Advertisement
2
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included hex key
and your own phillips screwdriver
shaft at least 6" long) and wire cutters
Use the drawings below to identify the hardware used during assembly. Note: If a part is not in the parts bag,
check to see if it has been preattached to one of the parts to be assembled.
Extension Leg Nut (67)–4
Star Washer (8)–8
Console Bolt (64)–4
1. Make sure that the power cord is unplugged.
With the help of a second person, carefully tip the
treadmill onto its left side as shown. Partially fold the
Frame (58) so the treadmill is more stable. Do not fully
fold the treadmill until it is completely assembled.
Insert an Extension Leg (89) into the base of the Uprights
(84) as shown. Next, hold two Extension Leg Nuts (67) in
the bottom of the Extension Leg. Then, insert two
Extension Leg Bolts (65) with Star Washers (8) into the
top of the Extension Leg, and firmly tighten the Extension
Leg Bolts into the Extension Leg Nuts.
With the help of a second person, carefully tip the tread-
mill onto its other side. Attach the other Extension Leg
(not shown) as described above.
Attach four Base Pads (82) (only two are shown) to the
base of the Uprights (84) with four 1" Tek Screws (83).
.
1" Tek Screw (83)–4
Latch Screw (50)–2
Extension Leg Bolt (65)–4
1
84
65
8
82
67
89
58
6
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call the telephone number on the front
cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 10.) If an ex-
(with a
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
82
PROBLEM: The display of the console does not function properly
83
SOLUTION: a. Remove the key from the console and UNPLUG THE
tension cord is needed, use only a 3-conductor, 1 mm
m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the circuit breaker located on the treadmill
frame near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d. Check the on/off switch located on the treadmill
frame near the power cord. Make sure that the switch
is in the on position.
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. Make sure that the on/off switch is in the on position.
e. If the treadmill still will not run, see the front cover of this manual.
POWER CORD. With the help of a second person,
carefully tip the Uprights (84) down as shown. Next,
remove the three Screws (3) and the three Hood
Screws (7). Note: A phillips screwdriver with a shaft at
least 5" long is required.
27
2
(14-gauge) cord that is no longer than 1.5
c
Tripped
Reset
d
On
Position
a
3
7
3
84
Advertisement
