56 volt lithium-ion cordless hedge trimmer (240 pages)
Summary of Contents for EGO HT2410-FC
Page 1
56-VOLT LITHIUM-ION CORDLESS HEDGE TRIMMER Français p. 27 MODEL NUMBER HT2410/HT2410-FC Español p. 57 WARNING: To reduce the risk of injury, the user must read and understand the Operator’s Manual before using this product. Save these instructions for future reference.
Page 3
To reduce your exposure to these chemical: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
We recommend a Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Consult your local waste authority for information regarding available recycling and/ or disposal options. Ingress IPX4 Protection Protection from splashing water Degree Volt Voltage Millimeter Length or size Inch Length or size 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 6
Power tools create sparks which may ignite the dust or fumes. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 7
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 8
Use the power tool, accessories, tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 9
Carry the hedge trimmer by the handle with the cutter blade stopped. When transporting or storing the hedge trimmer always fit the cutting device cover. Proper handling of the hedge trimmer will reduce possible personal injury from the cutter blades. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 10
Any part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this manual. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 11
Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan this tool to someone else, also loan these instructions to them to prevent misuse of the product and possible injury. SAVE THESE INSTRUCTIONS! 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact EGO customer service center 1-855-EGO-5656. This manual contains important information on to the safe assembly, operation and maintainance of your product.
Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. If any parts are damaged or missing, please return the product to the place of purchase. PACKING LIST PART NAME QUANTITY Hedge Trimmer Blade Guard Operator's Manual 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Before using this product, familiarize yourself with all operating features and safety rules. Hanging hole Hand guard Blade Front handle Tip protector Lock-off button Rear handle Battery-release button Latch Front switch lever Electric contacts Rear switch lever Battery-mounting slot Battery-ejection Hanging hole Blade guard 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 15
Protects the outer end of the blade. Battery-Release Button Press to release the battery pack from the tool. Latch Locks the battery pack in place when installed on the tool. Battery-ejection Aids in removing the battery. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
To Install Battery Pack (Fig. 2) Align the ribs of the battery pack with the battery-mounting slots on the hedge trimmer. Slide the battery pack in until it snaps into position. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 17
Always keep both hands on the hedge trimmer handles. Never hold shrubs with one hand while operating the hedge trimmer with the other hand. Failure to heed this warning may result in serious injury. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 18
Disconnect the electrical service to the damaged line or cord before attempting to free the blade from the line or cord. Failure to heed this warning will result in serious personal injury or possible death. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 19
Always cut stems or twigs that are less than 1 in. thick. Use a non-powered hand saw or pruning saw to trim large stems. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 20
When trimming the sides of the hedge, begin at the bottom and cut upwards. Trim the side of a hedge so that it will be slight narrower at the top.This shape will expose more of the hedge to sunlight, resulting in a more uniform growth. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
4. Remove the hedge trimmer from the vise; restart it and stop it to expose the unsharpened edges of the blade teeth. 5. Remove the battery pack and repeat the sharpening procedure above. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 22
Do not place your hand or fingers between blades or in any position where they could get pinched or cut. NEVER touch blades or service the unit with battery pack installed. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Replace with a new blade. Contact EGO service center for blade replacement service. ◾ ◾ Loose blade bolts. Tighten the blade bolts. Use a hex wrench and turn the bolt clockwise to tighten. 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
The warranty period for routine maintenance parts, such as, but not limited to, blades, trimmer heads, chain bars, saw chains, belts, scraper bars, blower nozzles, and all other EGO accessories is 90 days for residential purpose, 30 days for industrial, professional or commercial purpose. These parts are covered for 90/30 days from manufacture defects in normal working conditions.
Page 25
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. For customer service contact us toll-free at: 1-855-EGO-5656 or EGOPOWERPLUS. COM. EGO Customer Service, 769 SEWARD AVE NW / Suite 102 Grand Rapids, MI 49504 56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC...
Page 27
TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V NUMÉRO DE MODÈLE HT2410/HT2410-FC AVERTISSEMENT : TAfin de réduire les risques de blessure, l’utilisateur doit lire et comprendre le guide d’utilisation avant d’utiliser ce produit. Conservez le présent guide afin de pouvoir le consulter ultérieurement.
