Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Unique Manuals
  4. Refrigerator
  5. UGP 18F
  6. Owner's manual

Unique UGP 18F Owner's Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
510 L / 18 cu. ft.
UGP 18F ALL FRIDGE
Propane Refrigerator
OWNER'S GUIDE
serial number:
March 2016

Advertisement

loading

Related Manuals for Unique UGP 18F

Summary of Contents for Unique UGP 18F

  • Page 1 510 L / 18 cu. ft. UGP 18F ALL FRIDGE Propane Refrigerator OWNER’S GUIDE serial number: March 2016...
  • Page 2 UNIQUE UGP-18F Propane Refrigerator Installation and Owner’s Manual The installation of the appliance must conform with local codes or, in the absence of local codes, to the national Fuel Gas Code, ANSI Z233.1 and in Canada B149.2 Propane Storage and Handling Code...
  • Page 3 M A N U F A C T U R E D A N D C E R T I F I E D B Y Unique Gas Products Ltd “Personal Service & Knowledge makes us “Personal Service & Knowledge makes us Unique”...

  • Page 4: Table Of Contents

    T able of Contents Chapters Welcome Safety & Warnings ` Appliance Installation General Operating Instructions How To Use The Refrigerator Maintenance & Service Troubleshooting & Suggested Spares Carbon Monoxide Instructions (CM Model) Temperature Controls & Food Storage and Cleaning Parts & Warranty...

  • Page 5: Chapters

    U G P - 1 8 F Chapter Welcome & Congratulations ongratulations on your purchase of a UNIQUE refrigerator!. We are very proud of our product and we are completely committed to providing you with the best service possible. Your satisfaction is our #1 priority. Please read this manual very carefully. It contains valuable information on how to properly maintain your new gas refrigerator. We know you will enjoy your new refrigerator and Thank You for choosing one of our Unique Gas Products. We hope you will consider us for future purchases. PLEASE READ AND SAVE THESE INSTRUCTIONS This manual provides specific operation instructions for your model. Use your refrigerator only as instructed in this manual. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating and maintaining the appliance Please record your model and serial # shown below for future reference. This information is found on your CSA rating/serial plate inside the refrigerator compartment.

