Subscribe to Our Youtube Channel
Related Manuals for Cuppone Leonardo
Summary of Contents for Cuppone Leonardo
- Page 1 Original instructions Leonardo Leonardo 4.0 OVEN Pre-installation and installation manual LN2T/1TS | 1TSH LN3T/1TS | 1TSH LN650/1TS...
-
Page 2: Table Of Contents
Before the installation, read the content of this manual ly: it contains important information regarding product assem- Leonardo 2T oven technical data ................7 Leonardo 3T oven technical data ................12 bly and safety regulations. Leonardo 650 oven technical data ................17 INSTALLATION .......... -
Page 3: Checks Before Purchasing
(not supplied) eyebolts supplied by the Manufacturer (they are inside the incorrect lifting with a single oven chamber) coupling point Fig.1. Ed. 0423 - 70702551 REV06 Leonardo - Installation... -
Page 4: Checks Before Purchasing
Checks before purchasing Survey the installation room to make sure it is ade- Fig.2. • It is possible to maintain the following minimum dis- quate. walls, appli- tances between the oven and the other ances, objects combustible materials Fig.4.: √ Fig.3. -
Page 5: Checks Before Purchasing
• must be connected to an [1.97 in.] [1.97 in.] housing with suitable systems. breaker allowing complete disconnection in over- voltage III category conditions. Fig.4. Ed. 0423 - 70702551 REV06 Leonardo - Installation... -
Page 6: Oven Technical Data
OVEN TECHNICAL DATA Electrical data Power supply Power Average consumption Absorption Cable type Customer panel prot. Oven model (kW) (kWh) (Nxmm (NxA) LN2T/1TS-C5-CP 3Nx400V 17.0 5x2.5 4x20 LN2T/1TS-B5-CP h.18 3x230V 11.8 29.6 3x40 LN2T/1TS-B6-US 3x208V 32.8 4xAWG7 3x40 LN2T/1TSH-C5-CP 3Nx400V 17.0 5x2.5 4x20... -
Page 7: Leonardo 2T Oven Technical Data
Leonardo 2T oven technical data 245mm 9,63in 651,5mm 25,65in 411,5mm 16,21in 457,5mm 18,01in 850,5mm 33,48in Ø85mm 3,37in 70mm 2,76in 570,50mm 22,46in 127mm 5,00in 887mm 34,92in 294mm 11,57in 737,50mm 29,04in 10mm 0,39in 1308mm 51,50in 1318mm 51,89in 820mm 32,28in refractory rusticated refractory... - Page 8 Leonardo 2T oven technical data 1318mm 51,89in 10mm 0,39in 1308mm 51,50in 30mm 1,18in 47mm 1,85in 1148mm 45,20in 58,50mm 2,30in h.18 h.25 400mm [15,77 in.] 470mm [18,52 in.] 174mm [6,86 in.] 244mm [9,61 in.] 279mm [10,98 in.] 349mm [13,74 in.] without steamer 280mm [11,02 in.]...
- Page 9 570,50mm 294mm 11,57in 22,46in 127mm 5,00in Leonardo 2T oven technical data 887mm 34,92in 737,50mm 29,04in 10mm 0,39in 1308mm 51,50in COOKING CHAMBER DIMENSIONS 1318mm 51,89in 820mm 32,28in PIZZA Ø 50 cm [Ø 19.69 in.] PIZZA Ø 35 cm [Ø 13.78 in.] TRAY 60x40 cm [23.62x15.75 in.]...
- Page 10 Leonardo 2T support technical data 962mm 37,87in 713mm 28,07in 1308mm 51,50in 1162mm 45,75in inch 17,72 20,87 27,17 30,32 33,47 36,62 1010 39,77 1090 1170 173mm 6,81in...
- Page 11 Leonardo 2T hood technical data 1084mm 42,68in 731mm 28,78in 583mm 22,95in 1314mm 51,73in 833mm 32,80in 460,50mm 1308mm 51,50in 18,13in 853,50mm 33,60in 475mm 18,70in Ø80mm 3,15in Ø147mm 5,79in A Supply input B Oven smoke exhaust C Hood fume inlet D Extraction fan...
