Battery Disposal Warning - Hoover STREAMLINE User Manual

LUBRICATION: The motor is equipped with
bearings which contain sufficient lubrication for
their lifetime. The addition of lubricant could
cause damage. Do not add lubricant to motor
bearings.
THERMAL PROTECTION
A thermal protector has been designed into your
cleaner to protect it from overheating. When the
thermal protector activates the cleaner will stop
running. If this happens proceed as follows:
1. Turn cleaner OFF (and unplug from outlet).
2. Empty dirty water tank.
3. Inspect the nozzle for any obstructions.
Clear obstructions if present.
4. When cleaner is de-energized and motor
cools for 30 minutes, the thermal protector
will deactivate and cleaning may continue.
If the thermal protector continues to activate
after following the above steps, your cleaner
needs servicing.
BATTERY DISPOSAL
WARNING
- RISK OF EXPLOSION OR
EXPOSURE TO TOXIC MATERIAL.
LITHIUM-ION BATTERIES
The battery must be collected, recycled or
disposed of in an environmentally sound
manner. The EPA certified RBRC Battery
Recycling Seal on the lithium-ion (Li-ion)
battery indicated Techtronic Industries, a
corporate affiliate of Hoover, Inc., is voluntarily
participating in an industry program to collect
and recycle these batteries at the end of
their useful life, when taken out of service
in the United States or Canada. The RBRC
program provides a convenient alternative to
placing used Li-ion batteries into the trash or
the municipal waste stream, which may be
illegal in your area. Please visit www.rbrc.org/
call2recycle/ for information on Li-ion battery
recycling and disposal bans/restrictions in
your area. Hoover, Inc.,
involvement in this program
is part of our commitment to
preserving our environment
and conserving our natural
resources.
PRODUCT SET-UP
1
Place self-clean tray in a storage area for
placement of the unit after use. Ensure this is
near an outlet to allow the plug-in of the tray for
charging. Use tray for the self-cleaning function.
"Click"
2
Attach handle onto body of the unit, proper
installation will result in a clicking sound.
3
To insert the ONEPWR battery press the button to
release the dock.
4
Slide the ONEPWR battery into the dock until it
clicks and push the battery forward until it clicks.
BATTERY CHARGING
5
To charge your ONEPWR battery while in unit,
place the unit directly down onto the self-
cleaning tray and ensure the tray is plugged in.
*Battery must be charged prior to initial use
FILLING THE SOLUTION
TANK
WARNING:
To reduce risk of injury
from moving parts, remove the battery before
servicing. Do not use cleaner without tank in
place.
1
Remove the clean water tank from the back of the
unit by pressing down the button and pulling out.
2
Pull back the tab to access fill hole.
2
3
First fill with warm water to appropriate water
line. Secondly, add solution to solution line.
NOTE: Flap must be clicked in place for proper
performance and to prevent leaking.
NOTE: Read the directions on the Hoover Hard
Floor solution prior to use.
CLEANING FLUID: SEE THE HOOVER SOLUTION
GUIDE insert or visit Hoover.com/cleaning-
solutions.
4
Close tab and put clean water tank back into
the unit.
OPERATION
CAUTION:
To prevent damage to
wood floors, follow the flooring manufacturer's
cleaning recommendations. If using cleaner on
sealed wood floors, inspect floor surface for
worn finish, bare wood or separated joints. Do
not use to clean sealed wood floors if any of
these conditions exist.
IMPORTANT: check for worn spots or joint
separations before using, as these conditions
could lead to damaged flooring when using water
to clean floor.
CAUTION:
Do not clean over floor
electrical outlets.
CAUTION:
Do not use the cleaner to
pick up flammable or combustible liquids or
chemicals.
1
Recline by placing a foot gently on the floor head
of the unit and pull the handle backwards.