Settings Menu; Main Zone; Additional Zone - Daikin ETBH12EF6V Installation Manual

7 Configuration
To define the setpoint mode
To use the weather-dependent curve, you need to define the correct
setpoint mode:
Go to setpoint mode ...
Main zone – Heating
[2.4] Main zone > Setpoint
mode
Main zone – Cooling
[2.4] Main zone > Setpoint
mode
Additional zone – Heating
[3.4] Additional zone >
Setpoint mode
Additional zone – Cooling
[3.4] Additional zone >
Setpoint mode
Tank
[5.B] Tank > Setpoint mode
To change the type of weather-dependent curve
To change the type for all zones (main + additional) and for the tank,
go to [2.E] Main zone > WD curve type.
Viewing which type is selected is also possible via:
▪ [3.C] Additional zone > WD curve type
▪ [5.E] Tank > WD curve type
Restriction: Only available to installers.
To change the weather-dependent curve
Zone
Main zone – Heating
Main zone – Cooling
Additional zone – Heating
Additional zone – Cooling
Tank
INFORMATION
Maximum and minimum setpoints
You cannot configure the curve with temperatures that are
higher or lower than the set maximum and minimum
setpoints for that zone or for the tank. When the maximum
or minimum setpoint is reached, the curve flattens out.
To fine-tune the weather-dependent curve: slope-offset curve
The following table describes how to fine-tune the weather-
dependent curve of a zone or tank:
You feel ...
At regular outdoor At cold outdoor
temperatures ... temperatures ...
OK Cold
OK Hot
Cold OK
Cold Cold
Installation manual
28
Set the setpoint mode to ...
WD heating, fixed cooling
OR Weather dependent
Weather dependent
WD heating, fixed cooling
OR Weather dependent
Weather dependent
Restriction: Only available to
installers.
Weather dependent
Go to ...
[2.5] Main zone > Heating WD
curve
[2.6] Main zone > Cooling WD
curve
[3.5] Additional zone >
Heating WD curve
[3.6] Additional zone >
Cooling WD curve
Restriction: Only available to
installers.
[5.C] Tank > WD curve
Fine-tune with slope and
offset:
Slope Offset
↑ —
↓ —
↓ ↑
— ↑
You feel ...
At regular outdoor At cold outdoor
temperatures ... temperatures ...
Cold Hot
Hot OK
Hot Cold
Hot Hot
To fine-tune the weather-dependent curve: 2-points curve
The following table describes how to fine-tune the weather-
dependent curve of a zone or tank:
You feel ...
At regular outdoor At cold outdoor
temperatures ... temperatures ...
OK Cold
OK Hot
Cold OK
Cold Cold
Cold Hot
Hot OK
Hot Cold
Hot Hot
(a) curve" [ 4 26].
See "7.3.2 2-points
7.4

Settings menu

You can set additional settings using the main menu screen and its
submenus. The most important settings are presented here.
7.4.1

Main zone

Thermostat type
Only applicable in external room thermostat control.
NOTICE
If an external room thermostat is used, the external room
thermostat will control the room frost protection. However,
the room frost protection is only possible if [C.2] Space
heating/cooling=On.
# Code
[2.A] [C–05] External room thermostat type for the
main zone:
▪ 1: 1 contact: The used external room
thermostat can only send a thermo
ON/OFF
separation between heating or cooling
demand.
▪ 2: 2
room thermostat can send a separate
heating/cooling
condition.
7.4.2

Additional zone

Thermostat type
Only applicable in external room thermostat control. For more info
about the functionality, see "7.4.1 Main
Fine-tune with slope and
offset:
Slope Offset
↓ ↑
↑ ↓
↑ ↓
— ↓
Fine-tune with
setpoints:
(a) (a) (a) (a)
Y2 Y1 X1 X2
↑ — ↑ —
↓ — ↓ —
— ↑ — ↑
↑ ↑ ↑ ↑
↓ ↑ ↓ ↑
— ↓ — ↓
↑ ↓ ↑ ↓
↓ ↓ ↓ ↓
Description
condition. There is no
contacts: The used external
thermo ON/OFF
zone" [ 4 28].
ETBH/X12EF6V+9W
Daikin Altherma 3 H MT W
4P634879-1 – 2021.03