-
Page 12: Leonardo 3T Oven Technical Data
Leonardo 3T oven technical data 449,5mm 17,70in 651mm 25,62in 617,5mm 24,28in 1108,5mm 609,5mm 43,64in 24,00in 70mm 2,76in 1297mm 51,06in 775,50mm 30,53in 942,50mm 37,11in 127mm 5,00in 294mm 11,57in 10mm 0,39in 1718mm 67,64in 1728mm 68,03in 1230mm 48,58in refractory rusticated refractory rusticated model... - Page 13 Leonardo 3T oven technical data 1728mm 68,03in 10mm 0,39in 1718mm 67,64in 30mm 1,18in 47mm 58,50mm 1,83in 1148mm 45,20in 2,30in h.18 h.25 400mm [15,77 in.] 470mm [18,52 in.] 174mm [6,86 in.] 244mm [9,61 in.] without steamer 279mm [10,98 in.] 349mm [13,74 in.] 280mm [11,02 in.]...
- Page 14 2,76in 1297mm 51,06in Leonardo 3T oven technical data 775,50mm 30,53in 942,50mm 37,11in 127mm 5,00in 294mm 11,57in 10mm 0,39in 1718mm 67,64in COOKING CHAMBER DIMENSIONS 1728mm 68,03in 1230mm 48,58in PIZZA Ø 35 cm PIZZA Ø 50 cm TRAY 60x40 cm [Ø 13.78 in.] [Ø...
- Page 15 Leonardo 3T support technical data 1372mm 54,02in 713mm 28,07in 1718mm 67,64in 1572mm 61,89in inch 17,72 20,87 27,17 30,32 33,47 36,62 1010 39,77 1090 173mm 6,81in 1170 Ed. 0423 - 70702551 REV06 Leonardo - Installation...
- Page 16 Leonardo 3T hood technical data 1084mm 42,68in 1724mm 67,87in 937mm 36,89in 786mm 30,94in 833mm 32,80in 475mm 18,70in 1718mm 67,64in 612,50mm 24,11in 1111,50mm 43,76in Ø80mm 3,15in 147mm 5,79in A Supply input B Oven smoke exhaust C Hood fume inlet D Extraction fan...
-
Page 17: Leonardo 650 Oven Technical Data
Leonardo 650 oven technical data 633mm 24,91in 651mm 25,65in 799,5mm 31,48in 561mm 22,09in 795mm 31,30in 728mm 28,66in 1663mm 65,47in 127mm 5,00in 294mm 11,57in 70mm 10mm 2,76in 0,39in 2084mm 82,05in without with 2094mm 82,44in 958,50mm 37,74in 1125,50mm 44,31in steamer steamer 1600mm 63,78in... - Page 18 Leonardo 650 oven technical data 2094mm 82,44in 10mm 0,39in 2084mm 82,05in 30mm 1,18in 58,50mm 2,30in 47mm 174mm 1,85in 1469mm 57,83in 6,86in 1690mm 66,54in without steamer with steamer 799,5mm 31,48in 651,5mm 25,65in 633mm 24,91in A Supply input Equipotential 174mm C Steamer connection...
- Page 19 1663mm 65,47in 127mm 5,00in 294mm 11,57in 70mm Leonardo 650 oven technical data 10mm 2,76in 0,39in 2084mm 82,05in 2094mm 82,44in 958,50mm 37,74in 1125,50mm 44,31in PIZZA Ø 50 cm [Ø 19.69 in.] 1600mm 63,78in PIZZA Ø 35 cm [Ø 13.78 in.] TRAY 60x40 cm [23.62x15.75 in.]...
- Page 20 Leonardo 650 support technical data 1738mm 68,43in 1034mm 40,71in 2084mm 82,05in 1936,50mm 76,24in inch 17,72 20,87 27,17 30,32 33,47 36,62 1010 39,77 1090 1170 173mm 6,81in...
- Page 21 Leonardo 650 hood technical data 1084mm 42,68in 833mm 32,80in 2090mm 82,28in 1045mm 41,14in 1045mm 41,14in 2084mm 82,05in 564mm 475mm 18,70in 731mm 28,78in 795mm 31,30in 22,20in 147mm 5,79in 80mm 3,15in 80mm 3,15in A Supply input B Oven smoke exhaust C Hood fume inlet...
