Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKOKI WR 36DC
Summary of Contents for HIKOKI WR 36DC
- Page 1 WR 36DC Handling instructions...
-
Page 5: General Power Tool Safety Warnings
c) Prevent unintentional starting. Ensure the GENERAL POWER TOOL SAFETY switch is in the off -position before connecting WARNINGS to power source and/or battery pack, picking up or carrying the tool. WARNING Carrying power tools with your fi nger on the switch Read all safety warnings, instructions, illustrations and or energising power tools that have the switch on specifi... -
Page 6: Additional Safety Warnings
14. Please use the designated attachments which are the specifi ed range may damage the battery and listed in the operations manual and HiKOKI’s catalog. increase the risk of fi re. Accidents or injuries could result from not doing so. -
Page 7: Caution On Lithium-Ion Battery
21. The use of the battery in a cold condition (below 0 degree 7. If the battery charging fails to complete even when a Centigrade) can sometimes result in the weakened specifi ed recharging time has elapsed, immediately stop tightening torque and reduced amount of work. This, further recharging. -
Page 8: Regarding Lithium-Ion Battery Transportation
REGARDING LITHIUM-ION BATTERY USB DEVICE CONNECTION TRANSPORTATION PRECAUTIONS When transporting a lithium-ion battery, please observe the When an unexpected problem occurs, the data in a USB following precautions. device connected to this product may be corrupted or lost. WARNING Always make sure to back up any data contained in the USB Notify the transporting company that a package contains a device prior to use with this product. -
Page 9: Standard Accessories
Lights ; BSL14xx series) cannot be used with this tool. The battery remaining power is over 75%. ○ Due to HiKOKI’s continuing program of research and Lights ; development, the specifi cations herein are subject to change without prior notice. - Page 10 3. Charging CHARGING When inserting a battery in the charger, the charge indicator lamp will blink in blue. Before using the power tool, charge the battery as follows. When the battery becomes fully recharged, the charge 1. Connect the charger’s power cord to the receptacle. indicator lamp will light up in green.
-
Page 11: Mounting And Operation
MOUNTING AND OPERATION Regarding electric discharge in case of new batteries, etc. As the internal chemical substance of new batteries and Action Figure Page batteries that have not been used for an extended period is not activated, the electric discharge might be low when Removing and inserting the battery using them the fi... -
Page 12: Maintenance And Inspection
A worn or deformed hex. or a square-holed socket will not give an adequate tightness to the fi tting between Important notice on the batteries for the HiKOKI the nut or anvil, consequently resulting in loss of cordless power tools tightening torque. - Page 13 The charger’s vents are blocked, causing its Avoid blocking the vents. internal components to overheat. The cooling fan is not running. Contact a HiKOKI Authorized Service Center for repairs. The USB power lamp The battery’s capacity has become low. Replace the battery with one that has has switched off...
- Page 14 WR36DC WR36DC (2XCP) (NN) /min 0 - 3000 ― /min 0 - 2800 UC18YSL3 /min 0 - 2000 ― /min 0 - 1050 BSL36A18 /min 0 - 2800 ― /min 0 - 4000 M10 - M20 ― M10 - M16 •...
- Page 15 336471 BSL36..18 UC18YSL3 (14.4V - 18V) 336475 329897...
- Page 16 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99251511 G Printed in China...
Need help?
Do you have a question about the WR 36DC and is the answer not in the manual?
Questions and answers