NEC LED-FC012i User Manual
Led module
Hide thumbs
Also See for LED-FC012i:
- Installation and maintenance manual (64 pages) ,
- Safety manual (16 pages)
Related Manuals for NEC LED-FC012i
Summary of Contents for NEC LED-FC012i
- Page 1 User’s Manual LED Module [Models for indoor use] LED-FC009i LED-FC012i LED-FC015i MODELS: LED-FC009i, LED-FC012i, LED-FC015i...
-
Page 2: Table Of Contents
Table of Contents Important Information ..............English-1 Contents ..................English-5 Related Items for Installation ............English-6 Parts Name and Functions ..............English-7 Wiring ....................English-9 Specifications ................English-10 Diagram ..................English-11... -
Page 3: Important Information
Important Information Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LED DISPLAY SYSTEM: About the Symbols To ensure safe and proper use of the product, this manual uses a number of symbols to prevent injury to you and others as well as damage to property. - Page 4 ● Be sure to read the following before using the product to use it correctly and safely. WARNING Do not apply vibrations or shocks to the Install the product so that the vents are not product. obstructed. Make sure there are enough people available Do not install the product to unstable to ensure safety (at least two people) when locations or locations subject to vibrations.
- Page 5 CAUTION Do not use or store the product in the When connecting the power cord to the following places. product’s AC IN terminal, make sure the • Near heaters connector is fully and firmly inserted. • Places with lots of humidity or dust, or Do not damage the power cord.
- Page 6 Recommended Use & Maintenance About the LED lamps The surface of the pixel card is vulnerable to shocks, so do not press or hit the surface. LED lamps are sensitive to static electricity and surge voltage, which may damage their components and decrease their reliability.
-
Page 7: Contents
Contents The supplied parts are as follows. In case one of these parts is missing or damaged, contact the retailer. CAUTION Depending on the system you ordered, there is a cabinet without the upper connector. [Cabinet] [Pixel card] 8 cards per cabinet English - 5... -
Page 8: Related Items For Installation
Related Items for Installation The items required when installing the system are shown below. Contact your retailer for more details. [Power cord] To connect the LED module to the power distributor [LAN cable] To connect two LED modules together (120 mm for vertical connection, 1000 mm for horizontal connection) [Cabinet alignment bracket] [Connection screw for LED modules] [USB drive]... -
Page 9: Parts Name And Functions
Parts Name and Functions ⑥ ② ④ ⑫ Front Rear ⑪ ⑦ ⑩ ⑧ ① ③ ⑤ ⑨ Name Description Interface connectors Input and output connectors for the signal and AC power. To input the signal from the LED controller or the previous LED module. 12 Signal input/output When a signal is input into 1, the signal is output from 2. - Page 10 There are two types of cabinets. (1) Type A The connectors are equipped on the top and bottom sides. There are guide pins on the top. Receiving Power unit card (2) Type B There are no connectors on the top side. There are no guide pins. Power unit Receiving card...
-
Page 11: Wiring
The maximum number of connections per LAN cable is shown below. Product name Maximum number of connections LED-FC009i 2 modules LED-FC012i 5 modules LED-FC015i 7 modules CAUTION The maximum number of connections may differ depending on the connected LED controller. Therefore, check the specifications of the LED controller you are using. -
Page 12: Specifications
Specifications LED-FC012i LED-FC015i LED-FC009i LED configuration Flip chip COB (chip size : 4mil*8mil) Pixel pitch 0.95 mm 1.26 mm 1.58 mm Number of displayed pixels (resolution/module) 640 × 340 480 × 270 384 × 216 Brightness 800 cd/m Contrast ratio... -
Page 13: Diagram
Diagram LED-FC009i / LED-FC012i / LED-FC015i 48.5 Rear 4 x M8 18.5 (Unit: mm) English - 11... - Page 14 According to EU directive 2006/66/EC and amendments, the battery can’t be disposed improperly. The battery shall be separated to collect by local service. Service & Support in Europe Please contact: Sharp NEC Display Solutions Europe GmbH. Landshuter Allee 12-14, D-80637 München Phone: + 49 (0) 89/99699-0...