Page 1
Quick Reference Guide of WebEye B106 This information is to connect WebEye B106 on Internet of dedicated line or local LAN. For different lines like xDSL, cable and ISDN, please visit Download page in WebGate Internet homepage and download related information.
Page 2
Quick Reference Guide of WebEye B106 I. Monitoring of real-time images through WebEye B106 1. PC and LAN requirements 1.1 PC requirements l CPU: Pentium II and above l RAM: 64MB and above l O/S: Windows 98/NT/Me/2000 1.2 Check display setting in your PC.
Page 3
Quick Reference Guide of WebEye B106 5. Go to ‘Gateway’. 7. Go to ‘IP Address’ 6. Check gateway address. Check address and subnet mask. 1.4 Internet Browser Requirements l Internet Explorer 5.0 and above l Netscape Navigator 4.7 and above 1.5 Check LAN...
Page 4
Quick Reference Guide of WebEye B106 Note in connecting cable to terminal block When you connect cable to terminal block, you should peel off the cov er of cable by 1.5Cm and insert the cable by 2Cm into the terminal block.(communication., sensor, alarm and etc) In case of power cable, the white mark of two lines means ‘+’.
Page 5
Quick Reference Guide of WebEye B106 * Crossover Cable and Direct Cable * The crossover cable (red) provided with the WebEye is used to connect the WebEye with a PC. A HUB is not necessary to connect the WebEye to a PC if a crossover cable is used. The direct cable (white) should be used if a HUB is used as an intermediary between the WebEye and PC.
Page 6
Quick Reference Guide of WebEye B106 1. Select the default IP address of WebEye (211.53.133.91). 5. After changing IP address, the new IP address appears. Click on the IP address. 2. & 6. The selected IP address appears (211.53.133.91). 3. Enter Admin’s password.
Page 7
Quick Reference Guide of WebEye B106 l Please note!! When an IP address is assigned to the WebEye, be careful not to ass ign the WebEye with an IP address that is not compatible with the local network or that is already in use by another computer or similar device. Please refer below example and assign an IP address to WebEye.
Page 8
Quick Reference Guide of WebEye B106 5.1 Select ‘Network Configuration’ in the menu and configure. 1. Click ‘Ethernet’ button. 2. Check if IP address is same as assigned at 3. Set Netmask. Setup program. 4.This button makes WebEye set broadcast 5.
Page 9
Quick Reference Guide of WebEye B106 6. Access WebEye image viewer and configure watching condition 1. Enter IP address of your WebEye in the address bar of the Web browser (e.g. http://192.168.1.51) and press ‘Enter ’ key. 6.1 Enter IP address and access WebEye image viewer 5.
Page 10
Quick Reference Guide of WebEye B106 3. Click ‘Download WebEye Plug-in Now!’ button. * This step is for Netscape Navigator users only. Internet Explorer users can skip this step. 4. Click ‘Grant’ button. ‘Install Successfully Completed’ will appear. * This step is for Explorer user s only.
Page 11
If you experience a case that Active-X for Internet Explorer or Plug-in for Netscape Navigator is not installed into your PC properly, please visit ‘Download’ page in WebGate Internet homepage (http://www.webgateinc.com). And download a program to install Active-X or Plug-in manually.
Page 12
Quick Reference Guide of WebEye B106 Set the desired viewer option. S imple viewer, server- push viewer, java applet viewer viewer configurations are available in this menu. For more information, please refer to User ’s guide. Resolution, image size, and Images can be viewed in this section.
Page 13
Quick Reference Guide of WebEye B106 II. Connecting external camera. 1. Functions of DIP switch. D I P S w i t c h H i - z 7 5 o h m 7 5 o h m To designate video signal termination. To connect external CCTV cameras , place the switches in proper positions.
Page 14
Quick Reference Guide of WebEye B106 2.2 Connecting external camera to WebEye 2.2.1 CH #1 l Enter WebEye administrator’s page l Enter ‘Video Configuration’ page and configure. 1. Enter ‘Video Configuration’ page 3. Choose ‘Color ’ or and select ‘Video Channel #1’...
Page 15
Quick Reference Guide of WebEye B106 2.2.2 CH #2 l Enter WebEye administrator’s page. l Enter ‘Video Configuration’ page and configure. 1. Enter ‘Video Configuration’ page 3 . Choose ‘Color ’ or and select ‘Video Channel #2’ ‘B/W’ according among 6 channels.
Page 16
Quick Reference Guide of WebEye B106 2.2.3 CH #3 l Enter WebEye administrator’s page l Select ‘Video Channel 3’ in ‘Video Channel Selection’ menu. l Connect external camera and check DIP switches ’ position D I P S w i t c h...
Page 17
Quick Reference Guide of WebEye B106 2.2.3 CH #5 l Enter WebEye administrator’s page l Select ‘Video Channel 5’ in ‘Video Channel Selection’ menu. l Connect external camera and check DIP switches ’ position D I P S w i t c h...
Page 18
Quick Reference Guide of WebEye B106 1.4. Connecting many of external cameras to WebEye 1.4.1 Connection diagram Video signal flows through LAN Cable. Video signal flows through BNC Cable. CCTV Camera In this application, user should designated to ‘on(down)’ DIP switch of external camera connect to WebEye.
Page 19
Quick Reference Guide of WebEye B106 1. Enter ‘Video Configuration’ page 3 . Choose ‘Color’ or and select ‘Video Channel #2’ ‘B/W’ according among 6 channels. external camera type. 2. Select ‘Enable’ to use th is channel. 4. Choose proper type between NTSC and PAL.
Page 20
Quick Reference Guide of WebEye B106 1. Enter ‘Video Configuration’ page 3. Choose ‘Color ’ or and select ‘Video Channel #5’ ‘B/W’ according among 6 channels. external camera type. 2. Select ‘Enable’ to use th is channel. 4. Choose proper type between NTSC and PAL.
Page 21
Quick Reference Guide of WebEye B106 3.2.8 Connecting CCTV monitor with a multiplexer or auto-selector l If a multiplexer or auto-selector is used, a CCTV monitor will be enough for 6 channels. l Some multiplexers or auto-selectors don’t have DIP switch nor are designated to set termination.
Page 22
Quick Reference Guide of WebEye B106 III. Connecting WebEye through firewall. 1. WebEye is blocked with firewall. l If there is a firewall in the network where WebEye is connected, enter WebEye administrator’s page and change TCP ports. 1. If default port (80) is blocked, change...
Page 23
Quick Reference Guide of WebEye B106 2. User’s PC is blocked with firewall. l If there is a firewall on the network where your PC is connected, enter WebEye login page with IP address (ex: http://192.168.1.51). l Enter ID and password.
Page 24
Quick Reference Guide of WebEye B106 For more detailed information on how to install PTZ mechanism, auto iris lens, external sensor and relay, please visit ‘Download ’ page in WebGate Internet homepage and download related information. http://www.webgateinc.com...