Dodge HORNET 2024 Owner's Manual
Hide thumbs Also See for HORNET 2024:
Table of Contents

Advertisement

2 0 2 4 H O R N E T O W N E R ' S M A N U A L

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HORNET 2024 and is the answer not in the manual?

Questions and answers

James morris
April 23, 2025

What does a beeping noise indicate

1 comments:
Mr. Anderson
May 11, 2025

In a 2024 Dodge Hornet, a beeping noise can indicate several things:

1. Electronic Stability Control (ESC) – Buzzing or clicking sounds may occur when ESC is active. This is normal and stops when ESC becomes inactive.

2. Lane Keep Assist – A warning beep or flashing light may occur when the vehicle is approaching or crossing a lane marker.

3. ParkSense Park Assist – Increasing tone frequency indicates the vehicle is getting closer to an obstacle. A continuous tone means an obstacle is very close.

These sounds are warning alerts to assist the driver and indicate system activity or potential hazards.

This answer is automatically generated

Chuck
January 22, 2025

How do you open the gas tank door to fuel the vehicle

1 comments:
Mr. Anderson
February 10, 2025

To open the gas tank door on a 2024 Dodge Hornet:

1. Access the rear quarter trim panel in the cargo area on the right side of the vehicle.
2. Press the fuel door release button.
3. The fuel door will pop away from the vehicle.
4. Manually rotate the fuel door further to fully open it.

If the fuel door does not open due to ice buildup in cold conditions, lightly push on the door to break the ice and press the release button again.

This answer is automatically generated

Devin
March 18, 2025

How do I open the rear seatbelt compartment? My seatbelt is folded on itself and I cannot get it unstuck due to the limited space. Pulling the seatbelt further out makes it worse. Thanks

Subscribe to Our Youtube Channel

Summary of Contents for Dodge HORNET 2024

  • Page 1 2 0 2 4 H O R N E T O W N E R ’ S M A N U A L...
  • Page 2 ROADSIDE ASSISTANCE WARNING: Operating, servicing and maintaining a passenger vehicle 24 HOURS, 7 DAYS A WEEK AT YOUR SERVICE. CALL or off-highway motor vehicle can expose you to chemicals including engine 1-800-521-2779 VISIT CHRYSLER.RSAHELP.COM (USA) CALL 1-800-363-4869 OR VISIT FCA.ROADSIDEAID.COM (CANADA) exhaust, carbon monoxide, phthalates, and lead, which are known to the SERVICES: Flat...
  • Page 3: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION................7 GETTING TO KNOW YOUR VEHICLE .
  • Page 4 UCONNECT VOICE RECOGNITION QUICK TIPS — INTRODUCTION Remote Start Abort Message — If Equipped . . . 38 IF EQUIPPED ..... . . 51 Scheduled Cabin Conditioning (SCC) —...
  • Page 5 POWER SUNROOF — IF EQUIPPED ..71 WARNING LIGHTS AND MESSAGES ..87 Flash-To-Pass ....58 Opening And Closing The Sunroof .
  • Page 6 AUTOMATIC TRANSMISSION ... . . 103 INTELLIGENT ADAPTIVE CRUISE CONTROL — PARKVIEW REAR BACK UP CAMERA ..132 IF EQUIPPED ..... . 118 Ignition Park Interlock .
  • Page 7 MY CAR ......160 IN CASE OF EMERGENCY SERVICING AND MAINTENANCE PERFORMANCE PAGES ....161 HAZARD WARNING FLASHERS .
  • Page 8 DEPARTMENT OF TRANSPORTATION UNIFORM WARRANTY INFORMATION ....271 CNG And LP Fuel System Modifications ..266 TIRE QUALITY GRADES ....258 MOPAR®...
  • Page 9: Introduction

    FCA US LLC reserves the right to make changes to the model described for technical and/or commercial reasons. For further information, contact an authorized dealer. When it comes to service, remember that authorized dealers know your Dodge® best, have factory-trained technicians, genuine Mopar® parts, and care about your satisfaction.
  • Page 10: Symbols Key

    INTRODUCTION SYMBOLS KEY Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. WARNING! These statements apply to operating procedures that could result in a collision, bodily injury and/or death.
  • Page 11: Symbol Glossary

    INTRODUCTION SYMBOL GLOSSARY Red Warning Lights Some car components have colored labels with symbols indicating precautions to be Electric Power Steering (EPS) Fault Warning Light observed when using this component. It is important to follow all warnings when oper- page 88 ating your vehicle.
  • Page 12 INTRODUCTION Red Warning Lights Yellow Warning Lights Seat Belt Reminder Warning Light Acoustic Vehicle Alerting System (AVAS) Fault Warning Light page 89 page 90 Service Hybrid System Warning Light Active Speed Limiter Fault Indicator Light page 90 page 90 SOS Battery Fail Warning Light Auto Liftgate Fault Indicator Light page 90 page 90...
  • Page 13 INTRODUCTION Yellow Warning Lights Yellow Warning Lights Electronic Stability Control (ESC) OFF Warning Light Keyless Enter ‘n Go™/Service Passive Entry Warning Light page 91 page 92 Fuel Cutoff Warning Light Service Forward Collision Warning (FCW) Light page 91 page 92 Fuel Cutoff Failure Warning Light Service Stop/Start System Warning Light page 91...
  • Page 14 INTRODUCTION Yellow Indicator Lights Green Indicator Lights Exterior Lights Failure Indicator Light Parking/Headlights On Indicator Light page 93 page 94 Plug Status Indicator Light Forward Collision Warning (FCW) OFF Indicator Light page 94 page 94 Immobilizer Fail / VPS Electrical Alarm Indicator Light Turn Signal Indicator Lights page 94 page 94...
  • Page 15 INTRODUCTION White Indicator Lights Gray Indicator Lights Auto Low Beams Indicator Light PowerShot Unavailable Indicator Light page 95 page 95 PowerShot Available Indicator Light page 95 Sport Mode On Indicator Light page 95 Blue Indicator Lights High Beams Indicator Light page 95 Auto High Beams Active Indicator Light page 95...
  • Page 16: Getting To Know Your Vehicle

    GETTING TO KNOW YOUR VEHICLE Disposal of the High Voltage Battery HIGH VOLTAGE BATTERY WARNING! Your vehicle’s high voltage battery is designed to last • the life of your vehicle. See an authorized dealer for Your vehicle is equipped with a Lithium-ion high voltage Never try to remove the high voltage battery service information on the disposal of the battery if it should disconnect.
  • Page 17: Battery Conditioning

    GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! WARNING! • When the “Please Leave Key In RUN — Battery Con- • In the event of an accident that requires bodywork, In the event of a collision: ditioning Needed” message is displayed, keep the •...
  • Page 18: E-Selec Mode

    GETTING TO KNOW YOUR VEHICLE ○ The RBS uses conventional hydraulic friction brakes, E-SELEC MODE Vehicle will switch to hybrid mode upon reaching regenerative braking, or a combination to slow the < 1% State of Charge (SOC) or due to system This system allows the driver to select different modes vehicle.
  • Page 19: Ac Level 1 Charging (120 Volt, 12 Amp)

    GETTING TO KNOW YOUR VEHICLE WARNING! • Do not use the Portable Charging Cordset (EVSE) in building structures that use fuse-based circuit protection. Use only with electrical circuits pro- tected by circuit breakers. • Do not use the Portable Charging Cordset (EVSE) if other devices are plugged into the same circuit.
  • Page 20 GETTING TO KNOW YOUR VEHICLE Moving, Transporting, And Storage Instructions WARNING! WARNING! After use, the Portable Charging Cordset (EVSE) should • • There are no user serviceable parts inside the The Portable Charging Cordset (EVSE) has been be placed in the storage bag and put back in the cargo Portable Charging Cordset (EVSE).
  • Page 21 GETTING TO KNOW YOUR VEHICLE WARNING! INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR ELECTRIC SHOCK: Do not use the Portable Charging Cordset (EVSE) on electrical circuits with two-prong outlets; use with improper outlets could result in elec- tric shock, fire, property damage, and death or seri- ous injury.
  • Page 22 GETTING TO KNOW YOUR VEHICLE 2. Check to see if the Portable Charging Cordset is outside the time and day of the week, you may (EVSE) is ready to charge by reviewing the indicator override the schedule for this charging event by lights.
  • Page 23 GETTING TO KNOW YOUR VEHICLE NOTE: Any faults in charging are displayed by the LEDs, either steady or flashing, located on the status indicator dis- It is good practice to keep the ignition in the OFF posi- play of the Portable Charging Cordset (EVSE). Refer to tion while conducting Level 1 charging.
  • Page 24 GETTING TO KNOW YOUR VEHICLE Portable Charging Cordset (EVSE) Charging System Failure Troubleshooting Green LED Red LED Yellow LED Description Action/Consequences Carefully disconnect the Portable Charging Cordset (EVSE) from both the vehicle and power outlet and wait for the Overheating at the charging outlet of the domestic power plug and outlet to return to normal temperatures.
  • Page 25 GETTING TO KNOW YOUR VEHICLE Portable Charging Cordset (EVSE) Charging System Failure Troubleshooting Green LED Red LED Yellow LED Description Action/Consequences The system will make a new charge attempt after 30 sec- ON (Flashing) Electric charging current too high. onds (6 attempts total). The new charge attempt failed.
  • Page 26: Ac Level 2 Charging (240 Volt, 40 Amp)

    GETTING TO KNOW YOUR VEHICLE this charging event by plugging in the charge con- WARNING! nector, unplugging it, and then plugging it back into the vehicle charge inlet. Complete the double plug INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR sequence within 10 seconds for it to override the set ELECTRIC SHOCK: Do not use the Portable Charging schedule.
  • Page 27: Vehicle Charge Indicators

    GETTING TO KNOW YOUR VEHICLE • Charging times will vary based on the age, condi- The SOC indicator provides a visual indication of the tion, SOC, available current being provided to the high voltage battery’s charge status during charging. charger from its energy source, and temperature of It is also used to indicate a charging problem as well as the high voltage battery.
  • Page 28 GETTING TO KNOW YOUR VEHICLE Number Of Indicator Lights Illuminated Percent Of Battery Charge 1st light blinks 0 – 20% 1st light on, 2nd light blinks 21 – 40% 1st and 2nd lights on, 3rd light blinks 41 – 60% 1st, 2nd, and 3rd lights on, 4th light blinks 61 –...
  • Page 29: Hybrid Electric Pages

    GETTING TO KNOW YOUR VEHICLE White LED Charging Mode Icons Charge now Charge by scheduled charge (if set) Charging Button: has different uses and sequences Next to the charging inlet, there is an LED that changes LED Charging Inlet color based on charging status. depending on which charging mode is set: LED Light Color Status...
  • Page 30 GETTING TO KNOW YOUR VEHICLE Charging Schedule Pressing the app icon brings you to a set of hybrid electric pages: Power Flow, Driving History, Charging To set a charging schedule, select the Hybrid Electric Schedule, e-Save, and Charge Settings (if equipped). App on the touchscreen and follow these steps: 1.
  • Page 31 GETTING TO KNOW YOUR VEHICLE • • If other schedules (Charge Interval, etc.) are set at a The charging schedule can also be overridden if an EVSE is plugged in, unplugged, and then plugged in later time in addition to “Charge Until Full” being a second time to the vehicle.
  • Page 32: Keys

