Aeropro CN65RA Instruction Manual

Aeropro CN65RA Instruction Manual

Air-powered coil nailer

Advertisement

INSTRUCTION MANUAL

AIR-POWERED COIL NAILER
CN65RA
Residual Risks
Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors.
The following hazards may arise in connection with the tool's construction and design:
IMPORTANT:
Read all safety rules and operating Instructions
carefully before starting the product.
Keep this Manual for future reference.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CN65RA and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Aeropro CN65RA

  • Page 1: Instruction Manual

    INSTRUCTION MANUAL AIR-POWERED COIL NAILER CN65RA IMPORTANT: Read all safety rules and operating Instructions carefully before starting the product. Keep this Manual for future reference. Residual Risks Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors.
  • Page 2: Table Of Contents

    TABLE OF CONTENTS:  TECHNICAL SPECIFIACTIONS  SAFETY GUIDELINES  KEY PARTS DIAGRAM  IMPORTANT INFORMATION  TYPES OF FASTENERS  OPERATING INSTRUCTIONS  MAINTENANCE  TROUBLESHOOTING  EXPLODED VIEW  PARTS LIST  TECHNICAL SPECIFIACTIONS: Magazine capacity(QTY.) 250 nails (1 coil) 15º...
  • Page 3: Safety Guidelines

     SAFETY GUIDELINES This manual contains information that relates to protecting personal safety and preventing equipment problems.it is very important to read this manual carefully and understand it thoroughly before using the product. the symbols listed below are used to indicate this information DANGER! Potential hazard that will result in serious injury or loss of life.
  • Page 4 -Do not use the air tools unless you have been trained to do so. Only a qualified person should use the tool. -Locate the compressor in a well-ventilated area for cooling, and must be a minimum of 12”(31cm) away from the nearest wall.
  • Page 5: Key Parts Diagram

     KEY PARTS DIAGRAM  IMPORTANT INFORMATION Compatible compressors GUIDELINES FOR PROPER USE AND OPERATION Be sure to use a proper air compressor with air powered tools. General use The Air-Powered Coil Siding Nailer. drives 1-1/2” to 2-1/2” 0º plactic coil nails. The tool is lightweight and durable, stands up to the elements and provides consistently accurate results over the life of the tool.
  • Page 6: Types Of Fasteners

     Verify that all of the connections in the air supply system are sealed in order to prevent air from leaking. Description Description Description AEROPRO Air powered coil nailer Air Hose Filter Quick connector Lubricator Cut-off valve Quick coupler Regulator(0 to 8.3 Bar)
  • Page 7: Operating Instructions

     OPERATING INSTRUCTIONS  LOADING NAILS 1. Disconnect the tool from the air supply. 2. Press the knob down and swing the nail guide open; open the magazine cover. 3. Adjust the position of the nail holder according to the nail length. The nail will not feed smoothly if the nail holder is not correctly adjusted.
  • Page 8 5.①Uncoil enough nails to reach the driving hole; ② Insert the first nail into the driving hole and the second nail between the two pawls of the feeder. ③ Fit the nail heads in the guide slot ④ Pulling the nails to the right, swing the nail guide closed. NOTE: Be careful not to deform the collated wires and not to disengage the nails with the guide surface.
  • Page 9  Testing the nailer Before actually beginning the nailing work, test the nailer by using the check list below. Conduct the tests in the following order. If abnormal operation occurs, stop using the nailer and contact a service centre immediately. DISCONNECT AIR HOSE FROM NAILER.
  • Page 10 5. With the nailer off the workpiece, pull the trigger. Depress the push lever against the workpiece.  THE NAILER MUST OPERATE. 6. If no abnormal operation is observed, you may load nails in the nailer. Drive nails into a test piece that is the same type of material that will be used in the actual application.
  • Page 11  ADJUSTING THE NAILING DEPTH To assure that each nail penetrates to the same depth,be sure that: ⑵ the air pressure to the Nailer remains constant(regulator is installed and working properly),and ⑵ the Nailer is always held firmly against the workpiece. Adjust the nailing in the following order. ①...
  • Page 12  Clearing a jammed nail  Disconnect the tool from the air supply line.  Open the nail guide and insert a rod into the outlet. Tap the rod with a hammer.  Remove the jammed nail with a slotted screwdriver. ...
  • Page 13: Troubleshooting

     TROUBLESHOOTING (See Table 1) The following chart lists common operating system issues and solutions.please read it carefully and follow all instructions closely. DANGER! Potential hazard that could result in serious injury or loss of life. If any of the following symptoms appear while the tool is in use,turn it off and disconnect it from the air supply immediately.
  • Page 14: Exploded View

    EXPLODED VIEW 2017.10.10 ( A0 ) CN65RA 48 49 39 40 41 82 76 83 76 77 78...
  • Page 15: Parts List

     PARTS LIST K-3 Code Description Qty. K-3 Code Description Qty. 03.04.23.073 Hex. Socket 03.04.01.060 O-ring 9*1.8 03.04.21.031-01 Top Cover 03.04.34.043 Swtich spring Hex. Socket HD. Bolt 03.04.05.407 03.04.15.043 Trigger Plunger M5x30 Hex. Socket HD. Bolt 03.04.05.070 03.04.01.032 O-ring 2.4*1.6 M5x10 03.04.28.032 Exhaust Cover...
  • Page 16 03.04.02.105 Safety Guard 03.04.31.138 03.04.03.031 Trigger 03.04.34.089 Ratchet Spring 03.04.05.186 pin 2.5*16 03.04.40.098 Holder Cap 03.04.40.047 Shift knob 03.04.40.097 Nail Holder 03.04.05.189 pin 3*10 03.04.40.099 Magazine Cover 03.04.36.097 Spring 03.04.05.190 Roll Pin 3*12 03.04.40.130 steel ball DW=4 03.04.15.079 Holder Shaft 03.04.05.197 pin 3*30 03.04.29.222...

Table of Contents