Husqvarna 325CX Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 325c X Series
  6. Operator's manual
Husqvarna 325CX Operator's Manual

Husqvarna 325CX Operator's Manual

Hide thumbs Also See for 325CX:
Table of Contents

Advertisement

Quick Links

Oper ator's manual (EPA)
323L 325CX
Please r ead the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 325CX and is the answer not in the manual?

Questions and answers

Related Manuals for Husqvarna 325CX

Summary of Contents for Husqvarna 325CX

  • Page 1 Oper ator’s manual (EPA) 323L 325CX Please r ead the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    KEY TO SYMBOLS Symbols WARNING! Clearing saws, brushcutters Only intended for trimmer heads. and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’s manual.

  • Page 3: Table Of Contents

    CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Please read the operator’s manual carefully. Symbols ............... Maintenance, replacement, or repair of the emission control CONTENTS devices and system may be performed by any nonroad Contents ..............engine repair establishment or individual. Note the following before starting: ........

  • Page 4: Introduction

    Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.

  • Page 5: What Is What

    WHAT IS WHAT? What is what? 1 Trimmer head 13 Choke control 2 Grease filler cap, bevel gear 14 Air purge 3 Bevel gear 15 Air filter cover 4 Cutting attachment guard 16 Handle adjustment 5 Shaft 17 Shaft coupling 6 Loop handle 18 Operator’s manual 7 Throttle control...

  • Page 6: General Safety Precautions

    GENERAL SAFETY PRECAUTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! The machine is only designed for trimming grass. A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or The only accessories you can operate with this engine unit fatal injury to the operator or others.

  • Page 7: Machine's Safety Equipment

    GENERAL SAFETY PRECAUTIONS CLOTHING Make sure the throttle control is locked at the idle setting when the throttle lockout is released. Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants.
  • Page 8 GENERAL SAFETY PRECAUTIONS Cutting attachment guard Regularly check the vibration damping units for cracks or deformation. Check that the vibration damping element is undamaged and securely attached. WARNING! Overexposure to vibration can This guard is intended to prevent loose objects from being lead to circulatory damage or nerve damage thrown towards the operator.

  • Page 9: Cutting Equipment

    GENERAL SAFETY PRECAUTIONS Cutting equipment If the muffler on your machine is fitted with a spark arrestor screen this must be cleaned regularly. A blocked screen will cause the engine to overheat and may lead to serious This section describes how to choose and maintain your damage.

  • Page 10: Assembly

    ASSEMBLY Fitting the loop handle Assembling the cutting equipment (325Cx) WARNING! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole • Position the handle on the shaft. Note that the handle of the cutting attachment.

  • Page 11: Fitting Other Guards And Cutting Attachments

    35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool trimmer head kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in (325Cx) the opposite direction to the direction of rotation (Caution! left-hand thread). Guard •...

  • Page 12: Fuel Handling

    • In order to prevent unintentional starting of the engine, the • For best results and performance use HUSQVARNA two- spark plug cap must always be removed during long-term stroke engine oil, which is specially formulated for our air- storage, if the machine is not under close supervision and cooled two stroke-engines.

  • Page 13: Fueling

    FUEL HANDLING Mixing Fueling • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture.

  • Page 14: Starting And Stopping

    STARTING AND STOPPING Check before starting Starting and stopping • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most WARNING! The complete clutch cover and common reason why cracks are formed is that sharp shaft must be fitted before the machine is corners have been formed at the bottom of the teeth while started, otherwise the clutch can come loose...
  • Page 15 STARTING AND STOPPING CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. CAUTION! Do not put any part of your body in marked area. Contact can result in burns to the skin, or electrical shock if the spark plug cap has been damaged.

  • Page 16: Working Techniques

    WORKING TECHNIQUES General working instructions 6 Always hold the machine with both hands. Hold the machine on the right side of your body. IMPORTANT! This section takes up the basic safety precautions for working with a trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert.

  • Page 17: Grass Trimming With A Trimmer Head

    WORKING TECHNIQUES Grass trimming with a trimmer head Sweeping • The fan effect of the rotating cord can be used for quick and easy clearing up. Hold the cord parallel to and above the area to be swept and move the tool to and fro. Trimming •...

  • Page 18: Maintenance

    CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops. Your Husqvarna product has been designed and manufactured to specifications that reduce harmful Rec. idle speed 2700 rpm emissions.

  • Page 19: Muffler

    MAINTENANCE Correctly adjusted carburetor will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts When the carburetor is correctly adjusted the machine will to rotate. accelerate without hesitation and burble a little at maximum speed.

  • Page 20: Cooling System

    • A dirty air filter. Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The These factors cause deposits on the spark plug electrodes, filter oil contains a solvent to make it spread evenly through which may result in operating problems and starting the filter.

  • Page 21: Bevel Gear

    The grease in the bevel gear does not normally need to be changed except if repairs are carried out. CAUTION! Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically...

  • Page 22: Maintenance Schedule

    MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily Weekly Monthly Maintenance maintenance maintenance maintenance Clean the outside of the machine. Make sure the throttle trigger lock and the throttle function correctly from a safety point of view.

  • Page 23: Technical Data

    TECHNICAL DATA Technical data 323L 323L (USA) 325Cx Engine Cylinder displacement, cu.in/cm 1,50/24,5 1,50/24,5 1,50/24,5 Cylinder bore, inch/mm 1,34/34,0 1,34/34,0 1,34/34,0 Stroke, inch/mm 1,06/27 1,06/27 1,06/27 Idle speed, rpm 2700 2700 2700 Recommended max. fast idle speed, rpm 11000-11700 11000-11700...
  • Page 24 Cutting attachment guard, Powerhead model Accessories Type Art. no. Blade shaft thread 3/8 R Trimmy Fix 3/8” (R) 537 18 96-03 325Cx Trimmer head T25 (R) 537 18 96-03 T25C (R) 537 18 96-03 Arbor shaft thread M10 Plastic blades Tricut Ø...

  • Page 25: Federal And California Emissions Control Warranty Statement

    COVERAGE by Husqvarna Forest & Garden at no cost. Any such part repaired or replaced under warranty is warranted for the The emissions control system is warranted for two years. If remainder of the period prior to the first scheduled...
  • Page 26 EPA may not be used. The use of any non-exempted add-on or modified parts will be grounds for disallowing a warranty claim. Husqvarna Forest & Garden will not be liable to warrant failures of warranted parts caused by the use of a non- exempted add-on or modified part.
  • Page 27 Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...
  • Page 29 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
  • Page 30 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
  • Page 31 T35, T35x 8,5 m 10 cm 4" 4,3 m "Clic" 15 cm 6"...
  • Page 32 6,0 m 10 cm 4" 3,05 m "Clic" 15 cm 6"...
  • Page 33 T25C 2,75 m 2,75 m 15 cm 6"...
  • Page 34 T25C 2,75 m x 2 9' x 2 2,75 m 2,75 m "Clic" 15 cm 6" ´®z+R9o¶5;¨ ´®z+R9o¶5;¨...
  • Page 36 1155648-95 2013-03-18...

This manual is also suitable for:

323lPrestige327ld535ls

Table of Contents