    GETTING TO KNOW YOUR VEHICLE Charge Settings — If Equipped This double plug sequence will override the set sched- KEYS ule in the Hybrid Electric App, and begin charging the The fifth screen within the Hybrid Electric App is the vehicle immediately.
  • Page 33 GETTING TO KNOW YOUR VEHICLE To Unlock/Lock The Doors And Liftgate Key Left Vehicle Feature Push and release the unlock button on the key fob once If a valid key fob is no longer detected inside the vehicle to unlock the driver’s door. If selected within Uconnect while the vehicle’s ignition system is in the ON/RUN or Settings, pushing the unlock button twice within five START position, the message “Key Fob Has Left The...
  • Page 34 GETTING TO KNOW YOUR VEHICLE NOTE: To replace the key fob battery, proceed as follows: • 1. Remove the emergency key (2) by sliding the emer- This feature is enabled through Uconnect Settings gency key release (1) on the back of the key fob and page 145.
  • Page 35: Sentry Key

    GETTING TO KNOW YOUR VEHICLE Programming And Requesting SENTRY KEY Additional Key Fobs The Sentry Key Immobilizer system prevents unauthor- Programming the key fob may be performed by an ized vehicle operation by disabling the engine. The sys- authorized dealer. tem does not need to be armed or activated.
  • Page 36: Ignition Switch

    GETTING TO KNOW YOUR VEHICLE NOTE: All of the key fobs provided with your new vehicle have The push button ignition can be placed in the following been programmed to the vehicle electronics modes: If the key fob battery is depleted, and the vehicle doors page 272.
  • Page 37: Keyless Enter 'N Go™ Ignition - Phev Only

    GETTING TO KNOW YOUR VEHICLE 2. Push the lock button on another key fob twice, or CAUTION! push the Passive Entry lock button on the door handle (with another key fob within range), waiting An unlocked vehicle is an invitation for thieves. three seconds between each push.
  • Page 38: Remote Start - If Equipped

    GETTING TO KNOW YOUR VEHICLE • • Mechanical power (Vehicle Propulsion) is not When Manual Mode/Tip Mode is in use CAUTION! available • When the engine is temporarily operating in Fuel ON/RUN and Oil Refresh Mode (e.g. if the system detects a An unlocked vehicle is an invitation for thieves.
  • Page 39: How To Use Remote Start

    GETTING TO KNOW YOUR VEHICLE For PHEV Models: The ignition can be placed in the • HOW TO USE REMOTE START Key Fob Panic button not pushed RUN (Propulsion System Available) position by pushing • System not disabled from previous Remote Start Push and release the Remote Start button on the key the ignition button with the key fob inside the vehicle, event...
  • Page 40: Remote Start Comfort Systems - If Equipped

    GETTING TO KNOW YOUR VEHICLE NOTE: REMOTE START COMFORT The instrument cluster display message stays active until the ignition is placed in the ON/RUN position. These features will stay on through the duration of SYSTEMS — IF EQUIPPED Remote Start, or until the ignition is placed in the SCHEDULED CABIN CONDITIONING When Remote Start is activated, the front and rear ON/RUN position.
  • Page 41: Vehicle Security System - If Equipped

    GETTING TO KNOW YOUR VEHICLE VEHICLE SECURITY SYSTEM — All of the following conditions must be met before the TO ARM THE SYSTEM vehicle will initiate a scheduled SCC event: Follow these steps to arm the Vehicle Security system: IF EQUIPPED •...
  • Page 42: To Disarm The System

    GETTING TO KNOW YOUR VEHICLE • If the alarm emits a sound even when the doors, you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, hood, and liftgate are closed, there is a fault with disarm the Vehicle Security system.
  • Page 43: Power Door Locks

    GETTING TO KNOW YOUR VEHICLE NOTE: POWER DOOR LOCKS • Manually locking the vehicle will not arm the Vehicle The power door lock switches are located on each front Security system. door panel. Push the switch to lock or unlock the doors and liftgate.
  • Page 44 GETTING TO KNOW YOUR VEHICLE NOTE: • A lock request is made by the Passive Entry door handle while a door is open. • Passive Entry may be programmed on/off through • A lock request is made by the door panel switch Uconnect Settings page 145.
  • Page 45: Automatic Door Locks - If Equipped

    GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: • • After pushing the door handle button, you must wait If the key fob is inadvertently forgotten inside of the cargo area, and an attempt is made to close it from two seconds before you can lock or unlock the outside, the liftgate will not lock.
  • Page 46: Dead Lock Device - If Equipped

    GETTING TO KNOW YOUR VEHICLE • 3. The gear selector was not in PARK, then is placed in CHILD-PROTECTION DOOR LOCK After engaging the Child-Protection Door Lock sys- PARK. tem, always test the door from the inside to make SYSTEM — REAR DOORS certain it is in the desired position.
  • Page 47: Heated Steering Wheel - If Equipped

    GETTING TO KNOW YOUR VEHICLE HEATED STEERING WHEEL — WARNING! IF EQUIPPED • Do not place anything on the steering wheel that The steering wheel contains a heating ele- insulates against heat, such as a blanket or steer- ing wheel covers of any type of material. This may ment that helps warm your hands in cold cause the steering wheel heater to overheat.
  • Page 48: Programming The Memory Feature

    GETTING TO KNOW YOUR VEHICLE The memory setting switch is located on the driver’s MEMORY POSITION RECALL MANUAL ADJUSTMENT FRONT door trim panel. The switch consists of three buttons: SEATS — IF EQUIPPED To recall the memory settings for driver one or two, •...
  • Page 49: Manual Adjustment Rear Seats

    GETTING TO KNOW YOUR VEHICLE TO LOWER THE REAR SEAT MANUAL ADJUSTMENT REAR WARNING! SEATS 1. Pull the seatback release lever located on either • Adjusting a seat while driving may be dangerous. side of the upper outer edge of the seat. Moving a seat while driving could result in loss of WARNING! control which could cause a collision and serious...
  • Page 50: Power Adjustment Front Seats - If Equipped

    GETTING TO KNOW YOUR VEHICLE Power Lumbar — If Equipped Forward Or Rearward Adjustment WARNING! The seat can be adjusted both forward and rearward. Vehicles equipped with power driver or passenger seats Push the seat switch forward or rearward, the seat will Be certain that the seatback is securely locked into may be equipped with power lumbar.
  • Page 51: Front Ventilated Seats - If Equipped

    GETTING TO KNOW YOUR VEHICLE FRONT VENTILATED SEATS — REAR SEAT ARMREST — WARNING! IF EQUIPPED IF EQUIPPED • Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cush- Located in the seat cushion and seat back The center part of the rear seat can also be used as a ion.
  • Page 52: Head Restraints

    GETTING TO KNOW YOUR VEHICLE Rear Head Restraint Adjustment HEAD RESTRAINTS The rear outboard head restraints can be adjusted up Head restraints are designed to reduce the risk of injury or down. by restricting head movement in the event of a rear To raise the outboard head restraint, pull upward on the impact.
  • Page 53: Uconnect Voice Recognition Quick Tips - If Equipped

    WARNING! Push the Voice Recognition (VR) button. You can also • say the Wake Up word “Hey, Dodge” or “Hey, Uconnect”. A loose head restraint thrown forward in a collision After the beep, say: or hard stop could cause serious injury or death to occupants of the vehicle.
  • Page 54: Additional Information

    GETTING TO KNOW YOUR VEHICLE ADDITIONAL INFORMATION CAUTION! © 2023 FCA US LLC. All rights reserved. Mopar and To avoid damage to the mirror during cleaning, never Uconnect are registered trademarks and Mopar Owner spray any cleaning solution directly onto the mirror. Connect is a trademark of FCA US LLC.
  • Page 55: Outside Mirrors

    GETTING TO KNOW YOUR VEHICLE Sun Visor Slide-On-Rod Feature — Power Folding — If Equipped POWER ADJUSTMENT MIRRORS If Equipped To fold the outside mirrors in, push the power folding The power mirror control switch is located on the driv- mirror switch.
  • Page 56: Heated Mirrors - If Equipped

    GETTING TO KNOW YOUR VEHICLE • UNIVERSAL GARAGE DOOR OPENER The HomeLink® indicator light is located above the center button. (HOMELINK®) — IF EQUIPPED NOTE: HomeLink® is disabled when the Vehicle Security sys- tem is active page 272. BEFORE YOU BEGIN PROGRAMMING HOMELINK®...
  • Page 57: Identifying Whether You Havea Rolling Code Or Non-Rolling Code Device

    GETTING TO KNOW YOUR VEHICLE Non-Rolling Code Garage Door Opener Final Steps IDENTIFYING WHETHER YOU HAVE 2. Place the garage door opener transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® A ROLLING CODE OR NON-ROLLING 1.
  • Page 58: Reprogramming A Single Homelink® Button

    GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: Canadian Radio Frequency (RF) laws require transmit- ter signals to time-out (or quit) after several seconds of ○ Canadian Radio Frequency (RF) laws require transmit- If the indicator light stays on constantly, program- transmission, which may not be long enough for ter signals to time-out (or quit) after several seconds of ming is complete and the garage door/device...
  • Page 59: Troubleshooting Tips

    GETTING TO KNOW YOUR VEHICLE EXTERIOR LIGHTS TROUBLESHOOTING TIPS If you are having trouble programming HomeLink®, here are some of the most common solutions: MULTIFUNCTION LEVER • Replace the battery in the garage door opener hand- held transmitter. • Push the LEARN button on the garage door opener to complete the training for a rolling code.
  • Page 60: Daytime Running Lights (Drls) - If Equipped

    GETTING TO KNOW YOUR VEHICLE NOTE: DAYTIME RUNNING LIGHTS (DRLS) To activate the Automatic High Beam Headlights, pro- ceed as follows: The engine must be running before the headlights will — IF EQUIPPED come on in the automatic mode. 1. Within the Uconnect system, set “Auto Dim High The Daytime Running Lights (DRLs) (low intensity) come Beams”...
  • Page 61: Cornering Lights - If Equipped

    GETTING TO KNOW YOUR VEHICLE CORNERING LIGHTS — BATTERY SAVER FEATURE IF EQUIPPED To protect the battery, if the headlight switch is left in the low beam or parking lights position when the igni- The cornering lights are a feature to improve visibility at tion is placed in the OFF position, the lights are deacti- night while turning the vehicle.
  • Page 62: Windshield Wipers And Washers

    GETTING TO KNOW YOUR VEHICLE Rear Overhead Light Timing While Getting Into The Vehicle The overhead lights turn on according to the following The rear overhead lights are activated or deactivated by modes: on/off switches located on the front overhead console •...
  • Page 63: Windshield Wiper Operation

    GETTING TO KNOW YOUR VEHICLE Rain Sensor Sensitivity Level WINDSHIELD WIPER OPERATION WARNING! Rotating the switch to the Low Sensitivity windshield during freezing weather, warm the Rain Sensing position, activates the first, windshield with the defroster before and during wind- less sensitive level of the Rain Sensing function.
  • Page 64: Rear Window Wiper/Washer

    GETTING TO KNOW YOUR VEHICLE The sensor has an adjustment range that varies pro- The rain sensor is able to recognize and automatically AUTOMATIC CLIMATE CONTROL gressively from wiper still (no stroke) when the wind- adjust itself when the following conditions occur: DESCRIPTIONS AND FUNCTIONS shield is dry, to wiper at continuous speed (fast opera- •...
  • Page 65 GETTING TO KNOW YOUR VEHICLE MAX A/C Button Recirculation Button NOTE: The blower speed increases to full only if warm out- Press and release the MAX A/C button on Press and release this button on the touch- let temperature can be guaranteed. Otherwise, the the touchscreen to change the current set- screen, or push the button on the faceplate, blower bars will be proportional to outlet air...
  • Page 66 GETTING TO KNOW YOUR VEHICLE Blower Control Bi-Level Mode CAUTION! Blower Control is used to regulate the Air comes from the instrument panel outlets • Do not use scrapers, sharp instruments, or abra- amount of air forced through the Climate and floor outlets.
  • Page 67: Automatic Temperature Control (Atc)