  • Page 6: Safety & Warnings

    U G P - 1 8 F Please mail in the Warranty Registration Card included with your refrigerator or you can register online at www.uniqueoffgrid.com Safety and Warnings If you smell gas Open windows • Don’t touch electrical switches • Extinguish any open flame • Immediately call your gas supplier • For your Safety Due to the potential of carbon monoxide (CO) from many different sources • inside your dwelling, and to meet most building codes, the dwelling must have a separate wall-mounted CO alarming device. This is beyond any safety devices/construction inherent to the Unique appliance. Do not store or use gasoline or other flammable vapors and liquids in the • vicinity of this unit or any other appliance...
  • Page 7 U G P - 1 8 F Warning Improper installation, adjustment, alteration, service or maintenance can • cause injury or property damage. Refer to this manual. For assistance or additional information consult a qualified installer, service agency or the gas supplier. This product can produce Carbon Monoxide. Carbon Monoxide has no • odour and can kill you. The burner and flue system must be kept clean. See owner’s manual for cleaning instructions. Installation Instructions The installation of the appliance must conform with • local codes or, in the absence of local national Fuel Gas Code, ANSI Z233.1 and in Canada B149.2...
  • Page 8 U G P - 1 8 F Chapter Installation For best performance at high ambient temperatures, there must be free air circulation over the cooling unit at the rear of the refrigerator. Ensure that there is a free air space above the refrigerator and that the flue (chimney) on top of the cabinet is not covered in any way. Do not place the refrigerator in a space where air circulation is restricted. Follow “clearance” instructions. This free-standing refrigerator requires accessibility to the back for servicing the gas equipment, which can be obtained by using a certified Flexible Metal Connector to allow the refrigerator to be withdrawn without disrupting the gas supply. “Where a flexible metal connector is used, it must comply with local authorities and in Canada with the provisions of the current Standard CAN 1-6.10, Metal Connectors for Gas Appliances”. However, if the Local Authorities require a rigid gas supply connector, the refrigerator should be located with sufficient space at the back for servicing or, if located against a wall a removable panel of a minimum size of 16” x 20” should be provided in the wall to allow access to the rear of the refrigerator. If you purchased a CM (CO Monitor model) you must follow instructions in Section 6 - 5.0 onward. Heat Shield The heat shield must be installed before operating the appliance. This is a CSA requirement. Un-wrap the heat shield (located inside the box along with the appliance). Mount heat shield with the screws (supplied) to left side of the fridge. See diagram. Heat Shield...
  • Page 9 U G P - 1 8 F Clearances Minimum clearances to combustible materials are: Top – 10” Sides – 2” Rear – 1” with left hand side rear shield mounted as shown in Figures. 1,2 & 3. Note: DO NOT install the appliance directly on carpeting. Carpeting must be removed or protected by a metal or wood panel beneath the appliance, which extends at least the full width and depth of the appliance. Air Flow - to release heat trap Fig#1 - This is ideal as both top and sides are open • Fig#2 – During hot/humid weather this confined area will become very • warm. To reduce heat build-up, we recommend providing an area for two air vents to circulate the air. One placed 6” off the floor and the other at or above the appliance top. Cold air return vents with adjustable louvers, work very well. This will allow hot air to evacuate the area and assist in air flow across the fins (similar to air passing across a radiator) – See Fig #4 Fig#3 – If this is your opening you only need to stay the diagramed distance • from the wall and ceiling. There is no need for additional venting.
  • Page 10 U G P - 1 8 F Gas Connection Hook-up to the gas supply line: 3/8” SAE (UNF 5/8” - 18) male flare connection. A backup wrench must be used when tightening gas supply fitting. All completed connections should be checked for leaks with a non-corrosive leak detector and/or soap and water for a bubble check. – ARNING O NOT USE FLAME TO CHECK FOR GAS LEAKS The gas supply system must incorporate a pressure regulator to maintain a supply pressure of not more than 12” water column and no less than 11” water column. (Max setting) Make sure the refrigerator and any other high BTU appliances on your line are turned on when checking the gas pressure. The appliance and its individual shut- off valve must be disconnected from the gas supply piping system during any pressure testing of that system at pressures in excess of ½” psig. In case detailed instructions on the installation and connection of the gas supply are required, contact your dealer or distributor. Leveling Ensure the fridge is level by using a 2ft level. This is accomplished by adjusting the feet at the front, underneath the fridge.