Page 28
Garantie ..........54-56 TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 29
Pour réduire votre exposition à ces produits chimiques, travaillez dans une zone bien ventilée et en portant l’équipement de sécurité approuvé, comme un masque antipoussières conçu spécialement pour ne pas laisser passer les particules microscopiques. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Portez toujours un équipement de protection oculaire conforme à la norme ANSI Z87.1. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Indice de IPX4 Protection contre les éclaboussures d’eau protection Volt Tension Millimètre Longueur ou taille TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 32
Le terme « outil électrique » dans un avertissement désigne votre outil électrique (avec cordon) alimenté par le secteur ou votre outil électrique (sans fil) alimenté par un bloc- pile. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 33
S’il est impossible d’éviter d’utiliser un appareil électrique dans un endroit humide, utilisez une alimentation protégée par un disjoncteur différentiel. L’utilisation d’un disjoncteur différentiel réduit les risques de décharge électrique. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 34
Ne forcez pas l’outil électrique. Utilisez l’outil électrique approprié à la tâche que vous souhaitez accomplir. L’utilisation de l’outil électrique approprié permet d’obtenir de meilleurs résultats, de façon plus sécuritaire, selon le régime de fonctionnement prévu. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 35
à une autre. Un court-circuit entre les bornes du bloc-pile peut occasionner des brûlures et un incendie. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 36
Lorsque vous utilisez le taille-haie, tenez-le avec les deux mains. Le tenir seulement avec une main peut causer une perte de contrôle et occasionner des blessures graves. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 37
En outre, inspectez visuellement les lames pour vérifier qu’elles ne sont pas endommagées (par exemple tordues, craquelées ou usées). Remplacez les lames uniquement par des lames du fabricant d’origine de l’équipement. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 38
à d’autres personnes qui l’utiliseraient. Si vous prêtez l’outil à une personne, prêtez-lui également ces instructions afin de prévenir un usage inapproprié de l’outil et des blessures potentielles. CONSERVEZ CES INSTRUCTIONS! TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Si vous éprouvez un problème que vous n’arrivez pas à régler facilement, veuillez communiquer avec le centre de service à la clientèle d’EGO au 1 855 EGO 5656. Le présent guide contient des renseignements importants pour assembler, utiliser et entretenir en toute sécurité...
Ne jetez pas le matériel d’emballage avant d’avoir inspecté soigneusement l’outil et de l’avoir fait fonctionner de manière satisfaisante. S’il y a des pièces manquantes ou endommagées, veuillez retourner l’outil à l’endroit où vous l’avez acheté. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
LISTE DES PIÈCES CONTENUES DANS L’EMBALLAGE NOM DE PIÈCE QUANTITÉ Taille-haie Protège-lames Guide d’utilisation TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Bouton de blocage Poignée arrière Bouton d’éjection du bloc-pile Verrou Levier d’interrupteur avant Contacts électriques Levier d’interrupteur arrière Rainure de guidage du bloc-pile Dispositif d’éjection Œillet de fixation Protège-lames du bloc-pile TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 43
Permet de retirer le bloc-pile lorsque l’on appuie dessus. Verrou Verrouille la batterie en place lorsqu'il est installé sur l'outil. Dispositif d’éjection du bloc-pile Aide à enlever le bloc-pile. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Tailler les haies, les arbustes et les buissons dont le diamètre des branches est inférieur à 26 mm (1 po). INSTALLATION ET RETRAIT DU BLOC-PILE (figures 2 et 3) REMARQUE : Chargez le bloc-pile au maximum avant sa première utilisation. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 45
Ne retirez JAMAIS le bloc-pile lorsque vous êtes en hauteur. Lorsque vous appuyez sur le bouton d’éjection du bloc-pile, celui-ci se détache du verrou. Saisissez le bloc-pile et enlevez-le du taille-haie. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 46
Assurez-vous que les lames de découpe ne touchent pas le sol ni tout autre objet. Tenez l’outil avec les deux mains : une main sur la poignée arrière et l’autre sur la poignée avant. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 47
à couper lorsque les lames sont en mouvement. Veillez à ce que les lames soient complètement à l’arrêt et que le bloc-pile soit enlevé avant de retirer un TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 48
Décidez de la hauteur souhaitée de la haie. Ensuite, placez un fil le long de la haie à la hauteur souhaitée. Puis, couper la haie juste au-dessus du fil. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 49