    GETTING TO KNOW YOUR VEHICLE Combine Modes 2. Next, adjust the temperature you would like the sys- Push the VR button on the steering wheel. After the tem to maintain by adjusting the temperature con- beep, say one of the following commands: Dual Level Combination trol buttons.
  • Page 68: Interior Storage And Equipment

    GETTING TO KNOW YOUR VEHICLE Window Fogging WEATHER CONTROL SETTINGS WARNING! Vehicle windows tend to fog on the inside in mild, rainy, Set the mode control to Cool & Humid Do not operate this vehicle with a glove compartment (Mix Mode) and turn (A/C) on to and/or humid weather.
  • Page 69: Usb Control

    GETTING TO KNOW YOUR VEHICLE Door Storage • • “(Phone Name) now connected. Previous connection The device can be controlled using the radio buttons was lost.” to play, and browse the contents of the device. Front Door Storage • • “Another device is in use through the same USB The audio device battery charges when plugged into Storage areas are located in the door trim panels.
  • Page 70: Power Outlets - If Equipped

    GETTING TO KNOW YOUR VEHICLE POWER OUTLETS — IF EQUIPPED WARNING! Your vehicle may be equipped with 12 Volt (13 Amp) If this outlet is misused, it may cause an electric power outlets that can be used to power cellular shock and failure.To avoid serious injury or death: phones, small electronics and other low powered elec- •...
  • Page 71: Wireless Charging Pad - If Equipped

    GETTING TO KNOW YOUR VEHICLE • WIRELESS CHARGING PAD — Place the device inside the prepared area delimited in To avoid interference with the key fob search, the wireless charging pad will stop charging when any the mat as shown in the image. Incorrect positioning IF EQUIPPED door or liftgate is opened, even if the engine is will prevent the phone from charging.
  • Page 72: Windows

    GETTING TO KNOW YOUR VEHICLE • Wireless chargers may implement certain methods WINDOWS WARNING! to prevent the phone from overheating during charg- ing such as slowing down the rate of charge. In cer- Never leave children unattended in a vehicle. Do not POWER WINDOW CONTROLS tain instances, the device may shut down for a brief leave the key fob in or near the vehicle or in a loca-...
  • Page 73: Power Window System Initialization

    GETTING TO KNOW YOUR VEHICLE NOTE: POWER WINDOW SYSTEM WIND BUFFETING INITIALIZATION • Operation of the sunroof is only possible with the Wind buffeting can be described as the perception of ignition in the ON/RUN position. pressure on the ears or a helicopter-type sound in the If power supply is interrupted, the electric window auto- ears.
  • Page 74: Opening And Closing The Sunroof

    GETTING TO KNOW YOUR VEHICLE Venting The Sunroof OPENING AND CLOSING THE Releasing the switch while the sunshade is in motion will stop the sunshade in a partially open position. Push and release the Vent button within one-half sec- SUNROOF ond and the sunroof will open to the vent position.
  • Page 75: Sunroof Maintenance

    GETTING TO KNOW YOUR VEHICLE NOTE: 3. Raise the hood completely. The operation is assisted by the addition of two gas props which hold If the switch is released prior to full completion of it in the open position. the operations described, the entire re-initialization procedure must be repeated from step 1.
  • Page 76: Liftgate

    GETTING TO KNOW YOUR VEHICLE To Unlock The Liftgate WARNING! Use the key fob or the interior door unlock button on the door panel to unlock the liftgate. Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.
  • Page 77: Power Liftgate - If Equipped

    GETTING TO KNOW YOUR VEHICLE When the liftgate button on the key fob is pushed two times, the turn signals will flash twice to signal that the liftgate is opening or closing, and an audible chime can be heard (if enabled in the Uconnect Settings page 145).
  • Page 78: Adjustable Power Liftgate Height

    GETTING TO KNOW YOUR VEHICLE • Power Liftgate Malfunction Procedure: If anything obstructs the power liftgate while it is WARNING! closing or opening, the liftgate will automatically 1. In the event of a power malfunction to the liftgate, reverse to the closed or open position. After multiple •...
  • Page 79: Cargo Area Features

    GETTING TO KNOW YOUR VEHICLE • To open or close the liftgate using hands-free activa- The Hands-Free Liftgate feature can be activated by WARNING! tion, use a straight in and out kicking motion under the any metallic object making a similar in-and-out •...
  • Page 80 GETTING TO KNOW YOUR VEHICLE 4. The rear shelf can be stored in the cargo area, or WARNING! behind the front seat backs. • Cargo tie-downs are not safe anchors for a child seat tether strap. In a sudden stop or accident, a tie-down could pull loose and allow the child seat to come loose.
  • Page 81: Getting To Know Your Instrument Panel

    GETTING TO KNOW YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER...
  • Page 82: Instrument Cluster Descriptions

    GETTING TO KNOW YOUR INSTRUMENT PANEL Use this QR code to access your digital 5. Oil Temperature Gauge INSTRUMENT CLUSTER DISPLAY experience. ○ The temperature gauge shows engine oil LOCATION AND CONTROLS temperature. Any reading within the normal range indicates that the engine is operating The instrument cluster display features a driver interac- satisfactorily.
  • Page 83 GETTING TO KNOW YOUR INSTRUMENT PANEL • The systems allow the driver to select information by Driver Interactive Display (Compass, Temp, Range to Empty, Trip A, Trip B, Average Fuel Economy, Current pushing the following buttons mounted on the steering Fuel Economy, Tire Pressure, and Time) wheel: •...
  • Page 84: Oil Change Reset

    GETTING TO KNOW YOUR INSTRUMENT PANEL • Five Second Unstored Messages To reduce the risk of a larger fire, the vehicle’s high OIL CHANGE RESET voltage propulsion system will turn off within thirty When the appropriate conditions occur, this type of Use this QR code to access your digital seconds of displaying this warning.At that time, the message takes control of the main display area for...
  • Page 85: Oil Change Indicator System

    GETTING TO KNOW YOUR INSTRUMENT PANEL • • OIL CHANGE INDICATOR SYSTEM Heavily depressed accelerator pedal position, Other electric propulsion system faults indicated by requesting high power demand - Beyond the limits a MIL - Please see an authorized dealer for service. Your vehicle is equipped with an engine oil change indi- of the electric drivetrain, will cause engine to run, •...
  • Page 86: Gear Shift Indicator (Gsi) - If Equipped

    GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: When operating in this mode, the gas engine will run to CAUTION! provide vehicle propulsion (electric only operation is The instrument cluster display menu items display in inhibited). A message will be displayed in the instru- the center of the instrument cluster.
  • Page 87 GETTING TO KNOW YOUR INSTRUMENT PANEL • PERFORMANCE Suggested lanes The instrument cluster display displays the current LKA • system settings. The information displayed depends on Address of the road to be followed after the change Performance page content automatically changes Lane Keep Assist system status and the conditions that of direction according to the selected drive mode.
  • Page 88: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped

    GETTING TO KNOW YOUR INSTRUMENT PANEL ○ The color of the gauge bar will change from green This is done by reducing power to or turning off non- to yellow to orange. essential electrical loads. • “Brake” is based on amount of deceleration (slow- Load reduction is only active when the engine is run- ing down).
  • Page 89: Warning Lights And Messages

    GETTING TO KNOW YOUR INSTRUMENT PANEL • Turning on all possible vehicle electrical loads (e.g. After a trip: cleared. If the light is either not on during startup, stays on, HVAC to max settings, exterior and interior lights, or turns on while driving, have the system inspected at an •...
  • Page 90 GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Throttle Control (ETC) Warning Door Open Warning Light If brake failure is indicated, immediate repair is necessary. Light This indicator will illuminate when a door is WARNING! ajar/open and not fully closed. This warning light will illuminate to indicate a problem with the ETC system.
  • Page 91 GETTING TO KNOW YOUR INSTRUMENT PANEL Liftgate Open Warning Light (N) and idle the vehicle. If the temperature reading You may receive one of the following messages if a fault does not return to normal, turn the engine off immedi- is detected: This warning light will illuminate when the ately and call for service...
  • Page 92: Yellow Warning Lights

    GETTING TO KNOW YOUR INSTRUMENT PANEL Service Hybrid System Warning Light — Transmission Fault Warning Light — Fuel Level Sensor Failure Warning Light If Equipped If Equipped This light illuminates when there is a fuel level sensor failure. If this light illuminates, This warning light will illuminate when ser- This light will illuminate (together with a mes- take it to an authorized dealer and have...
  • Page 93 GETTING TO KNOW YOUR INSTRUMENT PANEL Lane Keep Assist Warning Light — • If the ABS light does not turn on when the ignition is The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds placed in the ON/RUN position, have the brake system If Equipped will stop when ESC becomes inactive.
  • Page 94 GETTING TO KNOW YOUR INSTRUMENT PANEL Keyless Enter ‘n Go™/Service Passive Certain conditions, such as a loose or missing gas cap, CAUTION! Entry Warning Light poor quality fuel, etc., may illuminate the light after engine start. The vehicle should be serviced if the light Do not continue driving with one or more flat tires as The telltale will illuminate in the event of stays on through several typical driving styles.
  • Page 95: Yellow Indicator Lights

    GETTING TO KNOW YOUR INSTRUMENT PANEL Towing Hook Breakdown Warning Light Your vehicle has also been equipped with a TPMS mal- WARNING! function indicator to indicate when the system is not — If Equipped operating properly. The TPMS malfunction indicator is If you continue operating the vehicle when the Trans- combined with the low tire pressure telltale.
  • Page 96: Green Indicator Lights

    GETTING TO KNOW YOUR INSTRUMENT PANEL Forward Collision Warning (FCW) OFF Hold ‘n Go Indicator Light — If Equipped Turn Signal Indicator Lights Indicator Light — If Equipped Hold ’n Go keeps your vehicle at a complete When the left or right turn signal is activated, stop without you having to keep your foot on the turn signal indicator will flash indepen- This indicator light illuminates to indicate...
  • Page 97: Blue Indicator Lights

    GETTING TO KNOW YOUR INSTRUMENT PANEL Automatic Low Beam Indicator Light — Automatic High Beam Indicator Light — CAUTION! If Equipped If Equipped • Prolonged driving with the MIL on could cause This indicator appears when the automatic This indicator shows that the automatic high further damage to the emission control system.
  • Page 98: Emissions Inspection And Maintenance Programs

    GETTING TO KNOW YOUR INSTRUMENT PANEL If your OBD II system is not ready, you should see an Your vehicle has a simple ignition actuated test, which WARNING! you can use prior to going to the test station. To check if authorized dealer or repair facility.
  • Page 99: Starting And Operating

    STARTING AND OPERATING Keyless Enter ’n Go™ Functions — Using The ENGINE STARTING THE ENGINE — GAS NORMAL STARTING START/STOP Button Place the ignition switch in the START position and Before starting your vehicle, adjust your seat, adjust 1. The transmission must be in PARK or NEUTRAL. release when the engine starts.
  • Page 100: Extended Park Starting

    STARTING AND OPERATING EXTENDED PARK STARTING IF ENGINE FAILS TO START WARNING! If the engine fails to start after you have followed the NOTE: • If the vehicle has a discharged battery, booster “Normal Starting” procedure, and has not experienced cables may be used to obtain a start from a Extended Park condition occurs when the vehicle has an Extended Park condition as identified in “Extended...
  • Page 101: Starting The Vehicle - Phev

    STARTING AND OPERATING STARTING THE VEHICLE — PHEV In extreme temperatures, high or low, the high voltage 2. Push the ENGINE START/STOP button once, without the battery may need to be conditioned, and therefore may brake pedal being pressed, to place the ignition in the require the vehicle to be plugged in.
  • Page 102: Engine Break-In Recommendations