  • Page 11: General Operating Instructions

    U G P - 1 8 F Chapter General Operating Instructions Importance of Leveling a Refrigerator The refrigerator must be adjusted to a horizontal position in both directions. In an absorption refrigeration system, ammonia is liquefied in the finned condenser coil at the top rear of the refrigerator. The liquid ammonia then flows into the evaporator (inside the freezer section) and is exposed to circulating flow of hydrogen gas, which causes the ammonia to evaporate, creating a cold condition in the freezer. When starting this refrigerator for the very first time, the cooling cycle may require up to eight hours of running time before the cooling unit is fully operational to begin slowly loading compartment. The tubing in the evaporator section is specifically sloped to provide a continuous movement of liquid ammonia, flowing downward by gravity through this section. If the refrigerator is operated when not level, liquid ammonia will accumulate in sections of the evaporator tubing. This will slow the circulation of hydrogen and ammonia gas, or in severe cases, completely block it, resulting in a loss of cooling. Warranty will not cover recharge/rebuild if caused by not running the fridge level. This refrigerator operates only on LP Gas (Propane) Note: After changing an LP tank, or after a long shut off period, the gas line is likely to be filled with air. You may have to repeat the lighting procedure several times to purge the air out of the gas lines.We suggest first turning off gas at the control panel, then the tank,this will reduce an air trap in the gas line.
  • Page 12 U G P - 1 8 F Gas Operation “Start Up” Procedure – see Figure # 5 on next page for control panel 1. Locate the control panel below at the bottom front of fridge 2. Turn the gas shut off valve C to the ON position – to the left 3. Turn thermostat button B fully clockwise (Max), start to spark igniter button A before depressing the gas control button E, there may be a period of time required for air to escape from the gas line and flow up to burner. Length of time will vary depending on distance of the fridge to propane tank. Continue pushing the igniter button while holding in the gas button until the needle in the flame indicator D moves into the green area (to the left). 4. When the needle starts to move into the green area, this means flame is now lit. Stop sparking and continue to hold gas button E down for an additional 10 seconds. Release gas button, fridge should now stay lit and the needle should remain in the green area. 5. Once all the above has been done and you are ready to re-start your fridge for use, leave the thermostat button at “4”. Setting the thermostat to "4" will allow the fridge to get to optimum cooling temperature. It may be necessary to adjust the temperature control on the thermostat knob to suit your needs. 6. The quantity of food in the refrigerator, the frequency with which the refrigerator doors are opened and the room temperature will all affect refrigerator temperatures. “Shut Down” Procedure 1. Turn knob C to Gas “Off” position – to the right. Note: If using CO-Monitor, the monitor must be hooked up and be reset with the battery installed for the flame to stay on – Refer to Chapter 6...
  • Page 13 U G P - 1 8 F CONTROLS – See Fig 5. for description of controls Figure #5 Thermostat A thermostat controls the refrigerator cooling temperature; it can be adjusted by turning knob B to different settings to maintain the desired refrigerator temperature. Knob E also incorporates a safety device, which automatically shuts off the supply of gas if the flame goes out. The piezo electric igniter discharges sparks onto the burner when the button is pushed. 1. “Defrost” Defrost Setting on the Gas Thermostat: In gas operation, the thermostat closes its main valve and the burner runs continuously at the bypass rate or pilot flame. (Counter clockwise turn) 2. “Max” Setting of the Thermostat: In gas operation, the thermostat allows the burner to remain on high flame continuously. (Clockwise turn) 3. The thermostat can be adjusted between “Max” and “Defrost” to obtain the desired fridge temperature. When the thermostat reaches the set temperature, it will cut the burner back to bypass operation. The setting of the thermostat is critical and recommend it be adjusted to maintain a dry frost on the cooling fins (approx. 38° Fahrenheit or 3° Celsius). Adjust the thermostat knob closer to “Max” (clockwise) when the outside temperature rises.

  • Page 14: How To Use The Refrigerator

    U G P - 1 8 F How to Use the Refrigerator FOOD STORAGE COMPARTMENT The food storage compartment is completely closed and unventilated, which is necessary to maintain the required low temperature for food storage. The coldest areas in the refrigerator are under the cooling fins and at the bottom of the refrigerator. The warmer areas are on the upper door shelves. This should be considered when placing different types of food in the refrigerator. DEFROSTING Frost will gradually accumulate inside the refrigerator on the evaporator plate. It must not be allowed to grow too thick as it acts as an insulator and adversely affects the refrigerator performance. Check the formation of frost every week and when it exceeds 3/8” thick or more, defrost the refrigerator. It will not hurt the fridge to have the ice buildup. If it gets too thick it will act as an insulator and hamper the cooling ability of the fridge. Defrosting can be done with the fridge running if so desired. Simply open both doors and turn thermostat to Defrost, or fully counter clockwise. Once the ice starts to melt a towel can be placed under the evaporator fins in the fridge, then pull off the ice. Wipe the fins clean and shut both doors. DO NOT USE A HOT AIR BLOWER PERMANENT DAMAGE , DO NOT COULD RESULT USE A KNIFE AN ICE PICK...