-
Page 22: Installation
INSTALLATION Symbols used in the manual and on Safety instructions • Installation or maintenance that fails to comply with the instructions in this manual may cause the labels applied to the machine damage, injury or fatal accidents. • Read this guide carefully before installing the Indicates that caution is required when performing •... -
Page 23: Preliminary Operations
Fig.5. Caution, suffocation hazard! If left unattended, packaging could be potentially dangerous for both children and animals. Caution, hindrance hazard! If left unattended, packaging could hinder vehicles and installers during assembly operations. Ed. 0423 - 70702551 REV06 Leonardo - Installation... -
Page 24: Transport And Positioning Of The Oven On The Planned Base
Installation Transport and positioning of the oven on the planned base Fig.6. Fitted with personal protection equipment, transport the appliance to the installation location. Use suitable equipment, capable of dealing with its weight: persons not involved with the appli- ance installation may not pass through or stand in the work area during the appliance assembly. During the transport, pay particular attention to passing through openings and/or doors. To lift eyebolts frame the appliance, it is vital to fit the 4... - Page 25 25 387 kg - 853 lb 347 kg - 765 lb If the Leonardo oven must For a correct installation it is necessary to seal the gap created between the base of the oven and the rest on a support, make the...
- Page 26 Installation Fig.8. Please make sure the installation room is adequate and comply walls, with the minimum distances of the oven from other pliances, objects combustible materials (see page 4). Remove the eyebolts and refit the previously re- Once the oven is positioned on the intended base, if: moved screws.
-
Page 27: Placing Several Ovens One On Top Of The Other
The other ovens must be lifted with the same precautions and methods adopted for the first one. Lifting from the ground must be perpendicular to the ground itself and the tension of the eyebolts must be vertical Ed. 0423 - 70702551 REV06 Leonardo - Installation... - Page 28 Installation BACK/x3 LN2T/3T/650: LN2T/3T/650: LN4T/6T: LN4T/6T:...
-
Page 29: Placing Several Ovens One On Top Of The Other With A Hood Installed
The other ovens must be lifted with the same precautions and methods adopted for the first one. Fig.10. Ed. 0423 - 70702551 REV06 Leonardo - Installation... - Page 30 Installation BACK/x3 LN2T/3T/650: LN2T/3T/650: LN4T/6T: LN4T/6T:...
- Page 31 Installation Ed. 0423 - 70702551 REV06 Leonardo - Installation...
-
Page 32: Serial Number Plate Reading
Installation Serial number plate reading The serial number is on the right hand side of the appliance. Model Year of production It provides important technical information that is vital in case Voltage of a request for maintenance or repair of the appliance: please do not remove, damage or modify it. -
Page 33: Electrical Connection
T - S - L... - R -: earth earth neutral neutral T - S - L... - R -: T - S - L... - R -: Fig.13. phases phases AC 3 208 AC 3 208 Ed. 0423 - 70702551 REV06 Leonardo - Installation... - Page 34 Installation Fig.14. For a correct electrical connection, the appliance must: equipotential system • be included in an in compliance with the legislation in force. This connection must be made between the various devices with the terminal marked with the equipotential symbol .
- Page 35 Light transformer 50VA, 230/12Vac Taglio Platea double outlet Cielo Comune Steamer Alimentazione Abbreviation STEAMER description Uscita Taglio fase Water inlet solenoid valve Heating element TC TC VAPORIERA Manually reset safety thermostat Heating element switching relay Ed. 0423 - 70702551 REV06 Leonardo - Installation...
- Page 36 Installation AC3 N 400 Abbreviation PIN description Phase downstream from KM1 Technical room fan From safety thermostat to KM1 coil Phase upstream from KM1 Smoke vent opening motor Cooking chamber lights Steam evacuation 0,12 microF Steamer heating element supply SSR_A1 SSR_Rt SSR_B1 Phase downstream from KM1...
- Page 37 Lower heating element solid state relay Terminal board Thermocouple Θ Light transformer 50VA, 230/12Vac double outlet Steamer Abbreviation STEAMER description Water inlet solenoid valve Heating element Manually reset safety thermostat Heating element switching relay Ed. 0423 - 70702551 REV06 Leonardo - Installation...
- Page 38 Installation AC3 208 Abbreviation PIN description Phase downstream from KM1 Technical room fan From safety thermostat to KM1 coil Phase upstream from KM1 Smoke vent opening motor Cooking chamber lights Steam evacuation Steamer heating element supply Phase downstream from KM1 Abbreviation Description Control panel supply 25.2W, 230Vac/12Vcc...
- Page 39 Light transformer 50VA, 230/12Vac screen double outlet Taglio Platea Cielo Steamer Comune Abbreviation STEAMER description Alimentazione Uscita Taglio fase Water inlet solenoid valve Heating element TC VAPORIERA Manually reset safety thermostat Heating element switching relay Ed. 0423 - 70702551 REV06 Leonardo - Installation...