    STARTING AND OPERATING 2. The ignition button indicator will return to the OFF After providing the horn chirp alert, additional auto PARK BRAKE position. chirps will be inhibited until the gear selector has been moved out of PARK or ignition cycled. 3.
  • Page 103 STARTING AND OPERATING NOTE: Once the parking brake is fully engaged, the Brake WARNING! Warning Light in the instrument cluster and an indicator When parking on a hill, it is important to turn the front • on the switch will illuminate. If your foot is on the brake wheels toward the curb on a downhill grade and away Be sure the parking brake is fully disengaged pedal while you apply the parking brake, you may notice...
  • Page 104 STARTING AND OPERATING • There is no attempt to press the brake pedal and You should only make repairs for which you have the WARNING! accelerator pedal. knowledge and the right equipment. You should only • enter Brake Service Mode during brake service. The seat belt is unbuckled.
  • Page 105: Automatic Transmission

    STARTING AND OPERATING NOTE: CAUTION! WARNING! A dedicated message will appear in the instrument cluster display if Brake Service Mode cannot be reverse. You could lose control of the vehicle and Damage to the transmission may occur if the follow- deactivated.
  • Page 106: 6-Speed Or 9-Speed Automatic Transmission

    STARTING AND OPERATING PARK (P) 6-SPEED OR 9-SPEED AUTOMATIC The 9-speed transmission has been developed to meet the needs of current and future FWD/AWD vehicles. TRANSMISSION This range supplements the parking brake by locking Software and calibration are refined to optimize the the transmission.
  • Page 107 STARTING AND OPERATING AUTOSTICK – IF EQUIPPED The following indicators should be used to ensure that CAUTION! you have properly engaged the transmission into the AutoStick is a driver-interactive transmission feature PARK position: Towing the vehicle, coasting, or driving for any other providing manual shift control, giving you more control •...
  • Page 108 STARTING AND OPERATING In AutoStick mode, the transmission will shift up or To disengage AutoStick mode, return the gear selector may be illuminated. Limp Home Mode may allow the to the DRIVE (D) position, or press and hold the (+) vehicle to be driven to an authorized dealer for service down when the driver moves the gear selector rearward paddle shifter until "D"...
  • Page 109: All-Wheel Drive (Awd)

    STARTING AND OPERATING NOTE: If the “POWER STEERING SYSTEM HOT - PER- SPORT MODE — IF EQUIPPED FORMANCE MAY BE LIMITED” message and The torque converter clutch will not engage until the a steering wheel icon display on the instru- engine and/or transmission is warm (usually after 1 to Your vehicle is equipped with a SPORT Mode feature.
  • Page 110: Autostop Mode

    STARTING AND OPERATING AUTOSTOP MODE In the following situations the engine will not stop: TO START THE ENGINE WHILE IN • Driver’s seat belt is not buckled. AUTOSTOP MODE The Stop/Start feature is enabled after every normal • Driver’s door is not closed. customer engine start.
  • Page 111: To Manually Turn Off The Stop/Start System

    STARTING AND OPERATING NOTE: TO MANUALLY TURN OFF THE SYSTEM MALFUNCTION STOP/START SYSTEM • The Mode button also activates the Adaptive Cruise If there is a malfunction in the Stop/Start system, the Control (ACC) system. Pushing the Mode button will system will not shut down the engine.
  • Page 112: Exceeding The Set Speed

    STARTING AND OPERATING • If Adaptive Cruise Control (ACC) or the Active Speed The Active Speed Limiter can be deactivated by press- SIGN CAPTURE MODES ing the CANC button. In this case, the system is not Limiter is active when the ignition is placed in the The way in which the ISA system sets a new maximum completely turned off, and the driver can reactivate the OFF position, it will remain activated when the...
  • Page 113: Exceeding The Set Speed

    STARTING AND OPERATING EXCEEDING THE SET SPEED ADAPTIVE CRUISE CONTROL (ACC) WARNING! By fully pressing the accelerator pedal, the maximum Adaptive Cruise Control (ACC) increases the driving con- • The ACC system: set speed of the vehicle can be exceeded while the sys- venience provided by Cruise Control while traveling on ○...
  • Page 114 STARTING AND OPERATING Adaptive Cruise Control (ACC) Operation Adaptive Cruise Control Ready • When the driver’s door is open at low speeds When ACC is activated, but the vehicle speed setting • The buttons on the left side of the steering wheel oper- When the driver’s seat belt is unbuckled at low has not been selected, the white ACC icon will illumi- ate the ACC system.
  • Page 115 STARTING AND OPERATING • The Anti-Lock Brake System (ABS) activates WARNING! WARNING! • The gear selector is removed from the DRIVE position If the Active Speed Limiter is active, the system will The Resume function should only be used if traffic not react to vehicles ahead.
  • Page 116 STARTING AND OPERATING Using Cruise Control On Hills • If the switch is pushed upward or downward briefly to the second detent, the set speed will adjust in The transmission may downshift on hills to maintain the 10 km/h increments. The new set speed is reflected vehicle set speed.
  • Page 117 STARTING AND OPERATING Display Warnings And Maintenance • The distance setting is changed. • The system disengages page 112. LIMITED OPERATION WARNING The maximum braking applied by ACC is limited; how- ever, the driver can always apply the brakes manually, If a warning message appears in the instrument cluster if necessary.
  • Page 118: Traffic Sign Recognition - If Equipped

    STARTING AND OPERATING NARROW VEHICLES Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead. ACC Hill Example LANE CHANGING Stationary Object And Stationary Vehicle Example...
  • Page 119: Activation/Deactivation

    STARTING AND OPERATING Visual + Chime • If no speed limit signs are detected, the system will revert to the speed limit signs that are stored in the When Visual + Chime is selected, the system will alert Navigation system. the driver when the current speed of the vehicle •...
  • Page 120: Intelligent Adaptive Cruise Control

    STARTING AND OPERATING Speed Limit Exceeded INTELLIGENT ADAPTIVE CRUISE ACTIVE DRIVING ASSIST SYSTEM — When the vehicle’s speed exceeds the displayed speed CONTROL — IF EQUIPPED IF EQUIPPED limit, the speed limit sign on the instrument cluster dis- play will show a red outline to alert the driver. The Intelligent Adaptive Cruise Control (IACC) system OPERATION allows the driver to set the Adaptive Cruise Control...
  • Page 121: Turning Active Driving Assist On Or Off

    STARTING AND OPERATING Once the driver stops providing input to the steering TURNING ACTIVE DRIVING ASSIST When all system conditions are met as described in wheel, the system will require a few seconds to fully “System Engagement Conditions” in the next section, ON OR OFF resume lane centering assistance, especially during the system will engage and the steering wheel image in...
  • Page 122: Indications On The Display

    STARTING AND OPERATING • • • No fault warning lights for the vehicle radar or cam- If the vehicle is driving in constant traffic When the system is deactivated, the system status era are present indicator lights will turn off, the LaneSense system •...
  • Page 123: Minimum Risk Maneuver

    STARTING AND OPERATING Active Driving Assist Indicators Are Red SYSTEM STATUS WARNING! • Driver inattentiveness is still being detected, or Along with changes in the system’s indicator lights • Do not use a hand-held device when the Active driver take-over is being requested, warning the (green, yellow, and red), the system can also issue sev- Driving Assist system is engaged.
  • Page 124: Parksense Front/Rear Park Assist System

    STARTING AND OPERATING The Active Driving Assist system may have limited or ParkSense is active in DRIVE or REVERSE, as long as PARKSENSE DISPLAY reduced functionality when one of the following condi- the system is on. The system will remain active until the The warning display will turn on indicating the system tions occur: vehicle speed is increased to approximately 8 mph...
  • Page 125: Enabling And Disabling Parksense

    STARTING AND OPERATING Adjustable Chime Volume Settings If "Sensor Lock" appears in the instrument cluster dis- working properly. The ParkSense system might not play, make sure the outer surface and the underside of detect an obstacle behind or in front of the fascia/ Front and Rear chime volume settings can be selected the rear fascia/bumper and/or front fascia/bumper is bumper, or it could provide a false indication that an...
  • Page 126: Side Distance Warning (Sdw) System

    STARTING AND OPERATING Side Distance Warning Display WARNING! The Side Distance Warning screen will only be displayed • Before using ParkSense, it is strongly recommended if this feature is enabled within Uconnect Settings that the ball mount and hitch ball assembly be dis- page 145.
  • Page 127: Parksense Active Park Assist System - If Equipped

    STARTING AND OPERATING • ParkSense, when on, will reduce the volume of the driver maintains control of the accelerator, gear selec- WARNING! radio when it is sounding a tone. tor and brakes. Depending on the driver's parking maneuver selection, the ParkSense Active Park Assist result in injury or damage to vehicles or obstacles •...
  • Page 128: Enabling And Disabling The Parksense Active Park Assist System

    STARTING AND OPERATING ENABLING AND DISABLING THE The ParkSense Active Park Assist system will only oper- PARALLEL/PERPENDICULAR ate and search for a parking space when the following PARKSENSE ACTIVE PARK ASSIST PARKING SPACE ASSISTANCE conditions are present: SYSTEM OPERATION • Gear selector is in DRIVE.
  • Page 129 STARTING AND OPERATING • The driver is responsible to ensure that the selected parking space is suitable for the maneuver and free/clear of anything that may be overhanging or protruding into the parking space (e.g., ladders, tail- gates, etc. from surrounding objects/vehicles). •...
  • Page 130: Exiting The Parking Space

    STARTING AND OPERATING • Activation It is the driver’s responsibility to use the brake and WARNING! accelerator during the semi-automatic parking To activate this function, push the Active ParkSense maneuver. towing. Failure to do so can result in injury or dam- switch once, then select “Parallel Park Exit”...
  • Page 131: Lanesense - If Equipped

    STARTING AND OPERATING • • Construction equipment, large trucks, and other Take great care to ensure that conditions do not change during the parking maneuver (e.g. if there vibrations could affect the performance of are persons and/or animals in the parking place, ParkSense.
  • Page 132: Turning Lanesense On Or Off

    STARTING AND OPERATING When both lane markings are detected and the driver unin- TURNING LANESENSE ON OR OFF LANESENSE WARNING MESSAGE tentionally drifts out of the lane (no turn signal applied), the The LaneSense on/off button is located on the on the The LaneSense system will indicate the current lane LaneSense system provides a haptic warning in the form of end of the multifunction lever, to the left of the steering...
  • Page 133: Changing Lanesense Status

    STARTING AND OPERATING • • When the LaneSense system senses the lane has When the LaneSense system senses the lane has been approached and is in a lane departure situa- been approached and is in a lane departure situa- tion, the yellow left lane line begins to flash. At this tion, the left lane line changes from white to yellow, time, torque is applied to the steering wheel in the and the LaneSense telltale changes from green to...
  • Page 134: Parkview Rear Back Up Camera

    STARTING AND OPERATING • The system will not apply torque to the steering the camera image will continue to be displayed for up CAUTION! wheel whenever a safety system engages (Anti-Lock to 10 seconds unless the following conditions occur: Brakes, Traction Control System, Electronic Stability The vehicle speed exceeds 8 mph (13 km/h), the •...
  • Page 135 STARTING AND OPERATING Automatic Activation Of The Surround View Camera NOTE: Different colored zones indicate the distance to the rear of the vehicle. When the vehicle is shifted into REVERSE, the Rear • Front tires will be in image when the tires are View and Top View will automatically be displayed on The following table shows the approximate distances turned.
  • Page 136: Refueling The Vehicle - Gas