Coupez les côtés de la haie de manière à ce que celle-ci soit légèrement plus étroite en haut. Cette forme expose davantage la haie au soleil et permet une repousse plus uniforme. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Dent de découpe nécessaire pour laisser passer la lime entre les dents de découpe et les dents Dent de protection de protection. 2. Enlevez le bloc-pile de votre taille-haie. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 51
Rangez le taille-haie à l’intérieur, dans un endroit sec auquel les enfants n’ont pas accès. Rangez-le à l’écart des agents corrosifs, comme des produits chimiques de jardinage ou des sels fondants. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Page 52
être pincés ou coupés. Ne touchez JAMAIS les lames et ne procédez JAMAIS à l’entretien de l’outil sans avoir enlevé le bloc-pile au préalable. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
Les boulons des lames sont Serrez les boulons des lames. Au moyen lâches. d’une clé hexagonale, serrez les boulons en les tournant dans le sens des aiguilles d’une montre. TAILLE-HAIE SANS FIL À BLOC-PILE AU LITHIUM-ION DE 56 V — HT2410/HT2410-FC...
EGO POWER+ et les équipements d’alimentation électrique portable pour un usage personnel et domestique. Garantie limitée de 3 ans sur les blocs-piles et chargeurs du système EGO POWER+ pour un usage personnel et domestique. Garantie limitée de 2 ans/1 an sur les équipements d’alimentation électrique d’extérieur, les équipements d’alimentation électrique portables, les blocs-piles et les...
Page 55
Pour faire une réclamation au titre de la garantie, veuillez communiquer avec le service à la clientèle d’EGO au 1 855 EGO-5656 (numéro sans frais). Lorsque vous faites une réclamation au titre de la garantie, vous devez présenter le reçu de vente original. Un centre de service autorisé...
Page 57
ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS MODELO NÚMERO HT2410/HT2410-FC ADVERTENCIA: para reducir el riesgo de lesiones, el usuario debe leer y comprender el Manual del usuario antes de usar este producto. Guarde estas instrucciones para consultarlas en el futuro.
Page 58
Garantía ..........84-86 ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 59
Medidas para reducir la exposición a estos químicos: trabaje en un área bien ventilada y con el equipo de seguridad aprobado, como máscaras antipolvo especialmente diseñadas para filtrar partículas microscópicas. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Le recomendamos usar una máscara de seguridad de visión amplia sobre anteojos o anteojos de seguridad estándar con protección lateral. Use siempre protección ocular con la marca de cumplimiento de la norma ANSI Z87.1. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Grado de IPX4 protección de Protección contra salpicaduras de agua admisión Voltio Voltaje Milímetro Longitud o tamaño pulg. Pulgada Longitud o tamaño ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 62
(inalámbrica). SEGURIDAD EN EL ÁREA DE TRABAJO Mantenga el área de trabajo limpia y bien iluminada. Las áreas desordenadas y oscuras pueden provocar accidentes. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 63
Si no puede evitar operar una herramienta eléctrica en condiciones de humedad, use un suministro protegido por un dispositivo de corriente residual (GFCI, por sus siglas en inglés). El uso de un GFCI reduce el riesgo de descarga eléctrica. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 64
No fuerce la herramienta eléctrica. Use la herramienta eléctrica correcta para su aplicación. La herramienta eléctrica correcta hará mejor el trabajo y de manera más segura al ritmo para el que se diseñó. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 65
La conexión de los terminales entre sí de la batería puede producir quemaduras o incendios. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 66
Use ambas manos al operar la cortadora de orillas. Usar una sola mano podría provocar pérdida de control y producir lesiones personales graves. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 67
(por ejemplo, dobladuras, grietas y desgaste). Reemplace la cuchilla solo con una cuchilla del fabricante original del equipo (OEM, por sus siglas en inglés). ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 68
Si le presta esta herramienta a alguien, préstele también estas instrucciones para evitar el mal uso del producto y posibles lesiones. GUARDE ESTAS INSTRUCCIONES! ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
En caso de que tuviera algún problema que no pudiera resolver fácilmente, póngase en contacto con el Centro de Servicio al Cliente de EGO llamando al 1-855-EGO-5656. Este manual contiene información importante para el ensamble, el funcionamiento y el mantenimiento seguro de su producto.
