Related Manuals for IPC Eagle Barrel Vac
Summary of Contents for IPC Eagle Barrel Vac
- Page 1 Industrial Vacuums Barrel Vac Operations and Parts Manual Models: BV190 BV290 BV390...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. WARNING DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. - Page 3 Warning: Operating a machine without observing all labels, decals, etc., could result in injury or damage. Read all machine labels before attempting to operate the machine. Make sure all of the labels are attached or fastened to the machine. Get replacement labels and decals from the manufacturer’s distributor.
- Page 4 120 Volt Machine Instructions For Connection To The Power Supply And The Electrical Ground This machine must be connected to the electrical ground to protect the operator from electrical shock. The machine has an approved power cord with three conductors and a plug with three terminals.
-
Page 5: Important Instructions
IMPORTANT INSTRUCTIONS Before use the equipment must be correctly assembled with all of its components Check that the electrical outlet is correct for use with the plug on the machine Before connecting, check that the specified motor voltage corresponds to the main ... -
Page 6: Periodic Maintenance
Periodic Maintenance (Every six to twelve months) 1. Check filter for wear, replace dirt saturated filters that do not respond to normal cleaning. 2. Inspect gasket seals and replace those which have begun to leak. 3. Examine carbon motor brushes and commutator. Servicing The Filter The filter is accessed by lifting the head assembly off the tank. -
Page 7: Carbon Brush Replacement
Servicing The Vac Motor Carbon Brush Replacement 1. Disconnect power cord from power source. 2. To access the vac motor, remove the screws that attach the main cover to the head assembly and set the cover to one side. 3. Remove the motor cover by removing two screws. -
Page 8: Filter Assembly
GC 1/90 Vacuum Motor Assembly Part # Description Qty. PMQE00258 1,00 KIT ELETRIC 600 1MOT.AUTOEST. MECB01827 1,00 WIRING 50CM MOTOR POKE-IN UL FSVR00127 1,00 CLAMP MECB01694 1,00 CONNECTING WIRE AWG-400-G/V-FF-4,2 MECB01702 1,00 MECB01527 2,00 CONNECTING WIRES AWG-350-ROS-FF-SP9 MECB01705 1,00 CONN.WIRE M.AWG-200-G/V-5,2-5,2 KTRI03437 0001 1,00... - Page 9 GC 2/90 Vacuum Motor Assembly Part # Description Qty. PMQE00259 ELECTRIC KIT 600 2MOT. AUTOEST. 1,00 MECB01827 WIRING 50CM MOTOR POKE-IN UL 2,00 FSVR00127 CLAMP 3,00 KTRI03437 0001 SCREW PFU TMT PHL 5X20 BLACK 1,00 KTRI03765 0002 SCREW PAT TMT PHL 5X40 BLACK 2,00 0003 MPVR11825...
- Page 10 GC 3/90 Vacuum Motor Assembly Part # Description Qty. CONNEC.WIRES AWG-350-GRI-FF-FF MECB01620 1,00 CONNECTING WIRES AWG-350-ROS-FF-FF MECB01617 1,00 WIRING 50CM MOTOR POKE-IN UL MECB01827 3,00 CLAMP FSVR00127 3,00 KTRI03437 SCREW PFU TMT PHL 5X20 BLACK 0001 1,00 KTRI03765 SCREW PAT TMT PHL 5X40 BLACK 2,00 0002 HANDLE TOPPER 600 VERDE IPC AU...
- Page 11 Barrel Vac Ring S920751 (Complete) S87390 Latch S81301 Rivet S820297 Inlet, Complete S82586 Gasket, Inlet S80725 Screw 5 x 25 S81015 Nut M5 S820749 Gasket, Lid...
-
Page 12: Warranty Policy
IPC Eagle will furnish and charge for replacement parts, including transportation, to the original owner through an IPC Eagle authorized service center. If the part is returned within 30 days and is found defective, the owner will be credited for the cost of the replacement part including shipping and handling. - Page 13 12450 Oliver Ave S Suite #300 Burnsville, MN 55337 651.686.5399 800.486.2775 www.ipceagle.com...
Need help?
Do you have a question about the Barrel Vac and is the answer not in the manual?
Questions and answers