    STARTING AND OPERATING NOTE: WARNING! If the Rear View Camera view was selected through the Surround View Camera menu, exiting out of the Rear pedestrians, animals, other vehicles, obstructions, or View screen will return to the last known Surround View blind spots before backing up.
  • Page 137: Refueling The Vehicle - Phev (If Equipped)

    STARTING AND OPERATING REFUELING THE VEHICLE — PHEV 4. Fill the vehicle with fuel, and when the fuel nozzle “clicks” or shuts off, the fuel tank is full. (IF EQUIPPED) 5. Keep the nozzle in the filler for five seconds after nozzle clicks to allow fuel to drain from the nozzle.
  • Page 138 STARTING AND OPERATING ○ If pushing the fuel door release button a second time does not correct the problem, try using a different fuel pump. If premature fuel pump shut- off continues to be a problem, take the vehicle to an authorized dealer for service.
  • Page 139: Vehicle Loading

    STARTING AND OPERATING Gross Vehicle Weight Rating (GVWR) CAUTION! The GVWR is the total permissible weight of your vehicle To avoid fuel spillage and overfilling, do not “top off” including driver, passengers, vehicle, options and cargo. the fuel tank after filling. The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).
  • Page 140: Trailer Towing

    STARTING AND OPERATING Inflation Pressure Gross Trailer Weight (GTW) WARNING! This is the cold tire inflation pressure for your vehicle The GTW is the weight of the trailer plus the weight of Do not load your vehicle any heavier than the GVWR for all loading conditions up to full GAWR.
  • Page 141: Trailer Towing Weights (Maximum Trailer Weight Ratings)

    STARTING AND OPERATING Trailer Sway Control (TSC) Weight-Distributing Hitch WARNING! The TSC can be a mechanical telescoping link that can A Weight-Distributing system works by applying leverage • An improperly adjusted Weight-Distributing Hitch be installed between the hitch receiver and the trailer through spring (load) bars.
  • Page 142: Trailer And Tongue Weight

    STARTING AND OPERATING NOTE: NOTE: WARNING! The trailer tongue weight must be considered as part of Remember that everything put into or on the trailer the combined weight of occupants and cargo (i.e., the adds to the load on your vehicle. Also, additional Improper towing can lead to a collision.
  • Page 143 STARTING AND OPERATING NOTE: Towing Requirements — Tires WARNING! Do not cut or splice wiring into the vehicle’s wiring • Do not attempt to tow a trailer while using a com- harness. • Do not connect trailer brakes to your vehicle's pact spare tire.
  • Page 144: Towing Tips

    STARTING AND OPERATING TOWING TIPS Before towing, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic Transmission Select the DRIVE (D) range when towing. The transmis- sion controls include a drive strategy to avoid frequent shifting when towing.
  • Page 145: Recreational Towing

    STARTING AND OPERATING NOTE: Traction DRIVING TIPS • When towing your vehicle, always follow applicable When driving on wet or slushy roads, it is possible for a state and provincial laws. Contact state and provin- wedge of water to build up between the tire and road DRIVING ON SLIPPERY SURFACES cial Highway Safety offices for additional details.
  • Page 146: Driving Through Water

    STARTING AND OPERATING DRIVING THROUGH WATER WARNING! CAUTION! Driving through water more than a few inches/ • Driving through standing water may cause damage Do not drive on or across a road or path where water centimeters deep will require extra caution to ensure to your vehicle’s drivetrain components.
  • Page 147: Multimedia

    MULTIMEDIA UCONNECT SYSTEMS CUSTOMER PROGRAMMABLE WARNING! FEATURES • For detailed information about your Uconnect 5/5 NAV ONLY insert trusted media devices/components into your vehicle. Media of unknown origin could With 10.25-inch Display system, refer to your Uconnect possibly contain malicious software, and if Radio Instruction Manual.
  • Page 148 MULTIMEDIA NOTE: When making a selection, press the button on the ting is complete, press the Vehicle button to exit to the touchscreen to enter the desired menu. Once in the screen. Pressing the Up or Down Arrow button on the •...
  • Page 149 This setting will allow you to change the voice options for the radio to “Male” or “Female”. Wake Up Word This setting will allow you to set the system “Wake Up” word. The available options are “Off”, “Hey, Uconnect”, and “Hey, Dodge”. Voice Barge-in This setting will allow Voice Barge-in to be turned on or off.
  • Page 150 MULTIMEDIA Setting Name Description Radio Off With Door This setting will allow you to determine if the radio shuts off when any of the doors are opened. Audio Settings This setting will open the submenu, containing the audio settings page 156. App Drawer Favoriting Pop-ups This setting will allow you to favorite app drawer pop-ups with “On”...
  • Page 151 MULTIMEDIA Safety/Driving Assistance When the Safety/Driving Assistance button is pressed on the touchscreen, the system displays the options related to the vehicle’s safety settings. These options will differ depending on the features equipped on the vehicle. The settings may display in list form or within subfolders on the screen. To access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.
  • Page 152 MULTIMEDIA Setting Name Description Drowsy Driver Alert This setting will monitor the driver’s driving habits and warn you of any changes, indicating that the driver may be drowsy. The avail- able options are “On” and “Off”. Highway Assist Steering Wheel Vibration This setting will customize the Highway Assist Steering Wheel Vibration.
  • Page 153 This setting will allow you to change the system’s voice to either “Male” or “Female”. Wake Up Word This setting will allow you to set the system’s “Wake Up” word. The available options are “Off”, “Hey, Uconnect”, and “Hey, Dodge”. Voice Barge-In This setting allows you to respond to a Voice Response before the statement is completed by the system.
  • Page 154 MULTIMEDIA Navigation — If Equipped When the Navigation button is pressed on the touchscreen, the system displays options related to the vehicle’s built-in Navigation system. These settings can change which icons display on the map, how “time to arrival is calculated”, and route types. For more information on Navigation and settings, refer to your Uconnect Radio Instruction Manual.
  • Page 155 MULTIMEDIA Lights When the Lights button is pressed on the touchscreen, the system displays the options related to the vehicle’s exterior and interior lights. NOTE: • When the “Daytime Running Lights” feature is selected, the daytime running lights can be turned on or off. This feature is only allowed by law in the country of the vehicle purchase.
  • Page 156 MULTIMEDIA Brakes After pressing the Brakes button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Auto Park Brake This setting will turn the Auto Park Brake on or off. Brake Service This setting will allow you to retract the brakes for servicing.
  • Page 157 MULTIMEDIA Setting Name Description Power Trunk Roof Level This setting will let you customize the angle of the power liftgate. Selectable options are “Custom”, “Level 1”, “Level 2”, “Level 3”, and “Level 4”. Hands Free Power Liftgate This setting will use hands-free technology to automatically open or close the liftgate. Selectable options are “On” and “Off”. Seats &...
  • Page 158 MULTIMEDIA Audio When the Audio button is pressed on the touchscreen, the system displays options related to the vehicle’s sound system. These settings can change the audio location within the vehicle, adjust the bass or treble levels, and auto-play settings from an audio device or smartphone. NOTE: Depending on the vehicle’s options, feature settings may vary.
  • Page 159 MULTIMEDIA Notifications When the Notifications button is pressed on the touchscreen, the system displays the options related to Notifications for the system. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Notification Sounds This setting controls the Notification chime that plays when a new notification is sent. The options are “On” and “Off”. App Drawer Favoriting Pop-Ups This setting turns the App Favorited Pop-Up on or off.
  • Page 160 MULTIMEDIA Geolocation After pressing the Geolocation button on the touchscreen, the following setting will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Geolocation This setting will turn the Geolocation on or off. Software Updates When the Software Updates button is pressed on the touchscreen, the system will display the setting related to updating the Uconnect software.
  • Page 161 MULTIMEDIA Reset When the Reset button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings. These settings can clear personal data and reset selected settings from other menus. NOTE: •...
  • Page 162: Steering Wheel Audio Controls

    MULTIMEDIA Short Press STEERING WHEEL AUDIO CONTROLS — STEERING WHEEL ROTARY This will activate or deactivate the Mute function for CONTROL IF EQUIPPED playback of audio tracks, radio stations, App streaming • Rotate upwards in Radio Mode to select the previ- and incoming calls.
  • Page 163: Performance Pages

    MULTIMEDIA NOTE: PERFORMANCE PAGES The graphic displayed may change depending on the different versions and engines. The Performance Pages is an application that provides performance indicators that will help you gain familiar- CONSUMPTION HISTORY ity with the capabilities of your vehicle in real time. To access Performance options, select “Performance”...
  • Page 164: Accessory Gauges

    MULTIMEDIA ACCESSORY GAUGES RADIO OPERATION AND MOBILE PHONES The internal wireless radio operates within guidelines found in radio frequency safety standards and recom- Selecting “Accessory Gauges” will relay the following mendations, which reflect the consensus of the scien- Under certain conditions, the mobile phone being on in information: tific community.
  • Page 165: Safety

    SAFETY SAFETY FEATURES If the ABS Warning Light remains on or comes on while WARNING! driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required. transmitting equipment. This interference can ANTI-LOCK BRAKE SYSTEM (ABS) However, the conventional brake system will continue to cause possible loss of anti-lock braking capability.
  • Page 166 SAFETY Dynamic Steering Torque (DST) Electronic Roll Mitigation (ERM) then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements ERM anticipates the potential for wheel lift by monitor- DST is a feature of the Electronic Stability Control (ESC) the Anti-Lock Brake System (ABS).
  • Page 167 SAFETY • Oversteer — when the vehicle is turning more than WARNING! WARNING! appropriate for the steering wheel position. • • Understeer — when the vehicle is turning less than Vehicle modifications, or failure to properly main- • In the ESC “Full Off” mode, the engine torque appropriate for the steering wheel position.
  • Page 168 SAFETY Emergency Stop Signal (ESS) — • remains on after several ignition cycles, and the vehicle The gear selection must match vehicle uphill direc- has been driven several miles (km) at speeds greater tion (i.e., vehicle facing uphill is in forward gear; If Equipped than 30 mph (48 km/h), see an authorized dealer as vehicle backing uphill is in REVERSE gear).
  • Page 169: Auxiliary Driving Systems

    SAFETY Ready Alert Braking (RAB) NOTE: RAB may reduce the time required to reach full braking • The BSM system DOES NOT alert the driver about during emergency braking situations. It anticipates rapidly approaching vehicles that are outside the when an emergency braking situation may occur by detection zones.
  • Page 170 SAFETY As part of the Lane Keep Assist system, if the vehicle begins to drift into an adjacent lane that has an active LED indication, the LED will flash if steering torque is provided to guide the vehicle back to the center of the lane page 129.
  • Page 171 SAFETY RCP monitors the rear detection zones on both sides of WARNING! the vehicle, for objects that are moving toward the side of the vehicle with a minimum speed of approximately The Blind Spot Monitoring system is only an aid to 3 mph (5 km/h), to objects moving a maximum of help detect objects in the blind spot zones.
  • Page 172: Forward Collision Warning (Fcw) With Mitigation - If Equipped

    SAFETY system is operating in Rear Cross Path (RCP) mode, the side view mirrors will be illuminated. The warning indi- If a Forward Collision Warning with Mitigation event system will respond with both visual and audible alerts cators will remain illuminated until blockage clearing begins at a speed below 39 mph (62 km/h), the system may provide the maximum braking possible to mitigate when a detected object is present.
  • Page 173 SAFETY • The FCW system is intended for on-road use only. If Changing the FCW status to “Only Warning” prevents By changing the FCW status setting to "Near", the sys- tem provides possible collision warnings on objects the vehicle is taken off-road, the FCW system should the system from providing autonomous braking, or addi- closer to the vehicle.
  • Page 174: Tire Pressure Monitoring System (Tpms)