- Page 40 Installation AC3 230 Abbreviation PIN description Phase downstream from KM1 Technical room fan From safety thermostat to KM1 coil Phase upstream from KM1 Smoke vent opening motor Cooking chamber lights Steam evacuation 0,12 microF Steamer heating element supply SSR_A1 SSR_Rt SSR_B1 Phase downstream from KM1 SSR_A2...
-
Page 41: Pre-Testing And Final Inspection
Does the user have all the documentation relative to the oven? optimal and safe way and how to carry out ordinary mainte- Has the user been correctly trained on the use and maintenance of the oven? nance and cleaning. Ed. 0423 - 70702551 REV06 Leonardo - Installation... -
Page 42: Steamer Assembly (Option)
Steamer assembly (option) It is possible to connect to Leonardo ovens the steamer accessory mod. N602870184 WARNING! DISCONNECT THE OVEN FROM THE MAINS BEFORE INSTALLING THE STEAMER... - Page 43 Steamer assembly (option) 1/4” Ed. 0423 - 70702551 REV06 Leonardo - Installation...
-
Page 44: Procedures
PROCEDURES Multimedia page Fig.16. From this page it is possible to import/export files from/to a USB stick connected to the special USB connector. Fig.16. The USB port is located inside the oven, behind the touch display and is accessible only by re- moving the right side of the appliance. -
Page 45: Procedures | Firmware Update
With the oven in stand-by, touch the icon. FIRMWARE VERSIONS Touch the icon The display will show the firmware version installed on the BACK ARROW oven; press the to exit the screen. Ed. 0423 - 70702551 REV06 Leonardo - Installation... - Page 46 Procedures | FIRMWARE UPDATE CUPLOADING THE UPDATED FIRMWARE Unscrew the screws that retain the side panel Remove the side panel and access the board behind the Touch panel Insert the stick on which the 6 update files were copied into the USB port located behind the Touch board.
- Page 47 Start the uploading process. As the firmware is loaded, the bar will turn orange to indicate the progress of the loading procedure. Aggiornamento pronto Parametri Test I/0 Firmware START update Aggiornamento pronto ESCI Ed. 0423 - 70702551 REV06 Leonardo - Installation...
-
Page 48: Procedures | Counter Hour Reset
Procedures | COUNTER HOUR RESET A counter inside the oven counts the work hours carried out; after a Giovedì 07.07.2022 20.14 certain number of hours, a pop-up appears on the display that warns BASKET Touch the icon next to “Hours since last maintenance: 5* (h)” about the need to carry out maintenance on the oven. - Page 49 SERVICE Touch the icon to go back to the stand-by screen. Ed. 0423 - 70702551 REV06 Leonardo - Installation...
-
Page 50: Maintenance And Cleaning
MAINTENANCE AND CLEANING Warnings Oven cleaning switch off the Before any cleaning, it is necessary to CLEANING THE EXTERNAL STEEL PARTS power to the appliance (acting on the system switch) and Use a cloth dampened with hot soapy water and end with rins- wear suitable personal protection equipment (e.g. - Page 51 Therefore, if you want to start it at midnight on Tuesday, you must When the pyrolysis function starts, the room select the key relating to that day. lights are turned off to preserve them. CHAMBER CLEANING WITH PYROLYSIS IN "WEEKLY Fig.19. Ed. 0423 - 70702551 REV06 Leonardo - Installation...
-
Page 52: Replacing Components
Maintenance and cleaning | REPLACING COMPONENTS Replacing components The user must replace only the stated compo- nents: in case of a fault or for extraordinary mainte- nance, contact the Dealer, requesting service from an authorised technician. As replacements, always use original spare parts to be requested from the Manufacturer: using non... - Page 53 Maintenance and cleaning | REPLACING COMPONENTS REPLACING THE REFRACTORY BRICKS Fig.23. Fig.23. Ed. 0423 - 70702551 REV06 Leonardo - Installation...
- Page 54 CUPPONE since 1963 CUPPONE S.R.L. Via Sile, 36 31057 Silea (TV) - ITALY T +39 0422 361143 F +39 0422 360993 info@cuppone.com - www.cuppone.com...
Need help?
Do you have a question about the Leonardo and is the answer not in the manual?
Questions and answers