  • Page 15: Cleaning

    U G P - 1 8 F Cleaning Cleaning the refrigerator is usually done after it is defrosted or put into storage. To clean the interior liner of the refrigerator, use lukewarm dish soap solution. Use only warm water to clean the finned evaporator, gasket, ice trays and shelves. Never use strong chemicals or abrasives to clean these parts as the protective surfaces will be damaged. It is important to always keep the refrigerator clean. Dish soap is recommended. Interior Light The interior light is located inside the fridge compartment at the top. You can replace it by unscrewing counter clockwise. Four “D” size batteries operate the interior light. The battery compartment is located on the exterior back of the fridge, bottom right side while facing the back of the fridge.
  • Page 16 U G P - 1 8 F Chapter Maintiance & Service The user should be aware of service that must be done on a regular schedule to keep the refrigerator operating properly. Installation must be by a licensed gas fitter in accordance with local codes or in the absence of local national Fuel Gas Code, ANSI Z233.1 and in Canada B149.2 Propane Storage and Handling Code (latest edition). REFRIGERATOR REMOVAL Before working on the refrigerator, shut off the gas supply. Disconnect the gas supply line at the rear of the refrigerator. Always use a back up wrench when loosening and tightening this connection. Cap the gas supply line and remove the refrigerator. Replacement is the reverse of removal. Check all connections for gas leaks. Refer to Chapter 2 INSTALLATION PERIODIC MAINTENANCE Before working on refrigerator, shut off the gas supply. Disconnect the gas line at the rear of the refrigerator. Always use a back up wrench when loosening and tightening this connection. Cap the gas supply line and remove refrigerator.
  • Page 17 U G P - 1 8 F Check all connectors in the complete refrigerator LP gas system for gas • leaks. The LP gas supply must be turned on. Apply a non corrosive bubble solution to all LP connections. The appearance of bubbles indicates a leak and should be repaired immediately by a qualified serviceman. – ARNING O NOT USE FLAME TO CHECK FOR GAS LEAKS Check burner flame for proper appearance. The flame should be light blue with no yellow at the tip. See figure #6 Fig. #6 Fig. #7 The LP gas pressure should be checked and the main regulator readjusted • if pressure is incorrect. The correct operating pressure is 11” W.C. (water column). Inspect the flue baffle, it should be clean and free of soot. Any soot • formation indicates improper functioning of the burner. The flue and burner both require cleaning in the following manner: Remove cover from the burner housing. Disconnect the wire from the spark electrode Remove the burner Remove the wire and flue baffle from the top of flue tube. Clean the flue from the top using a flue brush, be sure to cover the...
  • Page 18 U G P - 1 8 F burner if remaining intact to eliminate dirt falling into burner. Replace the flue baffle. Clean burner tube with compressed air, check for fluff or spider webs. Before removing burner orifice, clean burner area of any soot, scale or dirt. Remove the orifice and soak it in alcohol (isopropyl alcohol or thinners) and blow it out with compressed air. Re-install and tighten burner orifice. Re-install burner Warning - DO NOT use a pin or wire when cleaning the burner orifice as damage can occur to the precision opening. This can cause damage to the refrigerator or create a fire hazard. It will also create extremely dangerous levels of carbon monoxide. Be sure to reconnect the wire to the electrode. Check the electrode for proper location and gap. See figure #8 Fig. #8 The inlet & outlet gas fittings on the refrigerator need to be checked for leaks. Apply a non corrosive bubble solution to the fittings and observe for leaks. The safety valve will not allow gas...
  • Page 19 U G P - 1 8 F o If leak occurs, then allow ten minutes to dissipate from the burner area. Fix leak then light the burner according to the instructions under G – ENERAL PERATIONG NSTRUCTIONS AS OPERATION HAPTER...
