Related Manuals for Edge XTREME EDX1800.2FD-EO
Summary of Contents for Edge XTREME EDX1800.2FD-EO
- Page 1 revolutionary car audio User Manual power amplif iers Автомобильные усилители edx1800.2fd-e0 edx800.4fd-e0 edx5000.1fd-e0...
- Page 2 Thank you for buying EDGE, we hope you enjoy listening to your product as much as we enjoyed creating it.
-
Page 3: Limited Warranty
EDGE. Graphics and logos are trademarks or trade dress of EDGE audio or its subsidiaries. EDGE’s trademarks and trade dress may not be used in connection with any product or service that is not EDGE’s, in any manner that is likely to cause confusion among cus- tomers or in any manner that disparages or discredits EDGE. -
Page 4: Mounting Guidelines
Mounting Guidelines Your EDGE amplifier is designed with a swift installation routine in mind. Please mount the amplifier in a dry location on a solid surface. NEVER mount the amplifier upside down as this will cause the amplifier to over heat and will eventually damage the amplifier. -
Page 5: Power Cable
Power Cable • At least 4 gauge cable should be used for the power connection to the amplifier. • The power cable should be taken directly from the battery. Rubber grommets should be used when passing through any bulkheads to prevent the cable from becoming chaffed or cut. - Page 6 EDX1800.2FD Terminals And Connections 1. Low level input For connection to any source (head unit) with a low level output. This is your RCA output from the source (headunit) 2. High Pass Filter (HPF) This control is used to set the HPF crossover frequency for the amplifier. The frequency is adjustable between 15Hz and 1kHz.
-
Page 7: Amplifier Configuration
Amplifier Configuration Minimum impedance 1Ω per channel Minimum impedance 2Ω Minimum impedance 1Ω per channel WARNING Driving multiple speakers at an impedance lower than that recommended by EDGE could cause damage to this amplifier that is not covered by warranty. - Page 8 EDX800.4FD Terminals And Connections 11 12 1. Low level input For connection to any source (head unit) with a low level output. This is your RCA output from the source (headunit) 2. CH1/2 High Pass Filter (HPF) This control is used to set the HPF crossover frequency for the amplifier. The frequency is adjustable between 15Hz and 1kHz.
- Page 9 Minimum impedance 1Ω Minimum impedance 1Ω Minimum impedance 1Ω per channel Minimum impedance 1Ω per channel WARNING Driving multiple speakers at an impedance lower than that recommended by EDGE could cause damage to this amplifier that is not covered by warranty.
- Page 10 EDX5000.1FD Terminals And Connections OUTPUT 1. Low level input / output For connection to any source (head unit) with a low level output. This is your RCA output from the source (headunit). The output is used to daisy chain to another EDX5000.1FD. 2.
- Page 11 Multi Amplifier Installation Amplifier Configuration Minimum impedance 1Ω Minimum impedance 1Ω WARNING Driving multiple speakers at an impedance lower than that recommended by EDGE could cause damage to this amplifier that is not covered by warranty.
-
Page 12: Set Up Section
Set Up Section To correctly set the gain control of the amplifier to match that of the source (headunit) use the following setup routine: Turn the gain control to minimum on the amplifier. Ensure the bass boost is set to 0 dB. On the headunit set all crossovers (if applicable) to flat and both bass and treble to zero. - Page 13 UK Technical Enquiries Call 09067031420 Calls cost 50p per minute. Call costs correct at date of publication (01/02/12) Hours of business 9.00am - 5.30pm GMT Monday - Friday. All calls are recorded for training purposes. MIDBASS Distribution PO Box 11000 B75 7WG International Technical Enquiries For international technical support please contact the...
- Page 15 Battery...
- Page 16 • • • • • • • • • • •...
- Page 17 11 12...
- Page 22 EDX5000.1FD Разъемы и органы управления OUTPUT Низкоуровневый вход/выход Используется для подсоединения источника сигнала (головного устройства) с низкоуровневым выходом. Подключение производится к RCA выходу на головном устройстве. Выход используется для последовательного подключения EDX5000.1FD. Настройка фильтра НЧ кроссовера (HPF) Данная настройка устанавливает полосу НЧ усилителя. Регулировка в пределах 15 Гц –...
- Page 23 Подключение нескольких усилителей Подключения Minimum impedance 1 Minimum impedance 1 ОСТОРОЖНО! Подключение нескольких нагрузок с сопротивлением меньшим, чем рекомендует EDGE может вызвать поломку усилителя, не подпадающую под гарантийные обязательства поставщика.
- Page 24 • • • • • • -12-...
- Page 25 -13-...
- Page 26 Notes:...
- Page 27 Notes:...
- Page 28 edgecaraudio.com facebook.com / EDGEaudio instagram.com / edge_caraudio...
Need help?
Do you have a question about the XTREME EDX1800.2FD-EO and is the answer not in the manual?
Questions and answers