REMS Cento Instruction Manual
Hide thumbs
Also See for Cento:
- Instruction manual (165 pages) ,
- Instruction manual (8 pages) ,
- Instruction manual (133 pages)
Subscribe to Our Youtube Channel
Related Manuals for REMS Cento
Summary of Contents for REMS Cento
- Page 1 CUTTING INSTRUCTION MANUAL PART 1: REMS Cento REMS Cento RF REMS Cento 22V REMS Due Cento PART 2: REMS Nano REMS Nano 11v...
- Page 2 PART 1 PART 1: REMS Cento REMS Cento RF REMS Cento 22V REMS Due Cento...
- Page 3 Fig. 1 Fig. 2 Fig. 3 Cu-INOX (Art-Nr. 845050) Cu-INOX (Art-Nr. 845050) Cu-INOX V, s 10 (Art-Nr. 845051) St (Art-Nr. 845052) Cu (Art-Nr. 845053) RF (Art-Nr. 845054) C-SF (Art-Nr. 845055) P, s 21 (Art-Nr.
- Page 4 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Ø 40 – 70 Ø 70 – 110...
- Page 5 Fig. 10 360° Ø 12 mm 1 – 2 mm...
-
Page 6: General Power Tool Safety Warnings
Danger of injury. severe injury within a fraction of a second. ● Only move or carry the REMS Cento / REMS Cento RF / REMS Cento 22 V / REMS 4) Power tool use and care DueCento by the feed lever (6) when this has been locked as described in 2.2. -
Page 7: Technical Data
WARNING REMS Cento, REMS Cento RF, REMS Cento 22 V and REMS DueCento are intended for the purpose of cutting and deburring the inside and outside of pipes. All other uses are not for the intended purpose and are therefore prohibited. - Page 8 ≤ 10.0 mm ≤ 21.0 mm Operating temperature range REMS pipe cutting machines, REMS cordless pipe cutting machine -10 °C – +60 °C (14 °F – 140 °F) Battery -10 °C – +60 °C (14 °F – 140 °F) Rapid charger...
-
Page 9: Operation
Move the cutting wheel drive (1) forwards by turning the feed lever (6) until the Cento / REMS Cento RF, REMS Cento 22 V (Fig. 1 (6)). Pull out the spring plug pipe to be cut (5) can be placed on the rollers (3). Outside burr (sawing burr) (Fig. -
Page 10: Maintenance
For marking the insertion depth for fi ttings on pipes. For REMS Cento, REMS Cento 22 V. 5. Behaviour in the event of faults 5.1. Fault: Pipe cutting machine stops during operation. The LED of the machine status check (18) lights red (REMS Cento 22 V). Cause: Remedy: ●... -
Page 11: Manufacturer's Warranty
● Rollers (3) of the pipe cutting machine and/or the roller insert (14) ● Change rollers. damaged. 5.8. Fault: A wavy cutting edge is made when cutting stainless steel drainpipes/downpipes (EN 1124) with REMS Cento RF. Cause: Remedy: ● Feeding pressure too high. - Page 12 PART 2 REMS Curvo REMS Curvo 50 REMS Akku Curvo REMS Sinus...
- Page 13 Fig. 1 REMS Nano Fig. 2 REMS Nano 11 V Fig. 3...
- Page 14 573006 Ax-Press 40 14,4 V ● ● ● 560010 Cat 22 V VE 21,6 V ● ● ● 845007 Cento 22 V 21,6 V ● ● ● 347005 Collum 22 V 21,6 V ● ● 580004 Curvo 22 V 21,6 V ●...
- Page 15 (6) and the material rest(s). There is a risk of injury. clothing away from moving parts. Loose clothes, jewellery or long hair can be ● Use REMS Herkules 3B (accessory, Art. No. 120120), REMS Herkules Y caught in moving parts.
- Page 16 Use for the intended purpose 2.1. Electrical Connection WARNING WARNING REMS Nano and REMS Nano 11 V are intended for the purpose of cutting pipes. WARNING WARNING All other uses are not for the intended purpose and are prohibited. Caution: Mains voltage present! Before connecting the electric pipe cutting machine or the rapid charger, check whether the voltage given on the rating 1.1.
- Page 17 3.1. Work procedure The gear REMS Nano, REMS Nano 11 V runs in a life-long grease fi lling and Pull up the handle (7) until the pipe to be cut can be placed on the pipe rest therefore needs no lubrication.
- Page 18 Cause: Remedy: ● Mains lead defective (REMS Nano). ● Have the mains lead changed by qualifi ed personnel or an authorised REMS customer service workshop. ● Power tool defective. ● Have the power tool checked/repaired by an authorised REMS customer service workshop.
Need help?
Do you have a question about the Cento and is the answer not in the manual?
Questions and answers