  • Page 20 U G P - 1 8 F Chapter TROUBLESHOOTING INSTRUCTIONS & SUGGESTED SPARE PARTS TO KEEP ON HAND REFRIGERATOR DOES NOT COOL, CHECK LIKELY CAUSES: 1. Burner orifice clogged. Clean. See section Maintenance & Service, C HAPTER Item #2. Periodic Maintenance, Items 1-9. 2. Check to ensure refrigerator is level – (left to right and front to back). 3. Restriction on air flow across cooling unit. 4. Heavy frost build up on evaporator fins. Defrost. 5. Flue baffle not inserted properly in flue tube. 6. Improperly set thermostat. See paragraph on thermostat. In hot weather or heavy use the setting should be closer to “Max” than usual. 7. Burner dirty. Clean. See Section M & AINTENANCE ERVICE HAPTER ERIODIC AINTENANCE 8.
  • Page 21 U G P - 1 8 F Spare Parts The following is a list of commonly used parts which are available: Burner orifice • Burner • Electrode • Thermocouple • Safety valve & thermostat • Piezo igniter (push button) • Baffle • Contact your dealer or an authorized service center for parts and repairs as needed. Quote Model & Serial # - See CSA rating/serial plate on inside left wall.
  • Page 22 U G P - 1 8 F Chapter Carbon Monoxide Monitor Instructions for Model UGP-18F OWNER’S MANUAL Model 9RV-SSO Carbon Monoxide Alarm for Appliance Safety Shutoff ATTENTION: PLEASE READ, FOLLOW AND SAVE! (See Additional Instruction Sheet for Safety Shutoff Connection) Dear New COSTAR 9RV-SSO Owner, Congratulations as you have taken steps to help ensure the health and safety of you and your family. We are proud to offer you our unique, patented CO Sensor technology that detects CO in a manner similar to the human body's response. Please read this owner's manual carefully so you will have a better understanding of the effects of CO poisoning and the COSTAR 9RV-SSO alarm device in conjunction with our UNIQUE propane refrigerator. To your good health and safety, Unique Gas Products WARNING: Failure to replace this product by the “REPLACE BY...
  • Page 23 U G P - 1 8 F DATE” printed on the alarm cover may result in death by Carbon Monoxide poisoning. Replace by date is six (6) years from date of manufacture WHAT YOU SHOULD KNOW ABOUT CO Carbon monoxide (CO) is an insidious poison. It is a colorless, odorless and tasteless gas. It is a cumulative poison. The following symptoms are related to CARBON MONOXIDE POISONING and should be discussed with ALL members of the household: MILD EXPOSURE...
  • Page 24 1. Immediately move to fresh air – outdoors or by an open door or window. Check that all persons are accounted for. Do not re-enter the premises or move away from the open door/window until the emergency services responders have arrived; the premises have been aired out, and your alarm remains in its normal condition; 2. Call your emergency services ( ___ - ________ ) [ fire department or 911 ]; If “service” signal sounds (RED LED flashes and horn beeps every 30 seconds); contact Unique Gas Products for troubleshooting and/or instructions to return the unit:...
  • Page 25 U G P - 1 8 F IMPORTANT CONSIDERATIONS: The COSTAR 9RV-SSO has been designed and is warranted to operate for six years. Never disconnect the battery to silence an alarm. The alarm will automatically sense when the level of CO in the air falls below the danger level. You should stay outside the residence, or unconditioned area and remain in fresh air until the alarm is silenced. When the alarm sounds, do not stand too close to the alarm. The sound produced by the alarm is loud because it is designed to awaken a person in an emergency. Prolonged exposure to the alarm at a close distance may be harmful to your hearing.
  • Page 26 U G P - 1 8 F assistance from outside your residence. – Know where to go to call the emergency service provider and or a qualified service technician. IMPORTANT: WHAT YOUR CO ALARM CAN AND CANNOT 4.1 This unit is designed to detect carbon monoxide (CO) and shutoff an appliance for safety only. 4.2 This CO alarm is designed for use within a single residential living unit. It is designed to detect carbon monoxide (CO) entering its sensing chamber. It does not sense combustible gas (such as natural gas, propane or (butane), heat, smoke or flames.