    SAFETY FCW Limited Warning Turning PEB On Or Off NOTE: If the instrument cluster display reads “FCW Limited Functionality” or “FCW Limited Functionality Clean Front The default status of PEB is “On.” This allows the sys- Windshield” momentarily, there may be a condition that tem to warn you of a possible frontal collision with the limits FCW functionality.
  • Page 175 SAFETY The tire pressure will vary with temperature by approxi- For example, your vehicle may have a recommended CAUTION! cold (parked for more than three hours) placard pres- mately 1 psi (7 kPa) for every 12°F (6.5°C). This sure of 33 psi (227 kPa). If the ambient temperature is •...
  • Page 176 SAFETY Premium System Service TPMS Warning When a system fault is detected, the Tire Pressure The Tire Pressure Monitoring System (TPMS) uses wire- Monitoring System Warning Light will flash on and off less technology with wheel rim mounted electronic sen- for 75 seconds and then remain on solid.
  • Page 177: Occupant Restraint Systems

    SAFETY TPMS Deactivation — If Equipped OCCUPANT RESTRAINT SYSTEMS 2. If you install the compact or non-matching full size spare tire in place of a road tire that has a pressure The TPMS can be deactivated if replacing all four wheel below the low-pressure warning limit, upon the next Some of the most important safety features in your and tire assemblies (road tires) with wheel and tire...
  • Page 178: Seat Belt Systems

    SAFETY BeltAlert Warning Sequence 4. Never allow children to slide the shoulder belt SEAT BELT SYSTEMS behind them or under their arm. The BeltAlert warning sequence is activated when the Buckle up even though you are an excellent driver, even vehicle is moving above a specified vehicle speed range 5.
  • Page 179 SAFETY NOTE: WARNING! WARNING! If BeltAlert has been deactivated and the driver or out- • • board front seat passenger (if equipped with outboard Do not allow people to ride in any area of your A twisted seat belt may not protect you properly. In front passenger seat BeltAlert) is unbuckled the Seat vehicle that is not equipped with seats and seat a collision, it could even cut into you.
  • Page 180 SAFETY 5. Position the shoulder belt across the shoulder and WARNING! chest with minimal, if any slack so that it is comfort- involved in a collision, or if you have questions able and not resting on your neck. The retractor will regarding seat belt or retractor conditions, take withdraw any slack in the shoulder belt.
  • Page 181 SAFETY WARNING! • Wearing your seat belt incorrectly could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of the seat belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too.
  • Page 182 SAFETY Seat Belts And Pregnant Women 4. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Detaching Mini-Buckle With Seat Belt Tongue Seat Belts And Pregnant Women Inserting Latch Plate Into Buckle WARNING! Seat belts must be worn by all occupants including •...
  • Page 183 SAFETY Energy Management Feature retract completely in this case and then carefully pull WARNING! out only the amount of webbing necessary to comfort- The front outboard seat belt system is equipped with an ably wrap around the occupant’s mid-section. Slide the •...
  • Page 184: Supplemental Restraint Systems (Srs)

    SAFETY Air Bag System Components How To Disengage The Automatic Locking Mode Bag Warning Light, either momentarily or continuously. A single chime will sound to alert you if the light comes Unbuckle the combination lap/shoulder belt and allow • Occupant Restraint Controller (ORC) on again after initial startup.
  • Page 185 SAFETY Redundant Air Bag Warning Light WARNING! If a fault with the Air Bag Warning Light is • Never install a rear-facing child restraint in the detected, which could affect the Supplemen- front seat of a vehicle. Only use a rear-facing child tal Restraint System (SRS), the Redundant restraint in the rear seat.
  • Page 186 SAFETY Seat belts are necessary for your protection in all colli- The OCM uses input from the Sensor to determine the WARNING! sions, and also are needed to help keep you in position, front passenger’s most probable classification. The away from an inflating air bag. OCM communicates this information to the ORC.
  • Page 187 SAFETY Do not decrease OR increase the front passenger’s The ORC uses the classification to determine whether Front Passenger Seat Front Passenger seated weight on the front passenger seat the Passenger Advanced Front Air Bag inflation rate Occupant Status Air Bag Output should be adjusted.
  • Page 188 SAFETY The OCS determines the front passenger’s most prob- WARNING! able classification. If an occupant in the front passen- • ger seat is seated improperly, the occupant may provide Always wear your seat belt and sit properly, with an output signal to the OCS that is different from the the seatback in an upright position, your back against the seatback, sitting upright, facing for- occupant’s properly seated weight input, for example:...
  • Page 189 SAFETY Knee Impact Bolsters If the seat, trim cover, or cushion needs service for any reason, take the vehicle to an authorized dealer. Only The Knee Impact Bolsters help protect the knees of the FCA US LLC approved seat accessories may be used. driver and front passenger, and position the front occu- The following requirements must be strictly followed: pants for improved interaction with the front air bags.
  • Page 190 SAFETY Supplemental Side Air Bag Inflatable Curtains (SABICs) The Side Air Bags will not deploy in all side collisions, WARNING! including some collisions at certain angles, or some are located above the side windows. The trim covering side collisions that do not impact the area of the pas- the SABICs is labeled “SRS AIRBAG”...
  • Page 191 SAFETY Air Bag System Components lar to friction rope burns or those you might get slid- WARNING! ing along a carpet or gymnasium floor. They are not NOTE: • caused by contact with chemicals. They are not per- Being too close to the Side Air Bags during deploy- ment could cause you to be severely injured or manent and normally heal quickly.
  • Page 192 SAFETY ○ Enhanced Accident Response System Electric Motor (if equipped) message will be displayed on the instrument cluster. ○ Electric power steering The vehicle is not drivable in this state. ○ In the event of an impact, if the communication net- Brake booster In order to reset the high voltage battery and engine, ○...
  • Page 193 SAFETY Customer Action Customer Will See Each step MUST BE held for at least two seconds NOTE: Right turn light is OFF. 4. Place turn signal in neutral state. Left turn light BLINKS. Right turn light BLINKS. 5. Turn left turn signal switch ON. Left turn light is ON SOLID.
  • Page 194: Child Restraints

    SAFETY These data can help provide a better understanding of WARNING! WARNING! the circumstances in which crashes and injuries occur. • Do not attempt to modify any part of your air bag In a collision, an unrestrained child can become a NOTE: system.
  • Page 195 SAFETY Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Children who are two years old or younger and who have not reached Either an Infant Carrier or a Convertible Child Restraint, facing rear- Infants and Toddlers the height or weight limits of their child restraint ward in a rear seat of the vehicle...
  • Page 196 SAFETY Children Too Large For Booster Seats If the answer to any of these questions was “no,” WARNING! then the child still needs to use a booster seat in this Children who are large enough to wear the shoulder • After a child restraint is installed in the vehicle, do vehicle.
  • Page 197 SAFETY Lower Anchors And Tethers For CHildren LATCH Positions For Installing Child Your vehicle is equipped with the child restraint anchor- Restraints In This Vehicle age system called LATCH, which stands for Lower (LATCH) Restraint System Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH- equipped child seats.
  • Page 198 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Never “share” a LATCH anchorage with two or more child restraints. If the Can two child restraints be attached using a common lower LATCH center position does not have dedicated LATCH lower anchorages, use the anchorage? seat belt to install a child seat in the center position next to a child seat using the LATCH anchorages in an outboard position.
  • Page 199 SAFETY To Install A LATCH-Compatible Child 5. Tighten all of the straps as you push the child WARNING! Restraint restraint rearward and downward into the seat. Remove slack in the straps according to the child • Improper installation of a child restraint to the If the selected seating position has a Switchable restraint manufacturer’s instructions.
  • Page 200 SAFETY Installing Child Restraints Using The Lap/Shoulder Belt Systems For The seat belts in the passenger seating positions are Installing Child Restraints In This Vehicle Vehicle Seat Belt equipped with a Switchable Automatic Locking Retrac- tor (ALR) that is designed to keep the lap portion of the Child restraint systems are designed to be secured in seat belt tight around the child restraint so that it is not vehicle seats by lap belts or the lap belt portion of a...
  • Page 201 SAFETY Installing A Child Restraint With A Installing Child Restraints Using The Top 4. Pull on the webbing to make the lap portion tight Switchable Automatic Locking Retractor Tether Anchorage: against the child seat. (ALR): 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt WARNING! Child restraint systems are designed to be secured in...
  • Page 202: Safety Tips

    SAFETY possible, route the tether strap under the head SAFETY TIPS CONNECTED VEHICLES restraint and between the two posts. If not possible, Privacy of any wireless and wired communications can- lower the head restraint and pass the tether strap not be assured. Third parties may unlawfully intercept TRANSPORTING PASSENGERS around the outboard side of the head restraint.
  • Page 203 SAFETY Air Bag Warning Light WARNING! WARNING! The Air Bag Warning Light will turn on for • ONLY use the passenger’s side floor mat on the An improperly attached, damaged, folded, or stacked four to eight seconds as a bulb check when passenger’s side floor area.
  • Page 204: Periodic Safety Checks You Should Make Outside The Vehicle

    SAFETY PERIODIC SAFETY CHECKS YOU EXHAUST GAS Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In SHOULD MAKE OUTSIDE THE addition, inspect the exhaust system each time the WARNING! VEHICLE vehicle is raised for lubrication or oil change. Replace as required.
  • Page 205: In Case Of Emergency

    Hazard Warning Flashers Button assume all risks related to the use of the features services will only be operable if your Dodge Con- and applications in this vehicle. Only use the features Push the button to turn on the Hazard Warning Flash- nected services is active and you are connected to and applications when it is safe to do so.
  • Page 206 SOS operator has been made. POWER FOR ANY REASON (INCLUDING DURING OR nected with the SOS operator until the SOS AFTER AN ACCIDENT), THE DODGE CONNECT FEA- 3. Once a connection between the vehicle and an SOS operator terminates the connection.
  • Page 207: Jacking And Tire Changing - If Equipped

    NOTE: if a malfunction in any part of the system is • Dodge Connect Customer Care - Total support for detected. If the Air Bag Warning Light is illumi- • Your vehicle may be transmitting data as authorized Radio, Phone and NAV issues.
  • Page 208: Preparations For Jacking

    IN CASE OF EMERGENCY 5. Block both the front and rear of the wheel diagonally WARNING! opposite of the jacking position. For example, if the • Being under a jacked-up vehicle is dangerous. The driver’s front wheel is being changed, block the pas- vehicle could slip off the jack and fall on you.
  • Page 209: Jacking Instructions

    IN CASE OF EMERGENCY WARNING! • Block the wheel diagonally opposite the wheel to be raised. • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack.
  • Page 210 IN CASE OF EMERGENCY 2. Before raising the vehicle, use the wheel bolt wrench to CAUTION! loosen, but not remove, the wheel bolts on the wheel with the flat tire. Turn the wheel bolts counterclockwise Do not attempt to raise the vehicle by jacking on loca- one turn while the wheel is still on the ground.
  • Page 211 IN CASE OF EMERGENCY until each wheel bolt has been tightened twice page 264. If in doubt about the correct tight- ness, have them checked with a torque wrench by an authorized dealer or at a service station. 10. Lower the jack until it is free. Remove the wheel blocks.
  • Page 212: Tire Inflator Kit - If Equipped

    IN CASE OF EMERGENCY • TIRE INFLATOR KIT — IF EQUIPPED Adhesive label with the writing "Max. 50 mph INFLATION PROCEDURE (80 km/h)”, to be attached in a position easily visible to the driver (e.g. on the dashboard) after Use this QR code to access your digital WARNING! repairing the tire.
  • Page 213 IN CASE OF EMERGENCY 3. Verify that the valve stem (on the wheel with the 8. Insert the plug into the vehicle’s center console WARNING! deflated tire) is in a position that is near to the power outlet, then start the engine. •...
  • Page 214: Checking And Restoring Tire Pressure

