Contents Introduction..............2 Transportation, storage and disposal......21 Safety................5 Technical data.............. 23 Assembly..............12 Accessories ..............24 Operation..............14 Declaration of Conformity..........25 Maintenance..............18 ..................27 Troubleshooting............21 Appendix ..............32 Introduction Product description Note: National or local regulations can set limit to the operation of the product.
Page 4
Read the operator's manual carefully and make sure that you understand the instructions before use. Use approved protective gloves. Use a protective helmet in locations where objects can fall on you. Use approved hearing protection and approved eye protection. Use heavy-duty slip-resistant boots. Maximum speed of the output shaft.
Safety Safety definitions Safety instructions for assembly Warnings, cautions and notes are used to point out WARNING: Read the warning specially important parts of the manual. instructions that follow before you use the product. WARNING: Used if there is a risk of injury or death for the operator or bystanders •...
Page 6
• Never allow children to use or be in the vicinity of the product. As the product is equipped with a spring- loaded start/stop switch and can be started by low speed and force on the starter handle, even small children under some circumstances can produce the force necessary to start the product.
Page 7
Always use approved personal protective equipment devices regularly. If the safety devices are damaged, when you use the product. Personal protective speak to your Husqvarna service agent. equipment cannot fully prevent injury but it • Do not make changes to safety devices. Do not...
Page 8
1. Push the throttle trigger lockout (A) and make sure 2. Move the stop switch to the stop position and make that the throttle control is released (B). sure that the engine stops. 2. Release the throttle trigger lockout and make sure To do a check of the cutting attachment guard that the throttle control is locked at idle speed.
Page 9
Return the product to too hot and this causes damage to the a Husqvarna dealer/service station if the cylinder and piston. muffler is damaged. WARNING:...
Page 10
To attach and remove the locknut WARNING: Stop the engine, use protective gloves and be careful around the sharp edges of the cutting attachment. A locknut is used to attach some types of cutting attachments. The locknut has a left thread. •...
Page 11
Make sure there are sufficient airflow when refueling agent do all other servicing. and mixing fuel (petrol and two-stroke oil) or draining • Let an approved Husqvarna service agent do the fuel tank. servicing on the product regularly. • Fuel and fuel vapor are highly flammable and can •...
Assembly Introduction 3. Tighten the screws. WARNING: Read and understand the safety chapter before you assemble the product. To assemble the loop handle 1. Put the loop handle on the shaft below the arrow. To install the cutting attachment guard and the grass blade 1.
Page 13
5. Make sure that the drive disc and support flange 4. Install the drive disc (D) on the output shaft. engages correctly in the center hole of the grass blade. 6. Attach the nut (G). 7. Tighten the nut with the socket wrench. Hold the shaft of the socket wrench near the cutting 5.
1 month at a time. two-stroke oil. • If Husqvarna two-stroke oil is not available, use a To fill the fuel tank two-stroke oil of good quality for air-cooled engines. Speak to your servicing dealer to select the correct 1.
Page 15
• Make sure that the locking force on the locknut is not decreased. The locknut must have a locking force at a minimum of 1.5 Nm. The tightening torque of the locknut must be between 35-50 Nm. CAUTION: • Examine the blade guard for damages or cracks. Contamination in the tanks Replace the blade guard if it has been hit or if it has causes malfunction.
Page 16
2. Move the choke control up into choke position. Note: If the engine stops, do the procedure again. About the surface WARNING: Do not put parts of your body in the grey marked area. If you touch the grey marked area it can result in burns to the skin.
Page 17
4. Cut with the left side of the grass blade. To clear grass 1. Keep the trimmer head above the ground. 2. Tilt the trimmer head. 3. Cut with the end of the trimmer line around objects in the work area. CAUTION: Cut grass.
the handles. Also do a check of the other WARNING: Clean the trimmer head parts of the trimmer head and clean it if cover each time you assemble new trimmer necessary. line to prevent unbalance and vibrations in Maintenance Introduction Note: The user must only carry out the maintenance and service work described in this operator's manual.
Page 19
Check and clean the spark arrestor mesh on the muffler (only applies to mufflers without a catalytic converter). To adjust the idle speed To clean the air filter Your Husqvarna product is designed and made to CAUTION: A air filter that is damaged, specifications that decrease harmful emissions.
Page 20
Use a single-cut flat file. 5. If the grease level is too low fill the bevel gear with Husqvarna bevel gear grease. Fill slowly and turn the drive shaft as you apply the bevel gear grease, stop at the correct level (B).
Troubleshooting Starting failure Check Possible cause Solution Stop button Stop position Set the stop switch to the start position. Starter pawls Binding pawls Adjust or replace the pawls. Clean around the pawls. Speak to an approved servicing dealer. Fuel tank Incorrect fuel Drain it and use correct fuel.
Page 22
Discard all chemicals, such as oil or fuel, at a service center or at an applicable disposal location. • When the product is no longer in use, send it to a Husqvarna dealer or discard it at a recycling location. 1999 - 001 - 14.06.2023...
Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Brush cutter Brand Husqvarna Type / Model 535RJ Identification Serial numbers dating from 2022 and onwards...
Page 26
UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Brush cutter Brand Husqvarna Type / Model 535RJ Identification Serial numbers dating from 2022 and onwards complies fully with the following UK regulations:...