Do you have a question about the MRY7940 and is the answer not in the manual?
Questions and answers
Mary
February 23, 2025
How do you attach the furniture cleaning piece
1 comments:
Mr. Anderson
February 23, 2025
To attach the furniture cleaning piece to the Royal MRY7940, follow these steps:
1. Open the port on the top of the unit. 2. Insert the hose into the port, aligning the two small knobs on the hose with the corresponding slots. 3. Twist the hose to lock it into place. 4. Connect the solution hose by plugging it into the hose solution tube until it clicks into place.
This setup allows the shampoo and water to flow properly for furniture cleaning.
This answer is automatically generated
Natalie
February 22, 2025
I have followed all operating instructions and searched through troubleshooting guide but no liquid is being released onto carpet. Trigger depressed or not, it’s dry and the lower tank is not filling.
1 comments:
Mr. Anderson
February 22, 2025
Possible causes for the Royal MRY7940 not releasing liquid onto the carpet despite following operating instructions could include:
1. Soap Switch Turned Off – The machine has a switch to turn the soap off for a rinse cycle. Ensure this switch is turned on if using carpet shampoo. 2. Solution Hose Not Connected Properly – The solution hose, which allows shampoo and water to come out, must be securely plugged into the hose solution tube. 3. Clogged or Blocked Tubes – Check for any clogging in the hose or solution tube that may prevent liquid flow. 4. Empty or Improperly Filled Tank – Ensure the water and shampoo tanks are filled correctly. 5. Faulty Pump or Valve – If the machine still does not release liquid, there may be an issue with the internal pump or valve.
Checking these factors should help resolve the issue.
This answer is automatically generated
Diane Erickson
August 9, 2025
This is model number RY7910. Is it the same as MRY7940?
John Meeke
June 23, 2025
Is there a clean water tank available for the royal carpet cleaner for model MRY7910041300003037
Peggy Obrien
April 14, 2025
we lost the cap that goes on the dirty water reseviour . is there one we can buy that will fit and what is the size to use. thanks
Donnie Harrelson
March 2, 2025
How do you take the clear brush cover head apart? There are six Phillips Screws but when I removed them the cover did not separate. There is debris inside the cover that I cannot flush out so it would like it cleaned. Thank you!
Need help?
Do you have a question about the MRY7940 and is the answer not in the manual?
Questions and answers
How do you attach the furniture cleaning piece
To attach the furniture cleaning piece to the Royal MRY7940, follow these steps:
1. Open the port on the top of the unit.
2. Insert the hose into the port, aligning the two small knobs on the hose with the corresponding slots.
3. Twist the hose to lock it into place.
4. Connect the solution hose by plugging it into the hose solution tube until it clicks into place.
This setup allows the shampoo and water to flow properly for furniture cleaning.
This answer is automatically generated
I have followed all operating instructions and searched through troubleshooting guide but no liquid is being released onto carpet. Trigger depressed or not, it’s dry and the lower tank is not filling.
Possible causes for the Royal MRY7940 not releasing liquid onto the carpet despite following operating instructions could include:
1. Soap Switch Turned Off – The machine has a switch to turn the soap off for a rinse cycle. Ensure this switch is turned on if using carpet shampoo.
2. Solution Hose Not Connected Properly – The solution hose, which allows shampoo and water to come out, must be securely plugged into the hose solution tube.
3. Clogged or Blocked Tubes – Check for any clogging in the hose or solution tube that may prevent liquid flow.
4. Empty or Improperly Filled Tank – Ensure the water and shampoo tanks are filled correctly.
5. Faulty Pump or Valve – If the machine still does not release liquid, there may be an issue with the internal pump or valve.
Checking these factors should help resolve the issue.
This answer is automatically generated
This is model number RY7910. Is it the same as MRY7940?
Is there a clean water tank available for the royal carpet cleaner for model MRY7910041300003037
we lost the cap that goes on the dirty water reseviour . is there one we can buy that will fit and what is the size to use. thanks
How do you take the clear brush cover head apart? There are six Phillips Screws but when I removed them the cover did not separate. There is debris inside the cover that I cannot flush out so it would like it cleaned. Thank you!