Table of Contents
Advertisement
a The time or residual heat indicator appears on the
display.
8.3 Starting the operation
You must start each operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
Do not use the appliance if there is water on the
▶
cooking compartment floor.
Wipe away any water on the cooking compartment
▶
floor before operation.
Use
to start the operation.
▶
a The settings appear on the display.
8.4 Interrupting the operation
You can interrupt the operation and then continue
again.
To interrupt the operation, press
1.
Press
again to resume operation.
2.
8.5 Setting an operating mode
After you have switched on the appliance, the menu
appears on the display.
To scroll through the various selection options,
1.
swipe to the left or right on the display.
To select a function, press the corresponding tile.
2.
a Depending on the function, possible adjustment val-
ues or other tiles are available for selection.
If required, press on another tile.
3.
To change the adjustment values:
4.
Swipe over the blue adjustment line or push the
‒
adjustment line to the appropriate point.
Or press
and enter the value directly via the
‒
number field that appears.
5.
Use
to start the operation.
If the operation is ended:
6.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Tip: You can save your settings as "Favourites"
use these again.
→ "Favourites", Page 20
8.6 Setting the type of heating and the
temperature
Press "Types of heating".
1.
Press the type of heating that you want to use.
2.
Set the temperature using
3.
ment bar. Or enter the temperature directly via the
number field
.
If required, you can implement additional settings:
– → "Rapid heating", Page 14
– → "Time-setting options", Page 14
– → "Steaming", Page 15
4.
Use
to start the operation.
a The appliance starts heating.
.
to switch the ap-
and
or
or via the adjust-
a The adjustment values and how long the appliance
has already been in operation are shown on the dis-
play.
When the food is ready, use
5.
ance off.
Note: The most suitable type of heating for your food
can be found in the type of heating description.
→ "Types of heating", Page 8
Changing the type of heating
When you change the type of heating, the other set-
tings are also reset.
Press
.
1.
Press
.
2.
Press the type of heating that you want to use.
3.
Reset the operation and use
4.
Changing the temperature
Once the operation has started, you can change the
temperature at any time.
Press the temperature.
1.
Change the temperature using
2.
justment bar. Or enter the temperature directly via
the number field
.
Press "Apply".
3.
8.7 Displaying information
In most cases, you can call up information about the
function that you have just started. The appliance auto-
matically displays certain information, e.g. to ask you to
do/confirm something or to issue a warning.
Press .
1.
a If information is available, this is displayed for a few
seconds.
If there is a lot of content in the tile, scroll using
2.
or
.
If required, close the notification using
3.
8.8 Sabbath-compliant use
If you want to operate your appliance so that it is Sab-
bath-compliant, use the time-setting options and
change the basic setting for the lighting.
Note: If you open the appliance door during operation,
the appliance stops heating. When you close the appli-
ance door, the appliance continues to heat again. To
operate your appliance so that it is Sabbath-compliant,
do not open the appliance door until after operation.
Change the "Lighting" basic setting to "Always off".
1.
→ "Basic settings", Page 21
This will ensure that the light in the cooking com-
partment is always off while the appliance is in oper-
ation and when you open the appliance door.
Set the required operating mode.
2.
→ "Setting an operating mode", Page 13
→ "Setting the type of heating and the temperature",
Page 13
Set the required cooking time depending on the op-
3.
erating mode.
→ "Setting the cooking time", Page 14
→ "Time-setting options", Page 14
Use "End time" to set the time at which the opera-
4.
tion should end.
→ "Setting the end time", Page 15
Basic operation en
to switch the appli-
to start.
or
or via the ad-
.
13
Advertisement
Table of Contents
