Table of Contents
Advertisement
Quick Links
OPERATING INSTRUCTIONS FOR FASTENER DRIVING
TOOLS OPERATED BY COMPRESSED AIR
Residual risks
Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. The
following hazards may arise in connection with the tool's construction and design:
Damage to lungs if an effective dust mask is not worn.
Damage to hearing if effective hearing protection is not worn.
Health defects resulting from vibration emission if the power tool is being used over longer period of
time or not adequately managed and properly maintained.
Wear eye protection.
1
Air Finish nailer LT50
Air Nailer (Finish Nailer)
Model No.: LT50
IMPORTANT:
Read all safety rules and operating
Instructions carefully before first use it.
Keep this Manual for future reference.
2013
2014
Http://www.aeroprotools.com
Advertisement
Table of Contents
Related Manuals for Aeropro LT50
Summary of Contents for Aeropro LT50
- Page 1 Damage to hearing if effective hearing protection is not worn. Health defects resulting from vibration emission if the power tool is being used over longer period of time or not adequately managed and properly maintained. Wear eye protection. 2013 2014 Air Finish nailer LT50 Http://www.aeroprotools.com...
-
Page 2: Table Of Contents
2.4 Safety of fastener driving tool 7 explode drawing 2.5 Safety at work 8 Spare parts list 2.6 Triggering devices 1 Technical data Type of tool ……………………………………………………………… LT50 Activation mode ………………………………………………………single sequential Outline dimension……………………………………………………………80x280x303mm Weight (without fasteners)………………………………………………...2.3kgs (5.06Lb) Required pressure………………………………………………………….70-110PSI (4.8-7.5bar) Max. pressure………………………………………………………………..120PSI (8.3bar) Recommended lubricant………………………………………………….white mineral oil 10＃... - Page 3 CEN-and CENELEC-standards),to be able to assess the safe working condition of fastener driving tools. Air Finish nailer LT50 Http://www.aeroprotools.com...
- Page 4 Hold the fastener driving tool during the work operation in such a way that no injuries can be caused to the head or to the body in the event of possible recoil consequent upon a disruption in the energy supply or hard areas within the workplace.（see fig 2） Air Finish nailer LT50 Http://www.aeroprotools.com...
-
Page 5: Actuating Systems
Colours: Red on white ground, fastener driving tools and ladder black Fig. 4: Symbol” Do not use on scaffoldings, ladders” Air Finish nailer LT50 Http://www.aeroprotools.com... -
Page 6: Compressed Air System
We therefore recommend that 2to 5drops (depending on the loading of the fastener driving tool)of the recommended oil (see TECHNICAL DATA) should be added via the air inlet of the tool, or an oiler attached directly to the fastener driving tool. (see fig 5) Air Finish nailer LT50 Http://www.aeroprotools.com... -
Page 7: Preparing The Tool For Use
The compressed air connectors of the fastener driving tool and the hoses should be protected against contamination, the ingress of coarse dust chips, sand etc, will result in leaks and damage to the fastener driving tool and the couplings. Air Finish nailer LT50 Http://www.aeroprotools.com... -
Page 8: Maintenance
1. Change and use correct fastener. 2. Damaged or worn driver guide. 2. Check and replace the driver. 3. Magazine or nose screw loose. 3. Tighten the magazine. 4. Magazine is dirty. 4. Clean the magazine. Air Finish nailer LT50 Http://www.aeroprotools.com... -
Page 9: Explode Drawing
7. Explode Drawing Air Finish nailer LT50 Http://www.aeroprotools.com... -
Page 10: Spare Parts List
Air inlet plug cover Spring Washer 6 Pin A4*20 O-ring 1.9*1.1 Note: if you need spare parts of this model, please feel free to contact us or the distributor where you bought this tool. Thanks! Air Finish nailer LT50 Http://www.aeroprotools.com...
Need help?
Do you have a question about the LT50 and is the answer not in the manual?
Questions and answers