Bosch Professional GCM 10 GDJ Original Instructions Manual page 27

OBJ_BUCH-1923-002.book Page 27 Monday, November 16, 2015 3:44 PM
– Adjust a vertical bevel angle, retighten lock lever 14 and
check if the desired clamping force has been reached.
Transport (see figure W)
Before transporting the power tool, the following steps must
be carried out:
– Slide glide arm 23 completely to the rear and secure it in
this position (see "Securing the Glide Arm", page 22).
– Make sure that the depth stop 25 is pushed completely in-
ward and that adjusting screw 24 fits through the recess
without touching the depth stop when moving the glide
arm.
– Guide the glide arm downward until transport safety-lock
26 can be pushed completely inward.
– Slide the extensions bars 16 completely inward.
– Set the vertical bevel angle to 0° and tighten the lock lever
14.
– Turn saw table 33 leftward to the stop and tighten locking
knob 12.
– Wind up the mains cable and tie it together with Velcro
strap 63.
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– Carry the machine by the transport handle 64 or hold it by
the recessed handles 17 on the sides of the saw table.
 When transporting the power tool, only use the trans-
port fixtures. Never carry the power tool by the protec-
tive devices, the glide arm 23 or the handle 3.
 The power tool should always be carried by two per-
sons in order to avoid back injuries.
Maintenance and Service
Maintenance and Cleaning
 Before any work on the machine itself, pull the mains
plug.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Cleaning
For safe and proper working, always keep the power tool and
its ventilation slots clean.
The retracting blade guard must always be able to move freely
and retract automatically. Therefore, always keep the area
around the retracting blade guard clean.
– Remove dust and chips after each working procedure by
blowing out with compressed air or with a brush.
– Clean the roller 20 and the glide arm 23 regularly.
Bosch Power Tools
Accessories
Material clamp
Insert plates
Dust bag
Extraction adapter
Saw blades for wood and plate materials, panels and
strips/mouldings
Saw blade 254 x 25.4 mm, 40 teeth
Saw blades for hardwood, composite materials, plastic
and non-ferrous metals
Saw blade 254 x 25.4 mm, 80 teeth
Saw blade 254 x 25.4 mm, 96 teeth
Saw blade 254 x 25.4 mm, 120 teeth
After-sales Service and Application Service
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
People's Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 4008268484
Fax: (0571) 87774502
E-Mail: contact.ptcn@cn.bosch.com
www.bosch-pt.com.cn
HK and Macau Special Administrative Regions
Robert Bosch Hong Kong Co. Ltd.
21st Floor, 625 King's Road
North Point, Hong Kong
Customer Service Hotline: +852 2101 0235
Fax: +852 2590 9762
E-Mail: info@hk.bosch.com
www.bosch-pt.com.hk
Indonesia
PT. Multi Mayaka
Kawasan Industri Pulogadung
Jalan Rawa Gelam III No. 2
Jakarta 13930
Indonesia
Tel.: (021) 46832522
Fax: (021) 46828645/6823
E-Mail: sales@multimayaka.co.id
www.bosch-pt.co.id
English | 27
Article number
1 609 B02 125
1 609 B04 263
1 609 B04 264
1 609 B02 595
2 607 001 977
2 608 676 047
2 608 640 969
2 608 640 970
2 608 640 971
1 609 92A 1U5 | (16.11.15)