    IN CASE OF EMERGENCY 15. If a pressure value of at least 26 psi (1.8 bar) is CHECKING AND RESTORING TIRE detected, restore the correct pressure (with engine PRESSURE running and Electric Park Brake applied), and drive immediately with great care to an authorized The compressor can also be used to check and, if nec- dealer.
  • Page 215: Sealant Cartridge Replacement

    IN CASE OF EMERGENCY JUMP STARTING SEALANT CARTRIDGE REPLACEMENT If your vehicle has a discharged battery, it can be jump The sealant liquid is subject to expiration and must be started using a set of jumper cables and a battery in replaced periodically.
  • Page 216: Jump Starting Procedure

    IN CASE OF EMERGENCY 4. If using another vehicle to jump start the battery, CAUTION! WARNING! park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. Do not connect the jumper cable to the negative (-) Failure to follow these procedures could result in damage to the charging system of the booster vehicle post of the discharged battery.
  • Page 217: Refueling In Emergency

    IN CASE OF EMERGENCY 3. Ensure funnel is inserted fully to hold flapper doors CAUTION! open. Accessories plugged into the vehicle power outlets 4. Pour fuel into funnel opening. draw power from the vehicle’s battery, even when not in use (i.e., cellular devices, etc.). Eventually, if CAUTION! plugged in long enough without engine operation, the To avoid fuel spillage and overfilling, do not “top off”...
  • Page 218: Gear Selector Override

    IN CASE OF EMERGENCY • White smoke coming from engine or exhaust 4. Press and maintain firm pressure on the brake CAUTION! pedal. • Coolant bottle coolant has bubbles present Driving with a hot cooling system could damage your 5. Locate the gear selector override access (at the vehicle.
  • Page 219: Towing A Disabled Vehicle

    IN CASE OF EMERGENCY NOTE: NOTE: CAUTION! Shifts between DRIVE (D) and REVERSE (R) can only be Push the ESC OFF button (if necessary), to place the • achieved at wheel speeds of 5 mph (8 km/h) or less. When “rocking” a stuck vehicle by shifting between Electronic Stability Control (ESC) system in the “Off”...
  • Page 220: Without The Key Fob

    IN CASE OF EMERGENCY Proper towing or lifting equipment is required to prevent TOW EYE — IF EQUIPPED CAUTION! damage to your vehicle. Use only tow bars and other Your vehicle may be equipped with a tow eye that can equipment designed for this purpose, following equip- •...
  • Page 221: Enhanced Accident Response System

    IN CASE OF EMERGENCY Tow Eye Installation CAUTION! The rear tow eye receptacle is located behind an access • Damage to your vehicle may occur if these guide- door on the passenger’s side of the rear lines are not followed. fascia/bumper.
  • Page 222: Servicing And Maintenance

    SERVICING AND MAINTENANCE Once A Month Or Before A Long Trip: SCHEDULED SERVICING Have your vehicle serviced as soon as possible, within the next 500 miles (805 km). • Check engine oil level. An authorized dealer will reset the oil change indicator Your vehicle is equipped with an automatic oil change •...
  • Page 223 SERVICING AND MAINTENANCE Mileage Or Time Passed (Whichever Comes First) Or Years: Or Kilometers: Inspect the brake linings, replace if necessary. Inspect the front suspension, tie rod ends and boot seals, replace if necessary. Inspect the CV/Universal joints. Inspect the PTU fluid level. Inspect the rear differential fluid level.
  • Page 224: Engine Compartment

    SERVICING AND MAINTENANCE ENGINE COMPARTMENT 1.3L PHEV ENGINE 1 — Oil Fill Cap/Engine Oil Dipstick 5 — Battery/Power Electronics Coolant Reservoir Cap 2 — Brake Fluid Reservoir Cap 6 — Engine Air Cleaner Filter (Located Under Engine Cover) 3 — Battery 7 —...
  • Page 225: 2.0L Engine

    SERVICING AND MAINTENANCE 2.0L ENGINE 1 — Engine Oil Fill 6 — Intercooler Coolant Reservoir Cap 2 — Engine Air Cleaner Filter 7 — Engine Oil Dipstick 3 — Brake Fluid Reservoir Cap 8 — Engine Coolant Pressure Cap 4 — Battery 9 —...
  • Page 226: Checking Oil Level

    SERVICING AND MAINTENANCE CHECKING OIL LEVEL WARNING! To ensure proper engine lubrication, the engine oil must Commercially available windshield washer solvents be maintained at the correct level. Check the oil level at are flammable. They could ignite and burn you. Care regular intervals, such as every fuel stop.
  • Page 227: Pressure Washing

    SERVICING AND MAINTENANCE NOTE: CAUTION! CAUTION! Intentional tampering with emissions control systems • may void your warranty and could result in civil penal- It is essential when replacing the cables on the Do not use chemical flushes in your engine oil as the battery that the positive cable is attached to the ties being assessed against you.
  • Page 228: Engine Air Cleaner Filter

    SERVICING AND MAINTENANCE Engine Oil Filter Selection CAUTION! A full-flow type disposable oil filter should be used for replacement. The quality of replacement filters varies Do not overtighten the engine air cleaner filter cover considerably. Only high quality Mopar® certified filters lid screws or damage may result.
  • Page 229: Air Conditioner Maintenance

    SERVICING AND MAINTENANCE Refrigerant Recovery And Recycling 4. Lift and remove the engine air cleaner filter cover to WARNING! access the engine air cleaner filter. R-1234yf • Use only refrigerants and compressor lubricants 5. Remove the engine air cleaner filter from the hous- R-1234yf Air Conditioning Refrigerant is a Hydrofluo- approved by the manufacturer for your air condi- ing assembly.
  • Page 230: Wiper Blades

    SERVICING AND MAINTENANCE WIPER BLADES At every valid activation of the Service Position com- 4. Push the wiper blade up and remove it. mand, the wiper blades are activated for 250 ms. The Clean the rubber edges of the wiper blades and the Service Position command can be repeated several windshield and rear window periodically with a sponge times to bring the blades into the desired position, up...
  • Page 231: Exhaust System

    SERVICING AND MAINTENANCE 3. Install a new wiper arm, securely tighten the nut and CAUTION! put the cap back in place. • The catalytic converter requires the use of EXHAUST SYSTEM unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions The best protection against carbon monoxide entry into control device and may seriously reduce engine the vehicle body is a properly maintained engine...
  • Page 232: Cooling System

    SERVICING AND MAINTENANCE NOTE: To minimize the possibility of catalytic converter damage: appearance, the system should be drained, flushed and • refilled with fresh engine coolant. Check the front of the Do not interrupt the ignition when the transmission • Mixing of engine coolant (antifreeze) other than A/C condenser for any accumulation of bugs, leaves, is in gear and the vehicle is in motion.
  • Page 233 SERVICING AND MAINTENANCE • To prevent reducing this extended maintenance period, Mixing engine coolant types is not recommended coolant in open containers or allow it to remain in it is important to use the same engine coolant (OAT and can result in cooling system damage. If HOAT puddles on the ground.
  • Page 234: Brake System

    SERVICING AND MAINTENANCE • Brake Master Cylinder 1. Remove the cap with level dipstick from the engine Check the coolant freeze point in the radiator and in coolant bottle. the coolant expansion bottle. If engine coolant The fluid in the master cylinder should be checked needs to be added, the contents of the coolant 2.
  • Page 235: Automatic Transmission

    SERVICING AND MAINTENANCE Fluid Level Check Selection Of Lubricant WARNING! The fluid level is preset at the factory and does not It is important to use the proper transmission fluid to • Overfilling the brake fluid reservoir can result in require adjustment under normal operating conditions.
  • Page 236: Fuses

    SERVICING AND MAINTENANCE Power Distribution Center/Fuses And FUSES The fuses protect electrical systems against excessive current. Relays General Information When a device does not work, you must check the fuse The Front Power Distribution Center is located in the element inside the blade fuse for a break/melt. engine compartment.
  • Page 237 SERVICING AND MAINTENANCE Underhood Power Distribution Location The fuse box screw and cover must be removed to gain For fuse box access, proceed as follows: 3. Remove the fuse box cover by sliding it upward. access to the fuses. 1. Turn the locking screw counterclockwise. 4.
  • Page 238 SERVICING AND MAINTENANCE Underhood Power Distribution Location...
  • Page 239 SERVICING AND MAINTENANCE Fuse Box Cover And Locking Screw Removal 1 — Fuse Cover 2 — Locking Screw Cavity Cartridge Fuse Maxi Fuse Mini Fuse Description * If Equipped – 70 Amp Tan – BCM1 – 70 Amp Tan – BCM2 / RDU 20 Amp Blue –...
  • Page 240 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Maxi Fuse Mini Fuse Description * If Equipped – 40 Amp Orange – BSM Pump – – 10 Amp Red ECM / TCM / AGSM – – 10 Amp Red Engine Primary Loads – –...
  • Page 241 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Maxi Fuse Mini Fuse Description * If Equipped – 70 Amp Tan – BCM1 – 70 Amp Tan – BCM2 / RDU 20 Amp Blue – – BMC3 40 Amp Green – – BCM Valves –...
  • Page 242 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Maxi Fuse Mini Fuse Description * If Equipped 40 Amp Green – – HVAC Fan – – 7.5 Amp Brown Rad Fan Enable – – 5 Amp Tan AGSM – – 7.5 Amp Brown Heated Mirrors &...
  • Page 243 SERVICING AND MAINTENANCE Supplemental Fuse Box Location...
  • Page 244 SERVICING AND MAINTENANCE Supplemental Fuse Box Cavity Mini Fuse Description 5 Amp Tan Electric Air Heater (EAH) 7.5 Amp Brown Electric Air Compressor (EAC) 5 Amp Tan Integrated Dual Charge Module (IDCM) 5 Amp Tan Charge Port Indicator Module (CPIM) 15 Amp Blue Power Electronic Coolant Pump 2 (PECP2) 15 Amp Blue...
  • Page 245 SERVICING AND MAINTENANCE Cavity Maxi Fuse Mini Fuse Description – – Not Used – 30 Amp Starter Relay R1 – 30 Amp Fuel Pump – – Not Used – 30 Amp Brake Booster Vacuum Pump Relays Cavity Maxi Fuse Mini Fuse Description –...
  • Page 246 SERVICING AND MAINTENANCE Interior Fuses The interior fuse panel is located under the driver’s side lower instrument panel. Interior Fuse Box Location Cavity Mini Fuse Description *If Equipped 7.5 Amp Brown HVAC Relay Coil & Power Outlet / Seat Relay Coil 20 Amp Yellow Front Passenger Window Lifter 20 Amp Yellow...
  • Page 247 SERVICING AND MAINTENANCE Cavity Mini Fuse Description *If Equipped Electronic Climate Control, Occupant Classification, Rear View Camera, Climate 7.5 Amp Brown Control, Headlamp Leveling, Terrain Select, Heated Rear Window, Trailer Tow, Haptic Lane Mod HCP / Reverse Gear / ISNSR / A/C Compressor / HVAC / Defrosting / Right & Left 7.5 Amp Brown Headlamp Leveling / LDW / Alarm Mod / Psg Airbag / Trailer Tow Mod / AFLM / Air Quality Sensor / ASBM...
  • Page 248 SERVICING AND MAINTENANCE Fuse Holder No. 1 Cavity Mini Fuse Description * If Equipped 20 Amp Yellow Sunroof* – – 30 Amp Green Power Liftgate Module (PLGM) 5 Amp Tan Driver And Passenger Ventilated Seats (HMSM*) 25 Amp Clear Heating And Memory Drive Seat Module 1 10 Amp Red Heating And Memory Drive Seat Module 2 7.5 Amp Brown...
  • Page 249: Bulb Replacement

