Fine Setting Of The Components - RCA RTD101 User Manual

RTD101-EN receiver 11/25/02
Advanced Sound Control
Stereo
The Stereo mode uses the two main channel outputs from
the front speakers.

Fine Setting of the Components

The receiver has pre-selected the best surround mode for
you once you turn on the unit by pressing the SOURCE
Buttons (like DVD/CD, SAT) directly. The default surround
modes for different components are as tabled below.
If you decide to change the surround mode, you can press
the SURROUND repeatedly to toggle among the different
surround mode choices and select the one you want.
For Digital Signal (2ch PCM), or analog signal , VCR,
Tuner:
Dolby PL II Movie
Emulation Dolby 3 Stereo
Theater Stadium
For Digital Signal (Dolby Digital)
Dolby Digital Dolby 3 Stereo
II Movie Dolby PLII Music
For DTSl Signal
DTS Stereo
Default Settings
The receiver will keep the last selection in memory as long
as it doesn't enter standby mode.
Input Signal Setting
The receiver defaults to the most convenient settings for
your easiest use (see table).
Source/ If Digital Input
Source/ (optical or coaxial)
Input is selected
DVD/CD Dolby Digital
SAT Dolby Digital/
VCR N/A
TUNER N/A
By default, SAT (satellite) is set to analog input. If you wish
to change the input formats, follow the steps below:
1. Press SOURCE on the main unit until SAT appears on the
display or press the SAT/CAB source buttons on the remote
control.
2. Press AUDIO on the remote control to toggle among
optical analog to match your connection. Your selection will
be stored automatically.
Every time you press the source button, the input setting
SOURCE DEFAULT INPUT (as seen on display)
SAT
Analog (SAT/ ANL)
VCR Analog (VCR)
FM/AM Built-in Tuner
DVD/CD Built-in
(e.g. SAT/ ANL) will be shown on display for a few seconds.
Note: Only SAT input can be changed to optical input.
16
10:09 AM Page 20
Dolby PL II Music Dolby PL
Arena Jazz Club
Disco Stereo
Stereo Dolby PL
Dolby PL Emulation
If PCM If Analog Input
bitstream selected
PRO-LOGIC II N/A
MOVIE
PRO-LOGIC II PRO-LOGIC II MOVIE
MOVIE
N/A PRO-LOGIC II MOVIE
N/A PRO-LOGIC II MUSIC
SOURCE AVAILABLE INPUT
SAT ANL/Optical
DVD/CD Built-in
VCR ANL
TUNER Built-in
Digital Input: Optical (OPT)
Select this setting to play digital signals from a DVD, CD, LD
player, or SAT. (SAT mode only)
Analog Input
Select this setting to play analog signals from a cassette
deck, VCR or SAT.
DSP (Digital Sound Processor)
These digital sound effects resemble sounds in a real
environment such as Arena, Jazz Club, Theater, Stadium
and Disco. DSP automatically converts analog audio signals
to digital ones which enables you to adjust the sound with-
out degrading the sound quality. Different modes will give
you different feel of size and type of listening environment.
(Not available in Dolby Digital and DTS (DVD))
Night Mode
By using Dynamic Range Compression technology, you can
enjoy enhanced Dolby Digital sound quality at night with-
out interrupting your roommates or neighbors. Night Mode
will compress the difference in volume between normal
voices and sound like explosions, while still enjoying a
Dolby Digital enable component (DVD, SAT). Night Mode
can be activated by press and hold the OK button, DRC
SOFT (Default) will appear on the display. While DRC SOFT
(Default) is still on the display, press the LEFT or RIGHT
Adjustment buttons l,around the OK button, until you
select the desired mode. There are three modes (OFF, SOFT,
SOFTER) for you to choose the extents of compression.
NOTE
SAT and VCR are just generic names. You can connect
other compatible audio/video components to these
inputs like TV, TAPE, MINI DISC, CD-RW player, etc.