Subscribe to Our Youtube Channel
Related Manuals for Edge EDS500.2FD-E0
Summary of Contents for Edge EDS500.2FD-E0
- Page 1 User Manual power amplif iers Автомобильные усилители eds500.2fd-e0 eds3000.1fd-e0...
- Page 2 Thank you for buying EDGE, we hope you enjoy listening to your product as much as we enjoyed creating it.
-
Page 3: Limited Warranty
EDGE. Graphics and logos are trademarks or trade dress of EDGE audio or its subsidiaries. EDGE’s trademarks and trade dress may not be used in connection with any product or service that is not EDGE’s, in any manner that is likely to cause confusion among cus- tomers or in any manner that disparages or discredits EDGE. -
Page 4: Mounting Guidelines
Mounting Guidelines Your EDGE amplifier is designed with a swift installation routine in mind. Please mount the amplifier in a dry location on a solid surface. NEVER mount the amplifier upside down as this will cause the amplifier to over heat and will eventually damage the amplifier. -
Page 5: Power Cable
Power Cable • At least 4 gauge cable should be used for the power connection to the amplifier. • The power cable should be taken directly from the battery. Rubber grommets should be used when passing through any bulkheads to prevent the cable from becoming chaffed or cut. - Page 6 EDS500.2FD Terminals And Connections 1. Low level input For connection to any source (head unit) with a low level output. This is your RCA output from the source (headunit) 2. High Pass Filter (HPF) This control is used to set the HPF crossover frequency for the amplifier. The frequency is adjustable between 15Hz and 1kHz.
-
Page 7: Amplifier Configuration
Amplifier Configuration Minimum impedance 1Ω per channel Minimum impedance 2Ω Minimum impedance 1Ω per channel WARNING Driving multiple speakers at an impedance lower than that recommended by EDGE could cause damage to this amplifier that is not covered by warranty. - Page 8 EDS3000.1FD Terminals And Connections OUTPUT 1. Low level input / output For connection to any source (head unit) with a low level output. This is your RCA output from the source (headunit). The output is used to daisy chain to another EDS3000.1FD. 2.
- Page 9 Multi Amplifier Installation Amplifier Configuration Minimum impedance 1Ω Minimum impedance 1Ω WARNING Driving multiple speakers at an impedance lower than that recommended by EDGE could cause damage to this amplifier that is not covered by warranty.
-
Page 10: Set Up Section
By using the crossovers correctly you will not only lengthen the life of your speakers but you will also get better performance from them. To optimise your setup seek the advice of a professional installation engineer or visit your local VIBE audio dealer. Specification Model EDS500.2FD-E0 EDS3000.1FD-E0 Configuration 2 channel Monoblock Dimensions 63mm (2.5”) x 125mm... - Page 11 UK Technical Enquiries Call 09067031420 Calls cost 50p per minute. Call costs correct at date of publication (01/02/12) Hours of business 9.00am - 5.30pm GMT Monday - Friday. All calls are recorded for training purposes. MIDBASS Distribution PO Box 11000 B75 7WG International Technical Enquiries For international technical support please contact the...
- Page 14 Battery...
- Page 15 • • • • • • • • • • •...
- Page 18 EDS3000.1FD Разъемы и органы управления Низкоуровневый вход/выход Используется для подсоединения источника сигнала (головного устройства) с низкоуровневым выходом. Подключение производится к RCA выходу на головном устройстве. Выход используется для последовательного подключения EDS3000.1FD. Настройка фильтра НЧ кроссовера (HPF) Данная настройка устанавливает полосу НЧ усилителя. Регулировка в пределах 15 Гц –...
- Page 19 Подключение нескольких усилителей Подключения ОСТОРОЖНО! Подключение нескольких нагрузок с сопротивлением меньшим, чем рекомендует EDGE может вызвать поломку усилителя, не подпадающую под гарантийные обязательства поставщика.
- Page 20 • • • • • •...
- Page 21 Товар подлежит декларированию соответствия -10-...
- Page 22 Technical Update : EDS3000.1FD-E0 / EDX5000.1FD-E0 The EDGE Monoblock amplifiers (EDS3000.1FD-E0 / EDX5000.1FD-E0) have been updated with audio pass though on the low level inputs (RCA). This allows the audio signal to be passed from one amplifier to another without the need for RCA Y-splitters.
- Page 23 техническое обновление : EDS3000.1FD-E0 / EDX5000.1FD-E0 Одноканальные Усилители EDGE (EDS3000.1FD-E0 / EDX5000.1FD-E0) Добавлено последовательное соединение аудиосигнала на входах низкого уровня (RCA). Это позволяет передавать аудиосигнал от одного усилителя к другому без необходимости использования Y-разветвителей RCA. При использовании сквозного аудиосигнала используется правый вход для вывода...
- Page 24 edgecaraudio.com facebook.com / EDGEaudio instagram.com / edge_caraudio...
Need help?
Do you have a question about the EDS500.2FD-E0 and is the answer not in the manual?
Questions and answers