    SERVICING AND MAINTENANCE NOTE: Tire Markings BULB REPLACEMENT • P (Passenger) — Metric tire sizing is based on US Replacement Bulbs, Names, And Part design standards. P-Metric tires have the letter “P” Numbers molded into the sidewall preceding the size designa- tion.
  • Page 250 SERVICING AND MAINTENANCE TIRE SIZING CHART EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on US design standards, or "..blank.." = Passenger car tire based on European design standards, or LT = Light truck tire based on US design standards, or T or S = Temporary spare tire or 31 = Overall diameter in inches (in)
  • Page 251 SERVICING AND MAINTENANCE Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
  • Page 252 SERVICING AND MAINTENANCE NOTE: Tire And Loading Information Placard Tire Loading And Tire Pressure Under a maximum loaded vehicle condition, Gross Axle NOTE: Weight Ratings (GAWR) for the front and rear axles must not be exceeded page 137. The proper cold tire inflation pressure is listed on the driver’s To determine the maximum loading conditions of your side B-pillar or the rear edge of the driver's side door.
  • Page 253 SERVICING AND MAINTENANCE Metric Example For Load Limit (4) The resulting figure equals the available amount of cargo and luggage For example, if “XXX” amount equals 635 kg and there will be five 68 kg passengers in your vehicle, the load capacity.
  • Page 254 SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
  • Page 255: Tires - General Information

    SERVICING AND MAINTENANCE TIRES — GENERAL INFORMATION Both underinflation and overinflation affect the stability CAUTION! of the vehicle and can produce a feeling of sluggish Tire Pressure response or over responsiveness in the steering. After inspecting or adjusting the tire pressure, always reinstall the valve stem cap.
  • Page 256 SERVICING AND MAINTENANCE very important. Increased tire pressure and reduced Damaged Run Flat tires, or Run Flat tires that have WARNING! vehicle loading may be required for high-speed vehicle experienced a loss of pressure should be replaced operation. Refer to an authorized tire dealer or original immediately with another Run Flat tire of identical size Fast spinning tires can be dangerous.
  • Page 257: Tire Types

    SERVICING AND MAINTENANCE Life Of Tire Replacement Tires WARNING! The service life of a tire is dependent upon varying fac- The tires on your new vehicle provide a balance of many This can cause unpredictable handling and stress tors including, but not limited to: characteristics.
  • Page 258: Spare Tires - If Equipped

    SERVICING AND MAINTENANCE Summer Or Three Season Tires — Spare Tire Matching Original Equipped Snow tires generally have lower speed ratings than If Equipped what was originally equipped with your vehicle and Tire And Wheel — If Equipped should not be operated at sustained speeds over Summer tires provide traction in both wet and dry con- 75 mph (120 km/h).
  • Page 259: Snow Traction Devices

    SERVICING AND MAINTENANCE Trim Level Axle Tire/ Snow Trac- WARNING! WARNING! Wheel Size tion Device (Maximum Compact and collapsible spares are for temporary Limited use spares are for emergency use only. Instal- emergency use only. With these spares, do not drive Projection lation of this limited use spare tire affects vehicle more than 50 mph (80 km/h).
  • Page 260: Tire Rotation Recommendations

    SERVICING AND MAINTENANCE For the proper maintenance intervals page 220. DEPARTMENT OF TRANSPORTATION CAUTION! The reasons for any rapid or unusual wear should be • corrected prior to rotation being performed. UNIFORM TIRE QUALITY GRADES Install device as tightly as possible and then retighten after driving about ½...
  • Page 261: Traction Grades

    SERVICING AND MAINTENANCE use, however, and may depart signifi- TEMPERATURE GRADES WARNING! cantly from the norm due to variations The Temperature grades are A (the The temperature grade for this tire is in driving habits, service practices, and highest), B, and C, representing the established for a tire that is properly differences in road characteristics and tire's resistance to the generation of...
  • Page 262: Storing The Vehicle - Phev

    SERVICING AND MAINTENANCE NOTE: BODYWORK If the HV battery is not able to condition itself and it becomes cold enough (or hot enough), the vehicle When the vehicle has not been started or driven for at will not start until the HV battery’s cell temperatures least 30 days, an “Extended Park Starting Procedure”...
  • Page 263: Body And Underbody Maintenance

    SERVICING AND MAINTENANCE BODY AND UNDERBODY prevent damage to the wheels. Mopar® Wheel Treat- ment, Mopar® Chrome Cleaner or their equivalent is MAINTENANCE Cleaning Headlights recommended, or select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels. Your vehicle is equipped with plastic headlights and fog Wheel And Wheel Trim Care lights that are lighter and less susceptible to stone CAUTION!
  • Page 264: Interiors

    SERVICING AND MAINTENANCE Seat Belt Maintenance INTERIORS CAUTION! Do not bleach, dye or clean the belts with chemical sol- • Do not use abrasive or strong cleaning materials vents or abrasive cleaners. This will weaken the fabric. SEATS AND FABRIC PARTS such as steel wool or scouring powder that will If the belts need cleaning, use a mild soap solution or scratch metal and painted surfaces.
  • Page 265: Plastic And Coated Parts

    SERVICING AND MAINTENANCE PLASTIC AND COATED PARTS LEATHER SURFACES GLASS SURFACES Use Mopar® Total Clean to clean vinyl upholstery. Mopar® Total Clean is specifically recommended for All glass surfaces should be cleaned on a regular basis leather upholstery. with Mopar® Glass Cleaner, or any commercial household-type glass cleaner.
  • Page 266: Technical Specifications

    TECHNICAL SPECIFICATIONS VEHICLE IDENTIFICATION NUMBER (VIN) TORQUE SPECIFICATIONS If either of the two hydraulic systems lose normal capa- bility, the remaining system will still function with some loss of overall braking effectiveness. This will be evident Lug Nut/Bolt **Lug Nut/Bolt Lug Nut/Bolt The VIN is found on the left front corner of the wind- by increased pedal travel during application and greater...
  • Page 267: Fuel Requirements

    TECHNICAL SPECIFICATIONS 1.3L ENGINE GASOLINE/OXYGENATE BLENDS This engine is designed to meet all emission Some fuel suppliers blend unleaded gasoline with oxy- regulations, and provide satisfactory fuel genates such as ethanol. economy and performance, when using high- quality unleaded regular gasoline having an CAUTION! octane rating of 87, as specified by the (R+M)/2 Method.
  • Page 268: Cng And Lp Fuel System Modifications

    TECHNICAL SPECIFICATIONS MATERIALS ADDED TO FUEL CNG AND LP FUEL SYSTEM FUEL SYSTEM CAUTIONS Besides using unleaded gasoline with the proper MODIFICATIONS octane rating, gasolines that contain detergents, corro- CAUTION! Modifications that allow the engine to run on Com- sion and stability additives are recommended. Using pressed Natural Gas (CNG) or Liquid Propane (LP) may gasolines that have these additives will help improve Follow these guidelines to maintain your vehicle’s...
  • Page 269: Fluid Capacities

    TECHNICAL SPECIFICATIONS FLUID CAPACITIES Metric Fuel (Approximate) All Engines 13.5 gal 51 L Engine Oil With Filter 1.3L Engine 5 qt 4.74 L 2.0L Engine 5 qt 4.73 L Cooling System* 1.3L Engine 5.9 qt 5.6 L 1.3L Battery/Power Electronics Coolant 7.4 qt 7.0 L (Contact an authorized dealer for service)
  • Page 270: Chassis Fluids And Lubricants

    TECHNICAL SPECIFICATIONS Component Fluid, Lubricant, or Genuine Part Engine Oil - 2.0L Engine We recommend using Mopar® API SP/GF-6A Certified SAE 5W-30 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-13340. Equivalent full synthetic 5W-30 API SP engine oil can be used but must have the API Donut trademark page 225.
  • Page 271: Customer Assistance

    CUSTOMER ASSISTANCE What to Do SUGGESTIONS FOR OBTAINING SERVICE Warranty service must be done by an authorized dealer. We strongly recommend that you take the vehicle to an If your vehicle requires jump start assistance, out of authorized dealer. They know your vehicle the best, and FOR YOUR VEHICLE gas/fuel delivery, tire service, lockout service or towing are most concerned that you get prompt and high qual-...
  • Page 272: Fca Us Llc Customer Center

    CUSTOMER ASSISTANCE Attention Claims Department closest authorized Chrysler, Dodge, Jeep®, or Ram CUSTOMER ASSISTANCE FOR THE dealer. If you choose to go to another dealer, you will be FCA US LLC reserves the right to modify the terms or HEARING OR SPEECH IMPAIRED responsible for the cost of the extra distance.
  • Page 273: Warranty Information

    CUSTOMER ASSISTANCE Use this QR code to access your digital FCA US LLC is not responsible for any service contract If NHTSA receives similar complaints, it experience. you may have purchased from another manufacturer. If may open an investigation, and if it you require service after the FCA US LLC New Vehicle finds that a safety defect exists in a Limited Warranty expires, please refer to the contract...
  • Page 274: Publication Order Forms

    CUSTOMER ASSISTANCE government should contact Transport To access your Owner's Information online, visit General Information www.mopar.com/om (US) or www.owners.mopar.ca Canada, Motor Vehicle Defect (Canada). The following regulatory statement applies to all Radio Investigations and Recalls at Frequency (RF) devices equipped in this vehicle. 1-800-333-0510 or go to Radio Call Tech Authority toll free at:...
  • Page 275 CUSTOMER ASSISTANCE RF Exposure Requirements REMARQUE: Des changements ou des modifications La operación de este equipo está sujeta a las siguientes dos condiciones: n’ayant pas été expressément approuvés par la partie To comply with FCC RF exposure compliance require- responsable de la conformité pourraient révoquer ments, the device must be installed and operated to 1.
  • Page 276 CUSTOMER ASSISTANCE BLIND SPOT MONITORING SYSTEM: Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his FCC ID: WU877V12CRN own expense. Radiofrequency radiation exposure Infor- This device complies with Part 15 of the FCC Rules.
  • Page 277 INDEX Alarm Fluid Level Check ....233 Arm The System ....39 Fluid Type ....233, 268 Active Driving Assist System .
  • Page 278 INDEX Connector Driving Universal Consumer Interface (UCI) ..67 Through Flowing, Rising, Or Shallow Standing Camera, Rear ....132 Console .
  • Page 279 INDEX Oil Synthetic ....225 Clean Air ....265 Delay .
  • Page 280 INDEX Anti Lock Brake System ... . .90 Park ..... .94 Passing .
  • Page 281 INDEX Mirrors ..... . .52 Operator Manual Automatic Dimming ....52 Owner's Manual .
  • Page 282 INDEX Tilting ....46, 48 Storage ..... .66 Storage, Vehicle .
  • Page 283 INDEX Rotation ....258 Transmission ....104 Washing Vehicle.
  • Page 287 ® Not all features shown in this manual may apply to your vehicle. For additional information, visit mopar.com/om (USA), owners.mopar.ca (Canada) or your local Dodge brand dealer. ®...
  • Page 288 ©2023 FCA US LLC. All Rights Reserved. Tous droits réservés. Dodge is a registered trademark of FCA US LLC or FCA Canada Inc., used under license. Dodge est une marque First Edition déposée de FCA US LLC ou FCA Canada Inc.,utilisée sous le permis. App Store is a registered trademark of Apple Inc. Google Play Store is a registered trademark of Google.

Table of Contents

Save PDF