  • Page 27 U G P - 1 8 F WALL LOCATION: Mount the alarm at least 3 feet (usually 5 – 6 feet) from the floor. Figure 1: Recommended CO alarm wall mounting location is 5 to 6 feet from floor 5.3 LOCATIONS TO AVOID: Nuisance alarms are caused by placing units where they will not operate properly. To avoid nuisance alarms, do not place units: – Within 5 feet (1.5m) of any cooking appliance or furnace. – Near an open window or door, because the fresh air entering the opening may delay CO from reaching the alarm. – In damp or very humid areas or next to bathrooms with showers. Install detectors at least 10 feet (3 meters) away from bathrooms. – In very cold or very hot environments or in unheated buildings or outdoor rooms where the temperature can go below or above the operating range of the alarm. Temperature limits for proper operation are -20° F to 120° F ( -29° C to 49° C); Operating Humidity is 10 – 95% RH. – Good ventilation is recommended when household cleaning supplies or similar contaminants are used. CONDITIONS WHICH CAN RESULT IN TEMPORARY CO SITUATIONS: 5.4.1 Excessive spillage or reverse venting of fuel burning appliances (woodstoves, etc) caused by outdoor ambient conditions, such as: 1 Wind direction and/or velocity, including high gusts of wind. Heavy air in the vent pipes (cold/humid air with extended periods between cycles).
  • Page 28 U G P - 1 8 F 3 Simultaneous operation of several fuel burning appliances competing for limited internal air. 4 Vent pipe connections vibrating loose from clothes dryers, furnaces, refrigerators, or water heaters. 5 Obstructions in or unconventional vent pipe designs which can amplify the above situations. 5.4.2 Extended operation of un-vented fuel burning devices (range, oven, fireplace, etc.) 5.4.3 Temperature inversions, which can trap, exhaust gasses near the ground.
  • Page 29 U G P - 1 8 F Step A: Wall Alignment Step B: Alarm Activation Step C: Removal and Installation Figure 2: Installation Instructions To insure aesthetic alignment of the alarm with the hallway or wall, the UP arrow on the mounting plate must be vertical when wall mounting: (See Step A in Figure 2) As described in Figure 2, attach the mounting plate on the wall. Use the screws and anchors provided to secure the mounting plate. The battery is INSTALLED REVERSED FOR SHIPPING. Remove and reinstall the battery in the correct orientation as noted on the inside of the battery door. When installing the battery, align the “+” and “-“...
  • Page 30 U G P - 1 8 F Figure 3). Note the tamper resist pin will have to be removed in order to change the battery; this can be done easily with a long nose pliers. Using the long nose pliers pull the pin out of the hole, it is now possible to remove the alarm from the mounting plate. Figure 3: Tamper Resistant Locking Pin This box contains two self-adhesive labels. You should write the telephone numbers of the emergency service provider and a qualified technician in the space provided on the labels. Place one label next to the alarm, and the other label near a source of fresh air where you plan to gather after the alarm indicates the presence of carbon monoxide.
  • Page 31 U G P - 1 8 F 8.0 MAINTENANCE CLEANING YOUR ALARM: 8.1. Keep your CO alarms clean – use a damp (water only) cloth or vacuum. 8.2. To clean your alarm, remove it from the mounting bracket as outlined in Figure 2 Step D: Installation/Removal. IF TAMPER RESISTANT PIN HAS BEEN USED, REFER TO STEP 6.7 UNDER INSTALLATION INSTRUCTIONS FOR REMOVAL INSTRUCTIONS. (See Figure 3) 8.3 You can clean the interior of your alarm by using your vacuum cleaner hose and vacuuming through the openings around the perimeter of the alarm.
  • Page 32 U G P - 1 8 F They can be purchased anywhere batteries are sold, such as your local hardware store. 9.3 USE ONLY THE FOLLOWING 9 VOLT BATTERY FOR CO ALARM REPLACEMENT: Alkaline type: DURACELL: MN1604 WARNING USE ONLY THE BATTERY SPECIFIED. USE OF DIFFERENT BATTERIES MAY HAVE A DETRIMENTAL EFFECT ON THE CO ALARM. THE CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR HIGH HUMIDITY MAY REDUCE BATTERY LIFE. CHECK THE BATTERY MANUFACTURERS SPECIFICATIONS...
