Related Manuals for MEGATRONIX Megalarm MEGA 2500
Summary of Contents for MEGATRONIX Megalarm MEGA 2500
- Page 1 MEGA 2500 2-WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation Manual MEGATRONIX CALIFORNIA, U.S.A. MEGA 2500 INSTALL...
- Page 2 MEGA 2500 INSTALL...
-
Page 3: Installation Diagram
INSTALLATION DIAGRAM H8 10 Pin H1: Main 5 Pin White Harness H1 5 Pin White H8: 10 Pin White Mini Connector White Two Way Paging Transceiver H2 3 Pin H7 4 Pin Sensor Brown Antenna Black (Optional) H3 2 Pin Valet Switch Dual Zone Blue... - Page 4 Keep wiring away from moving engine parts, exhaust pipes, and high-tension cable. Tape wires that pass through holes on the firewall to prevent frying electrical. Watch out for sharp edges that may damage wires and causes short circuit. CAUTION: Do not connect the wire harness to the control module until all wiring to vehicle is complete. H1.
- Page 5 H8/2. Blue / White wire – (-) Instant Trigger or Major trigger Input (Zone 2) – This wire is the ground trigger input wire for hood/trunk pin switches. H8/3. Violet wire – Positive Door Switch Sensing Input – This wire is the positive trigger input wire for positive door pin switch. This wire is the connection for "positive"...
- Page 6 H4. 6 PIN DOOR LOCK HARNESS: INSTALL NEW DOOR LOCK MOTORS Blue/Red Wire: (87a) - Door Unlock Relay Green/ white Blue/White Wire: (30) - Door Unlock Relay Blue/ white Blue/Yellow Wire: (87) - Door Unlock Relay Blue/ red Green/Red Wire: (87a) - Door Lock Relay Green/ red Green/White Wire: (30) - Door Lock Relay Blue/ yellow...
- Page 7 2 STEP DOOR UNLOCK WIRE CONNECTION FOR 2 STEP DOOR UNLOCK WIRE CONNECTION FOR GROUND SWITCHED DOOR LOCKS POSITIVE SWITCHED DOOR LOCKS LT. Green / Black +12V OEM Door Master Lock Switch OEM Door Master Lock Wire Switch LT. Green / Unlock Lock Black Wire...
-
Page 8: Alarm Features Programming
PROGRAMMING A. THE TRANSMITTERS: Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is exceeded, the security system will start deleting transmitters from the memory in chronological order. 1. Turn the Ignition switch ‘OFF/ON’ 3 TIMES and stay in the ON position. Within 15 seconds. 2. - Page 9 Parking light “on” for Parking light “on” for 30 seconds upon an Pathway 30 seconds upon an unlock signal & 10 illumination unlock signal seconds upon a lock feature “off” signal. Exit: Turn Ignition to the 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit. Comfort Feature: Some Vehicles have a special “COMFORT feature”.
- Page 10 Latched output: The latched output selection will output a negative signal as soon as the Channel 3 (4) button is pressed and will continue until the button is pressed again. Latched output / reset with ignition: The latched / reset with ignition output selection operates just like the latched output but will reset or stop when the ignition is turned on.
- Page 11 Enter: 1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in the OFF position. 2. Push the Valet switch 8 times and hold it on the 8 push until four chirps with a long chirp is heard. Then release the valet switch. You are now in the Alarm feature ‘IV’ programming mode. 3-a.
- Page 12 MEGA 2500 INSTALL...
Need help?
Do you have a question about the Megalarm MEGA 2500 and is the answer not in the manual?
Questions and answers