Woods DS12.50 Operator's Manual page 41

DS1260 & DS1440 Pull-Type Assembly
(Continued)
FRONT HALF
(Figure 29)
Install Tongue
1. Place tongue (1) between mast plates.
2. Place washer (26†) and sleeve (16) on cap screw
(25).
3. Place washer (26) between mast plates and
tongue, insert cap screw (25) with washer (26) and
sleeve (16) through mast plates and tongue.
4. Secure with washer (26) and lock nut (27).
5. Attach front half of attitude rod (18) to lug on
tongue using clevis pin (17) and cotter pin (33).
6. Raise front of cutter and install parking jack (6) to
support tongue.
7. Attach safety tow chain (5) to tongue by wrapping
chain around diagonal brace and threading the
hook end back through the large link on opposite
end of chain.
Install 3-Joint Driveline
Install Driveline
1. Coat input shaft of gearbox with a light coating of
grease.
2. Attach slip clutch on driveline (9) to input shaft of
gearbox. Tighten cap screws (19) and lock nuts
(20).
3. Attach rear tether chain on driveline to clip on
plastic gearbox shield.
Install H-Frame
1. Place H-frame (2) in correct hole in bottom of
tongue to maintain proper PTO distance (see
Figure 29).
2. Secure H-frame to tongue using cap screw (23),
two sleeves (3), two cup washers (4) and lock nut
(24).
Attach Driveline to H-Frame
NOTE: Select holes in H-frame that will allow driveline
to run level. Refer to Operation section for driveline
height. Final adjustment will be necessary when cutter
is attached to the tractor.
Place driveline bearing carrier between H-frame (2)
and secure with clevis pin (7) and cotter pin (28).
Install Front Drive
1. Slide rear yoke of front driveline (8) over shaft of
driveline (9) and align with notch on shaft.
MAN0571 (Rev. 6/15/2007)
(Figure 29)
2. Secure drives together using cap screw (21) and
lock nut (20).
3. Attach tether chain on front half of driveline (8) to
H-frame (2).
Install Drive Shield & Hose Holder
1. Attach drive shield (13) to driveline carrier bearing
using two cap screws (32) and lock washers (31).
2. Attach hydraulic hose holder (15) to the top hole in
H-frame (2) with cap screw (22), spacer (14), and
lock nut (29).
INSTALL CV DRIVELINE (OPTIONAL)
Install Driveline
(Figure 30)
1. Coat input shaft of gearbox with a light coating of
grease.
2. Attach slip clutch on driveline (6) to input shaft of
gearbox. Tighten cap screws (14) and lock nuts
(15).
3. Attach rear tether chain on driveline to clip on
plastic gearbox shield.
Install H-Frame
1. Attach H-frame mounting bracket (13) to cutter
frame with carriage bolts (23), washers (24) and
lock nuts (21).
2. Place H-frame (2) over bracket and align holes.
3. Secure H-frame to bracket using cap screw (18),
two sleeves (3), two cup washers (4), and lock nut
(19).
Attach Driveline to H-Frame
NOTE: Select holes in H-frame that will allow driveline
to run level. Refer to Operation section for driveline
height. Final adjustment will be necessary when cutter
is attached to the tractor.
Place driveline bearing carrier between H-frame (2)
and secure with clevis pin (5) and cotter pin (20).
Install CV Drive
1. Slide rear yoke of CV driveline (1) over shaft of
driveline (6) and align with notch on shaft.
2. Secure drives together using cap screw (16) and
lock nut (15).
Install Drive Shield & Hose Holder
1. Attach drive shield (10) to driveline carrier bearing
using two cap screws (26) and lock washers (25).
2. Attach hydraulic hose holder (12) to the top hole in
H-frame (2) with cap screw (17), spacer (11), and
lock nut (21).
Assembly 41