Si hay alguna pieza dañada o faltante, devuelva el producto al lugar donde lo compró. LISTA DE EMPAQUE NOMBRE DE LA PIEZA CANTIDAD Cortadora de orillas Protector de la cuchilla Manual del usuario ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Botón de liberación de la batería Pasador Palanca de seguridad frontal Contactos eléctricos Palanca de seguridad posterior Ranura de montaje de la Eyección de la batería Orificio para colgar Protector de la cuchilla batería ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 72
Presione para liberar el paquete de batería de la herramienta. Pasador Bloquea la batería en su lugar cuando está instalada en la herramienta. Eyección de la batería Ayuda para retirar la batería. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Cortar orillas, matorrales y arbustos con ramas de menos de 26 mm (1 pulg) de diámetro. INSTALACIÓN Y EXTRACCIÓN DEL PAQUETE DE BATERÍAS (Fig. 2 y 3) NOTA: cargue completamente el paquete de baterías antes de usarlo por primera vez. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 74
La palanca de seguridad de la empuñadura frontal puede activarse en cualquiera de los tres lados, ofreciéndole varias opciones para un agarre cómodo cuando realice cortes. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 75
Luego, apriete la palanca de seguridad posterior con los dedos para hacer arrancar la cortadora de orillas. Suelte el botón de desbloqueo y continúe apretando el interruptor para que la máquina siga en funcionamiento. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 76
Sostenga la unidad con ambas manos con las cuchillas de corte apuntando lejos de usted. Use siempre la cortadora de orillas de manera adecuada. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 77
Decida el alto que desea que tenga la orilla. Luego, coloque un trozo de cuerda a lo largo de la orilla en este alto. Corte la orilla justo por arriba de esta línea de guía. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 78
Esta forma expondrá más de la orilla a la luz del sol y permitirá un crecimiento más uniforme. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Diente de corte entre el diente de corte y el diente de protección. Diente de protección 2. Retire el paquete de baterías de la cortadora de orillas. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 80
Limpie bien la cortadora de orillas antes de almacenarla. Almacene la cortadora de orillas en interiores, en un lugar seco que no sea accesible para los niños. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 81
No coloque su mano ni los dedos entre las cuchillas o en alguna posición donde puedan quedar atrapados o cortarse. NUNCA toque las cuchillas ni realice mantenimiento a la unidad con la batería instalada. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
◾ ◾ La cuchilla está obstruida. Retire la batería de la herramienta, retire la obstrucción con cuidado y vuelva a insertar la batería y a arrancar la herramienta. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Page 83
Los pernos de la cuchilla Apriete los pernos de la cuchilla. Con una están sueltos. llave hexagonal, gire el perno en dirección de las manecillas del reloj para apretarlo. ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Garantía limitada de 5 años en equipos de energía para exteriores y energía portátil EGO POWER+ para uso doméstico personal. Garantía limitada de 3 años en paquetes de baterías y cargadores con el Sistema EGO POWER+ para uso doméstico personal.
Page 85
Para obtener el servicio de garantía, póngase en contacto con Servicio al Cliente de EGO de manera gratuita al 1-855-EGO-5656. Cuando pida un servicio cubierto por la garantía, debe presentar el recibo con la fecha original de venta. Un centro de servicio autorizado será...
Page 86
Para obtener el servicio al cliente, póngase en contacto con nosotros de manera gratuita al: 1-855-EGO-5656 o visite: EGOPOWERPLUS.COM EGO Customer Service, 769 SEWARD AVE NW / Suite 102 Grand Rapids, MI 49504 ORILLADORA INALÁMBRICA DE ION DE LITIO DE 56 VOLTIOS — HT2410/HT2410-FC...
Need help?
Do you have a question about the HT2410-FC and is the answer not in the manual?
Questions and answers