Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dovre 225MF
Summary of Contents for Dovre 225MF
- Page 1 INSTALLATION INSTRUCTIONS AND OPERATING MANUAL STOVE 225MF 03.27125.000 06/2013...
-
Page 2: Table Of Contents
Removing ashes Fog and mist Solving problems Maintenance Chimney Cleaning and other regular maintenance acti- vities Exchange parts 225MF Appendix 1: Technical Data Appendix 2: Dimensions Appendix 3: Distance from combustible material Appendix 4: Diagnosis diagram Index Subject to change because of technical improvements... -
Page 3: Introduction
The appliance is intended for use in a living room. It should be connected hermetically to a well-func- tioning chimney. that the 225MF wood stove has been produced in We advise you have the appliance installed by an accordance with EN 13240. -
Page 4: Safety
Safety Installation requirements Please note: All safety regulations must be complied with strictly. General Please read carefully the instructions supplied with the appliance for installation, use and The appliance must be connected tightly to a well- maintenance, before using the appliance. functioning chimney. -
Page 5: Ventilation Of The Area
Starting from the flue spigot, the flue must run as Ventilation of the area vertically as possible. Changes in direction and horizontal pieces disrupt the outward flow of com- For good combustion, the stove needs air (oxygen). bustion gases and may cause soot deposits. This air is supplied via adjustable air inlets from the area in which the stove is installed. -
Page 6: Product Description
material. Features of the appliance The rule of thumb for a single-walled tube is a distance of 3x the diameter. If a lining shell is The appliance is an entirely cast-iron design with fitted around the tube, a distance of 1x the dia- modern combustion technology. - Page 7 Chamotte inner plates are ochrous on deli- very. They insulate the combustion cham- ber, improving combustion and they can withstand burning anthracite coals. 1. Open the door; see the following figure. 09.20020.101 Removable internal sections 2 grid holder 3 fire basket 4 inner plate on the left and right side 5 baffle plate 6 grate...
-
Page 8: Preparing The Outside Air Connection
Because of the distance to the (combustible) wall, the protection plate may not be removed in the back shield. 1. Apply supplied fibre glass sealing tape (3) mea- suring 10 x 3 mm to the contact surface of the con- nection collar (2). 2. -
Page 9: Installing And Connecting
Fuel start burning brown coal briquettes. For lighting the fireplace, follow the instructions in The appliance 225MF is a multi fuel stove.. This stove the "Lighting" paragraph. is suitable for burning natural wood; sawn and split wood that is sufficiently dry. The appliance is also suit-... -
Page 10: Lighting
Preferably use category A anthracite coal with a low ash content. Use the recommended size 12/22 or 20/30. For lighting the fireplace, follow the instructions in the "Lighting" paragraph. Lighting You can check whether the flue has sufficient draught by lighting a ball of paper above the baffle plate. A cold flue often has insufficient draught and consequently, some smoke may escape into the room instead of up the chimney. -
Page 11: Burning Brown Coal Briquettes
1. Slowly open the stove door. Compact stacking 2. Spread the charcoal evenly across the bottom of the stove base. 3. Place the brown coal briquettes on the charcoal bed. 4. Close the door. 5. Regularly remove ashes from the stove base by riddling the grate. -
Page 12: Extinguishing The Fire
Control the air supply with the secondary air inlet. The secondary air inlet not only supplies air to the fire but to the glass as well, so that it does not quickly become dirty. Open the primary air inlet for the time being if the air supply by the secondary air inlet is inadequate or if you want to fan the fire. -
Page 13: Fog And Mist
Fog and mist Fog and mist hinder the flow of flue gases through the flue. Smoke can blow back and cause a stench. If it is not strictly necessary, it is better not to use the stove in foggy and misty weather. Solving problems Refer to the appendix "Diagnostic diagram"... - Page 14 Checking fire-resistant inner plates Maintenance enamelled stove The fire-resistant inner plates are consumables and Never clean the stove while it is still hot. The most subject to wear . Check the fire-resistant inner plates effective way to clean the enamelled surface of the frequently and replace them when necessary.
-
Page 15: Exchange Parts 225Mf
Check the appliance for air leaks. Close any chinks with stove sealant. Allow the sealant to harden fully before lighting the stove, as any moisture in the sealant will form bubbles, resulting in a new air leak. Exchange parts 225MF 09.20020.101 Pos. Part number Description Quantity 03.56332.000... -
Page 16: Appendix 1: Technical Data
Appendix 1: Technical Data Model 225MF 4.6kW Nominal output 4.6 kW Chimney connection (diameter) 125 mm Weight +/- 118 kg Brown coal bri- Anthracite Fuel Wood quettes coal Fuel property, max. length wood, max. for- 30 cm 3"-6"-7" 20-30 mat fuel Mass flow of flue gases 4.9 g/s... -
Page 17: Appendix 2: Dimensions
Appendix 2: Dimensions 225MF (GB) Subject to change because of technical improvements... -
Page 18: Appendix 3: Distance From Combustible Material
Appendix 3: Distance from combustible material 225MF - Minimal distance in millimetres 09-20008-017 Protective (insulated) connection pipe Combustible material Incombustible material, thickness 100 mm Please note! To guarantee the flow of combustion air, when no outside air connection is provided, the dis- tance from the outside air connection collar to the wall must be at least 20 mm. - Page 19 225MF - Dimensions of fireproof protective plate 09-20002-004 Minimal dimensions of fireproof protective plate A (mm) B (mm) Din 18891 Germany Finland Norway Subject to change because of technical improvements...
-
Page 20: Appendix 4: Diagnosis Diagram
Appendix 4: Diagnosis diagram Problem Wood will not stay lit Gives off insufficient heat Smoke emissions into the room when adding wood Fire in stove is too intense, is hard to adjust Deposit on the glass possible cause possible solution A cold flue usually fails to create sufficient draught. -
Page 21: Index
Index Cleaning appliance Coal ash content Adding fuel Combustible material Adding wood distance from smoking stove Connection Air control dimensions Air inlets Connection collar for connection to chimney Air leak Connection to chimney at top Air supply for fire Anthracite coal Connection to supply of outside air Ashes Control air supply... - Page 22 furniture Lubricant walls Lubricate Fireproof inner plates warning Maintenance Floors chimney bearing capacity clean glass fire safety cleaning the appliance Flue enamel maintenance fire-resistant inner plates requirements lubrication Flue gas sealing mass flow Mist, do not burn wood temperature Fog, do not burn wood Fuel Nominal output 13, 16...
- Page 23 Smoke emissions into the room Smoking stove Softwood Solving problems 13, 20 Stacking logs Storing wood Stove window cleaner Suitable fuel Supply of outside air 5, 8 Sweep chimney Temperature Unsuitable fuel Ventilation connect supply of outside air rule of thumb Ventilation louvre Vermiculite inner plates Walls...
Need help?
Do you have a question about the 225MF and is the answer not in the manual?
Questions and answers