Page 1
O.S.B. Jay Ottoman Bed with IMPORTANT OTTOMAN SAFETY WARNINGS IMPORTANT – READ CAREFULLY – RETAIN FOR FUTURE REFERENCE You must ensure that the mattress is on the bed frame before operating the lift mechanism – Failure to do so could result in injury.
Page 2
Maximum storage height is 315mm . WARNING! HAZARD - DO NOT REACH INTO THE SPACE BELOW! Jay Ottoman Bed - Assembly guide - Page 2...
Page 3
Do not sit on the mattress whilst the platform is in motion or is in the raised position. o Users should only get in and out of bed when platform is in the flat (horizontal) position. Jay Ottoman Bed - Assembly guide - Page 3...
Thank You Dear Customer, Thank you for choosing to purchase your bed from Dreams - we hope it brings you your best ever night’s sleep. Before you begin building your bed, please take a moment to read through the instructions and make sure that you've got all the relevant parts listed on the following pages.
Angled Corner Brackets Ottoman support bar PACK (O.S.B.) Side Rail Cross Bar Ottoman support bar Fabric Base Cover Fixed retaining bracket - side rail Fabric Hand Strap Parking bracket - slat-frame 10 10 Jay Ottoman Bed - Assembly guide - Page 5...
Flat washer for M8 bolts ottoman support bar Spring washer for M8 bolts Tools required Q x1 P x1 Fixed retaining bracket Parking bracket - slat frame - side rail Tape measure Cross head screwdriver Jay Ottoman Bed - Assembly guide - Page 6...
Page 7
Double & King x1 Super King c x2 10mm a x2 10mm Fit both side rails to headboard & footboard, tighten all bolts 90%. & & Please do not tighten 100% yet. Jay Ottoman Bed - Assembly guide - Page 7...
Page 8
Slat Frame Support Bar Please make sure the cylinder (largest diameter) is at the top. Fit the piston stems to upper axles using lock nuts (h) - do not tighten yet. Jay Ottoman Bed - Assembly guide - Page 8...
Page 9
Using two nut sets on each side (i, b & c), connect the threaded studs loosely to the bars. Please do not tighten 100% yet. Jay Ottoman Bed - Assembly guide - Page 9...
Page 10
(i, b & c), one set at each end. Using one more nut set on each side (i, b & c), fix the second pair of studs loosely to the support bars. Please do not tighten 100% yet. Jay Ottoman Bed - Assembly guide - Page 10...
Page 11
Make sure the bed is still square and there is an even gap all round as in the sketch. Finally, on the support bar studs, tighten all eight nut sets 100% using tube spanner (q). Jay Ottoman Bed - Assembly guide - Page 11...
Page 12
Tighten them with tube spanner (q) but note, a small 2mm gap is needed so stems can move freely - this is important so do not over-tighten - see sketch --> Fit the fabric hand strap as shown. k x2 Jay Ottoman Bed - Assembly guide - Page 12...
Page 13
O.S.B stem just touches the surface - better to do this AFTER the mattress is fitted. Jay Ottoman Bed - Assembly guide - Page 13...
Page 14
Set the inner stem to the correct length so the end just touches the retaining bracket - it needs to touch to hold it in position. 100% Adjust the retaining bracket (P) so the stem end scrapes the surface. Jay Ottoman Bed - Assembly guide - Page 14...
Page 15
Using four bolt sets (a, b & c) fit the cross bar (G) to both side rails (C&D). Tighten 100% using Allen key (d). Take care not to damage the fabric when fitting. c x2 b x2 a x2 Jay Ottoman Bed - Assembly guide - Page 15...
Metal tends to be more resilient to everyday wear and tear. We recommend to gently dust your metal furniture and keep it dry to maintain its look. Thank you for shopping with us - we hope you have a great night's sleep. Jay Ottoman Bed - Assembly guide - Page 16...
Page 17
Little dreamers Keep the little ones entertained while you assemble your new purchase.
Need help?
Do you have a question about the Jay and is the answer not in the manual?
Questions and answers