Advertisement
Quick Links
Models:
57550 – Buffer
57551 – Mini Orbital Sander
57552 – 3-1/2" Disc Sander
57553 – Versatility Kit
57555 – 4"-5" Disc Sander
WARNING
!
57054 Rear Ring
01206 Bearing
57056 Rear Bearing Plate
95971 Line-up Pin
57058 Cylinder Assembly
(Includes 95971 Line-up Pin)
54491 Blade (5) and
O
Rotor set
95975 Shim Pack
(4 pkg./as req.)
56047 Rotor Key
54470 Rotor Pinion
57437 Front Bearing Plate
57055 Front Ring
95973 Washer
T
57059 Lock Ring Seal
3
01139 Bearing
07146 Packing
01139 Bearing
54475 Shaft (2)
06213 Gears (2)
54465 Planetary Carrier
54468 Ring Gear
54467 Retaining Ring
95593 Set Screw
01139 Bearing
54021 Adapter
Oil
O
Loctite/Hernon: L
L
Torque: N•m x 8.85 = In. - lbs.
T
T
= 22.5 N•m, T
2
Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools
(ANSI B186.1) and any other applicable safety codes and regulations. Please refer to Dynabrade's
Warning/Safety Operating Instructions for more complete safety information.
95979 Pin
57547 Lever
57526 Housing
95697 Snap Ring
01025 O-Ring (2)
01477 Valve Stem
57064 Speed Regulator
See inside for Important Operating, Maintenance and Safety Instructions.
KEY
Grease
G
= Loctite #271
2
Buffer/Sander
= 28 N•m
3
54476 Mini-Orbital Head
Mini-Orbital Sanding Pads
(See page 4.)
Parts Page Reorder No. PD 97•12
Effective March, 1997
Supercedes PD95•06
Palm-Style
Air-Powered, 2,400 RPM
57065 Cone Muffler
56027 Muffler Insert
57066 Muffler Body
01464 Seal
01494 Inlet Bushing
01472 Tip Valve
01468 Spring
3" – 50125 Pad
3" – 50120 Pad
4" - 5" – 50146 Pad
(See page 4 for
descriptions.)
3-1/2" Sanding Pad
54486 "Soft" Vinyl Face
54488 "Soft" Hook Face
56028 Muffler Cap
T
L
2
2
Advertisement
Related Manuals for Dynabrade 57550
Summary of Contents for Dynabrade 57550
- Page 1 Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools WARNING (ANSI B186.1) and any other applicable safety codes and regulations. Please refer to Dynabrade's Warning/Safety Operating Instructions for more complete safety information.
- Page 2 2. Some silencers on air tools may clog with use. Clean and replace as required. 3. All Dynabrade air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example : if the tool specification state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute).
- Page 3 Important: Motor should now be tested for proper operation at 90 PSI. If motor does not operate properly or operates at a higher RPM than marked on the tool, the tool should be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed.
- Page 4 Visit our new Web Site via Industry.Net MROP On-Line: http://www.dynabrade.industry.net E-Mail: DynaTalk@aol.com DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524 DYNABRADE EUROPE S.àr.l., Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 • Fax: 352 76 84 95 ©...
Need help?
Do you have a question about the 57550 and is the answer not in the manual?
Questions and answers