  • Page 33 U G P - 1 8 F Chapter Temperature Controls Note: Maximum setting is override; therefore the thermostat function is not operational at this setting. This setting is usually only required during very hot and humid days. COOL DOWN PERIOD To ensure safe food storage, allow the refrigerator to operate with the doors closed for at least 8 hours before loading it with food. REFRIGERATOR CONTROL NOTE: When first setting the controls or when changing a setting, wait 24 hours for the temperature to stabilize before making additional changes. TEMPERATURE ADJUSTMENT Adjust temperature gradually: move the knob in small increments, allowing • the temperature to stabilize. For colder interior temperatures, turn the knob clockwise. • For warmer interior temperatures, turn the knob towards counter-clockwise • Remember there is no fan to circulate the air in the refrigerator as in an electric fridge. For good circulation, do not block the internal cooling fins on back-wall and try to maintain a temperature of 38° F or 4°C in the fridge. NOTE: When first turning refrigerator on, move refrigerator controls to Max, which is the recommended initial setting. After 24 hours, adjust the controls as needed.
  • Page 34 U G P - 1 8 F Looking Inside SHELF ADJUSTMENT Refrigerator shelves are easily adjusted to suit individual needs. Before adjusting the shelves, remove all food. Simply slide shelf to the right to release from inserts and relocate to another position available on the wall of the cabinet. Note the top shelf is cut smaller due to the evaporator plate depth. Food Storage Ideas RESH OOD TORAGE The refrigerator should be kept between 38° F and 40° F (3.3° C and 4.4° • C) with an optimum temperature of 38° F (3.3°C). Avoid overcrowding the refrigerator shelves. This reduces the circulation • of air around the food and results in uneven cooling. Raw meat and poultry should be wrapped securely so leakage and • contamination of other foods or surfaces does not occur. Care and Cleaning Keep your refrigerator clean to prevent odor build-up. Wipe up any spills immediately and clean both sections at least twice a year. Never use metallic scouring pads, brushes, abrasive cleaners or strong alkaline solutions on any...
  • Page 35 U G P - 1 8 F NOTES: Do not use razor blades or other sharp instruments, which can scratch the appliance surface when removing adhesive labels. Any glue left from tape or labels can be removed with a mixture of warm water and mild detergent, or, touch the glue residue with the sticky side of tape you have already removed. Do not remove the certification/serial plate, lighting instructions or CO warning label.
  • Page 36 U G P - 1 8 F Chapter Parts Diagram and List...
  • Page 37 U G P - 1 8 F...
  • Page 38 U G P - 1 8 F Burner Train Assembly...
  • Page 39 U G P - 1 8 F UNIQUE UGP Fridge Item# ESCRIPTION UGP18F-01 – O ANEL UTER HITE UGP18F-02 UGP18F-03 UNIQUE NAME PLATE UGP18F-04 ANDLE OUNTING SCREW UGP18F-05 CREW UGP18F-06 ANDLE UGP18F-07 – B OTTOM UGP18F-08 UGP18F-09 – D CREW...
  • Page 40 U G P - 1 8 F Item# ESCRIPTION UGP18F-25 RIVET UGP18F-26 14.50 23.88 HELF MALL UGP18F-27 – L 16.69 23.88 HELF ARGE UGP18F-28 IGHT HIELD UGP18F-29 IGHT OCKET UGP18F-30 IGHT UGP1518-2 HERMOSTAT UGP1518-3 UTLET ITTING UGP18F-31 UTLET UGP18-51 URNER RACKET UGP18-52 URNER TUBE...
  • Page 41 U G P - 1 8 F Item# ESCRIPTION UGP-9RV-SS0 CO D 9RV SSO ETECTOR QMP-I NTERRUPTER CO-M NTERRUPTER LOCK FOR ONITORED FRIDGES QMP-18-FET CO-M OSFET ONITORED ODELS...
  • Page 42 5 YEAR LIMITED WARRANTY* Unique Gas Products Ltd. warrants that this UNIQUE refrigerator is free from defects in material and workmanship under normal usage and service under the following terms: This Warranty is made only to the first purchaser (”original purchaser”) who acquires this refrigerator for his/her own use and will be honored by Unique Gas Products Ltd. and by the Seller. Any part of this refrigerator returned to the Seller or Unique Gas Products Ltd., which upon examination is determined by them to have been defective in material or workmanship, will at their option be either repaired or replaced under this warranty, without charge for materials/parts. (customer is responsible for labour) The obligation to repair or replace defective parts will apply only to parts returned within one year of the date of purchase and will constitute the Sellers sole obligation under this Warranty. The cooling system (coil) is warranted for a total of five years...
  • Page 43 LIMITED WARRANTY COSTAR Model 9RV-SSO UNIQUE GAS PRODUCTS LTD offers you this limited warranty on your new carbon monoxide alarm, including all of its component parts except the battery. This limited warranty extends solely to the original end-user purchaser of this product, provided your purchase was made from an authorized vendor. Transfer or resale of this product will automatically terminate warranty coverage.