Page 1
NV SERIES AMPLIFIER MODELS NV−AM16001, NV−AM25001, NV−AM10002, NV−AM20004...
Page 2
NV SERIES Embrace the ultimate in power. The NV Series is the pinnacle of modern car audio. State of the art engineering ensures the most refined sound available is delivered at unparalleled levels. The NV Series represents the finest work FUSION has achieved; designed and manufactured to the highest level with no compromises.
AMPLIFIER FEATURES FUSION has designed and engineered a full range of efficient amplifiers, displaying a full cast aluminium heatsink with unique NV Series super graphic and the latest in ‘regulated amplifier technology’. The NV Series Amplifier range provide strength, style and great sound reproduction so you can be heard before you can be seen.
WARNING: Do not mount any amplifier on a subwoofer enclosure, as extended exposure to vibration may cause malfunction of the amplifier. To avoid scratching your new FUSION Amplifier, pre-drill the mounting holes with either a 3mm or 9/64" diameter drill bit and use the screws supplied in the accessory kit..
Make sure before any connection is made to the amplifier or source unit, ensure that you turn the audio system off. Failure to do so could result in either the stock system or your new FUSION product being damaged. FUSION does not warranty damaged amplifiers due to incorrect installation.
Use a fuse or circuit breaker of equal value as that found on the chassis of your FUSION amplifier. You may now connect the cable to the battery, but remember to leave the fuse out or circuit breaker off until all other cable connections are made.
Page 14
SPEAKER TERMINAL BLOCK SPEAKER LOAD Keep in mind FUSION NV Series Amplifier series are high power amplifiers and not high current amplifiers. In other words, they require a minimum impedance of 2 ohms STEREO and 4 ohms bridged MONO to operate trouble free. Too low an impedance could send your FUSION amplifier into protection mode and/or damage the amplifier.
Page 15
Choose the correct length and style of RCA interconnects for your needs. The FUSION range of RCA’s gives you a variety of alternative solutions. These have multiple layers of shielding or are a twisted pair variety for better noise rejection (consult your FUSION dealer if unsure which to purchase).
CONTROL DESCRIPTIONS MONOBLOCK AMPLIFIER NV-AM16001 9 10 11 POWER AND STATUS LED’S: This displays ‘Green’ if the amplifier has been correctly powered up and ‘Red’ if any faults are present. BASS BOOST: This is a variable control to increase the bass boost at 45Hz from 0-+12dB of gain, adjust to suit. PHASE CONTROL: Adjust the phase control from 0 to 180 degree to adjust the in phase or out of phase subwoofer direction to the vehicles system.
Page 17
SUBSONIC: This is a variable control that filters out all sub bass frequencies below the set point at 12dB/Octave. LEVEL: This allows level adjustment of the input signal. Use this control to correctly match the head unit to the amplifier. To set this control correctly, turn the amplifier level to MIN and the head unit to 3/4 volume, with the bass and treble on zero, then slowly turn up this amplifier level control towards the MAX end of the control.
CONTROL DESCRIPTIONS MONOBLOCK AMPLIFIER NV-AM25001 9 10 11 POWER AND STATUS LED’S: This displays ‘Green’ if the amplifier has been correctly powered up and ‘Red’ if any faults are present. BASS BOOST: This is a variable control to increase the bass boost at 45Hz from 0-+12dB of gain, adjust to suit. PHASE CONTROL: Adjust the phase control from 0 to 180 degree to adjust the in phase or out of phase subwoofer direction to the vehicles system.
Page 19
SUBSONIC: This is a variable control that filters out all sub bass frequencies below the set point at 12dB/Octave. LEVEL: This allows level adjustment of the input signal. Use this control to correctly match the head unit to the amplifier. To set this control correctly, turn the amplifier level to MIN and the head unit to 3/4 volume, with the bass and treble on zero, then slowly turn up this amplifier level control towards the MAX end of the control.
CONTROL DESCRIPTIONS 2 CHANNEL AMPLIFIER NV-AM10002 10 11 12 POWER AND STATUS LED’S: This displays ‘Green’ if the amplifier has been correctly powered up and ‘Red’ if any faults are present. CROSSOVER SELECTOR: Set the appropriate mode of operation. The three positions available are OFF, LP and HP. See points 3 and 4 below.
Page 21
HIGH PASS: Set the crossover switch 2 to HP and turn this control to 65Hz or above when using speakers smaller than 6 x 9”. This feature is designed to filter out all low bass frequencies that only subwoofers should produce. Note: Failure to do so could result in speaker damage.
CONTROL DESCRIPTIONS 4 CHANNEL AMPLIFIER NV-AM20004 11 12 POWER AND STATUS LED’S: This displays ‘Green’ if the amplifier has been correctly powered up and ‘Red’ if any faults are present. CROSSOVER SELECTOR Set the appropriate mode of operation. The three positions available are OFF, LP and HP. See points 3 and 4.
Page 23
HIGH PASS: Set the crossover switch 2 to HP and turn this control to 65Hz or above when using speakers smaller than 6 x 9”. This feature is designed to filter out all low bass frequencies that only subwoofers should produce. Note: Failure to do so could result in speaker damage.