SAFETY INSTRUCTIONS Please follow the warnings and cautions said below strictly. This will prevent to damage of your machine or any harm to your body or any lose which caused by any improper use of the machine. Read the manual carefully before first use and keep it for future references. When use the machine, please comply to the instruction to operate.
Page 4
• When damaged, it might be lead to fire. • Please do not use damaged power cord or plug. • It might lead to fire or electrocution. • Do not install the machine in wet place or near to water. •...
It is advisable to drink 500ml lukewarm water before use in order to eliminate the toxic wastes. Drink 3000ml of water daily for a healthier lifestyle as it can revitalize your energy in your body. Water can benefit your body as follows: •...
PARTS LIST Name Foot skin Inner hexagon cylindrical screw Washer Footplate Ornament of straps Switch Socket Metal clip for fixing ornament of straps Hexagon nipples Strengthening rod components Base casing Rubber sleeve Bearing sleeve Deep groove ball bearing Eccentric block Inner hexagon cylindrical screw Inner hexagon cylindrical screw Spring washer...
Page 8
Oscillation motor Motor insulation pad Hexagon nipple Big washer Insulation washer of motor seat Motor seat Insulation pad of motor seat Washer Spring washer Inner hexagon cylindrical screw Hexagon nipple Spring washer Flat washer Locating sleeve Axle of connecting rod Bracket of connecting rod Clamp spring of axle Connecting rod...
Page 9
Inner hexagon cylindrical screw Adjustable feet Washer Spring washer Inner hexagon cylindrical screw Washer Spring washer Inner hexagon cylindrical screw Upper handrail protection foam Upper handrail Main control panel sticker Phill disk head self-tapping Screw BMI sensor chip Main control Panel Display PCB Phill disk head self-tapping screw Column...
Plug Column LED PCB ASSEMBLY STEP 1: Take out the support tube (1) and main base (2) from packing carton. Connect the upper and lower signal cable. STEP 2: Put the support tube (1) into the base (2). Lock them with screws (4) and install the feet cushion.
STEP 4: Install the upper handrail (5) on the support tube with screw (8). This is final assembled picture. OPERATION INSTRUCTIONS UPPER CONSOLE MIDDLE CONSOLE...
Page 12
UPPER CONSOLE OPERATION Press this button to switch the time or speed display during the machine. 2. MODE window Display the current mode of machine, manual or automatic. 3. TIME / H-SPEED Display the time countdown or oscillation speed. Switch the display window mutually.
Page 13
MIDDLE CONSOLE OPERATION Loop select during “HL, P1, P2, P3”, the function are same with upper console. MODE 13. Display Display the current mode or speed or time. window In manual mode, increase the oscillation & spiral vibration speed at the same time.
EXERCISES Thigh muscles, shins and calves • Stand on the center of the plate and straddle it slightly. • Bend your knees at an angle of 20 - 80 degrees. • The knees bent should not be further than the toes. Hind thigh muscles •...
Page 15
Abdominal muscles and thigh area • Sit on a mat and bend your legs. • Stand on the mat and touch the ankle. • Wrap the pillar with your thighs, then tighten the thighs on the mat (strengthening the belt). •...
MAINTENANCE HOW TO STORE 1. Do not store the Vibration Plate: • Near heat or open flame. • Under the direct sunlight for a long period time. • Harmful gas and dust, especially humidity. 2. Keep the Vibration Plate: • Usage temperature: 0-35℃.
Speed Range 1-60 level Display Program / Time / Speed Dimensions 730mm (L) X 700mm(W) X 1450mm (H) Load Weight 150KGS Net Weight 36KGS Gross Weight 40KGS ENVIRONMENT PROTECTION After the product lifespan expired or if the possible repairing is uneconomic, dispose it according to the local laws and environmentally friendly in the nearest scrapyard.