifier volume will be changed. Check the volume in the area is appropriate. Next time the site configuration is extracted or before it is changed, a prompt will be given to merge the on-site volume settings with the site configuration.
  • Page 29 CANCEL to abort. Note the background music setting is lost on power down / restart of the QE20 and will be initialised on power up to a state defined by the installer. Issue 1.0...
  • Page 30 QE20 Installation Manual Document: LT0712 THIS PAGE INTENTIONALLY LEFT BLANK Page 4-4 13 June 2023 Issue 1.0...

  • Page 31: Placing Into Operation

    • Install the QE20 cabinets and complete the mains power wiring to the cabinets. If permanent mains wiring is not available, temporary wiring may be used as long as the QE20 has no VADs or 100V loads connected (so the power consumption is minimal).

  • Page 32: Commissioning

    QE20Config or manually filled in from the configuration) and fit to the pockets in the user interface. The general steps for commissioning a QE20 are as follows (also refer to each QE20 module installation guide for specific commissioning instructions). • For each evacuation zone:...
  • Page 33 Activate an appropriate zone alarm (or test the zone) on the fire panel and check the correct zone on the QE20 goes into alarm. Reset the alarm at the fire panel, then Reset the alarm on the QE20 and check all zones are normal.

  • Page 34: Fault Finding

    QE20 Installation Manual Document: LT0712 Check that the fault on the QE20 generates a fault on the fire panel if the fire panel monitors the QE20 for faults. • With no batteries connected put all zones (or at least those in each cabinet) into evacuate at the same time.

  • Page 35: Spare Parts, Drawings

    Document: LT0712 QE20 Installation Manual Spare Parts, Drawings Spare Parts Note most QE20 products are labelled with the part number of their replacement part. Part Number QE20 Module Spare / Additional Item FP2000 QE20 Controller Module FP2001 QE20 27A Power Supply Equipment (PSE)

  • Page 36: Drawings

    Desk Mount Microphone PA0688 Microphone Preamp Board 1923-19 PA0646 ALIM9706 Audio Line Isolator FP0938 QE20 WIP Phone Red, Master or Field WIP. SU0608 White MCP (EVACUATE Lettering) SU0615 Transparent Hinged Cover to suit Manual Call Points A2260 10W audio attenuator...

  • Page 37: Module Installation

    FP2005 RS485 Networking Module Install Guide LT0701 FP2006/7/8/9 Amplifier Modules Install Guide LT0702 FP1187/89 QE20 Hinge Kit Install Guide LT0703 FP1186 QE20 Module Mounting Frame Install Guide LT0705 FP2023 2 x 4-way 100V Splitter Module Install Guide LT0706 FP2010 Master User Interface Install Guide LT0707...
  • Page 38 QE20 Installation Manual Document: LT0712 Page 7-2 13 June 2023 Issue 1.0...
  • Page 39 Document: LT0712 QE20 Installation Manual Replace with 2001-1 Sheet 8 Multi-cabinet Wiring – User Interfaces UBus Issue 1.0 13 June 2023 Page 7-3...
  • Page 40 QE20 Installation Manual Document: LT0712 Replace with 2001-1 Sheet 9 Multi-cabinet Wiring – Amplifiers Page 7-4 13 June 2023 Issue 1.0...
  • Page 41 Document: LT0712 QE20 Installation Manual Replace with 2001-1 Sheet 10 Multi-cabinet Wiring – Power Issue 1.0 13 June 2023 Page 7-5...
  • Page 42 QE20 Installation Manual Document: LT0712 Replace with 2001-1 Sheet 11 Multi-cabinet Wiring – QBus – WIP, ROM, PSE Page 7-6 13 June 2023 Issue 1.0...
  • Page 43 Document: LT0712 QE20 Installation Manual Replace with 2001-1 Sheet 12 Multi-cabinet Wiring – WIP Audio Issue 1.0 13 June 2023 Page 7-7...

Table of Contents