Table of Contents
Advertisement
Quick Links
Operating Instruction
and safety manual
IMPORTANT:
Please read and fully understand this manual for informa�on rela�ng to protec�ng your
safety and preven�ng equipment problems. And retain this manual for future reference.
1.Air Inlet Coupler
3. Exhaust cap
5. Nails
7.Magazine
9.Depth adjustment knob
11.Jam release
Angle Finish Nailer DA64R
34°Angle Finish Nailer
Model: DA64R
2. No-mar pad
4. Air Supply
6.Pusher
8.Trigger
10.Safety yoke
DESCRIPTION
Http://www.aeroprotools.com
1
Advertisement
Table of Contents
Related Manuals for Aeropro DA64R
Summary of Contents for Aeropro DA64R
- Page 1 And retain this manual for future reference. DESCRIPTION 1.Air Inlet Coupler 2. No-mar pad 3. Exhaust cap 4. Air Supply 5. Nails 6.Pusher 7.Magazine 8.Trigger 9.Depth adjustment knob 10.Safety yoke 11.Jam release Angle Finish Nailer DA64R Http://www.aeroprotools.com...
- Page 2 In special cases it is necessary to wear hearing protec�on equipment. INFORMATION ON MECHANICAL IMPACT (VIBRATION) Angle Finish Nailer DA64R Http://www.aeroprotools.com...
-
Page 3: Additional Safety Instructions For Pneumatic Power Tools
Take condi�ons at the workplace into account. Fasteners can penetrate thin work pieces or slip off corners and edges of workplaces, and thus put people at risk. For personal safety, use protec�ve equipment such ad hearing and eye protec�on. Fastener driving tools are operated by actua�ng the trigger using finger pressure. Angle Finish Nailer DA64R Http://www.aeroprotools.com... -
Page 4: Residual Risks
3. Danger of injury and property damage caused by flying objects. SYMBOLS SPECIFICATIONS FASTENER TOOL Magazine capacity 100pcs Air inlet size 1/4”(6.35mm) Air hose size 3/8”(9.52mm) Nail type Max working pressure 120PSI(8.3bar) Working pressure range 80-120PSI(5.5-8.3bar) Exhaust Rear adjustable(360°) Tool weight(no nails) 2.09kg(4.6lb) Angle Finish Nailer DA64R Http://www.aeroprotools.com... -
Page 5: Noise And Vibration
Check whether the fastener has been driven into the work piece in accordance with the requirements. If the fastener is protruding, increase the air pressure in increments of 0.5 bar, checking the result a�er each new adjustment; Angle Finish Nailer DA64R Http://www.aeroprotools.com... -
Page 6: General Maintenance
flow of air to the tool. REQUIRED DAILY CHECKLIST 1. Disconnect the air supply from the tool and remove all fasteners. Angle Finish Nailer DA64R Http://www.aeroprotools.com... -
Page 7: Troubleshooting
Install overhaul kit. Tool jams frequently. Incorrect fasteners. Verify that fasteners are the correct size. Damaged fasteners. Replace fasteners. Loose magazine. Tighten screws. Dirty magazine. Clean magazine. Worn or damaged driver. Install driver maintenance kit. Angle Finish Nailer DA64R Http://www.aeroprotools.com... - Page 8 pARts lIst Description Description Description Description Bolt Bumper Trigger valve guide Fixed cover Axle sleeve Cylinder cover washer Spring O-ring 9 x 1.8 Gun body O-ring 2.5 x 1.5 Retainer ring Air deflector Rubber washer Switch valve stem Drive nail slip Bolt M5 x 25 O-ring 1.7 x 2 O-ring 18 x 2.65...
Need help?
Do you have a question about the DA64R and is the answer not in the manual?
Questions and answers