Table of Contents

Advertisement

Quick Links

LV 5770
LV 5770SER03A
LV 5770SER03
LV 5770SER08
LV 5770SER09(A) SDI INPUT / EYE
LV 5770SER41
LV 5770SER42
LV 5770SER43
INSTRUCTION MANUAL
MULTI MONITOR
TRI SYNC / COMPOSITE
COMPOSITE VIDEO
SDI INPUT
DIGITAL AUDIO
ANALOG AUDIO
DIGITAL AUDIO

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LV 5770 and is the answer not in the manual?

Questions and answers

Summary of Contents for Leader LV 5770

  • Page 1 LV 5770 MULTI MONITOR LV 5770SER03A TRI SYNC / COMPOSITE LV 5770SER03 COMPOSITE VIDEO LV 5770SER08 SDI INPUT LV 5770SER09(A) SDI INPUT / EYE LV 5770SER41 DIGITAL AUDIO LV 5770SER42 ANALOG AUDIO LV 5770SER43 DIGITAL AUDIO INSTRUCTION MANUAL...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS GENERAL SAFETY SUMMARY ..................I INTRODUCTION ......................1 Scope of Warranty ........................1 Operating Precautions ......................1 1.2.1 Maximum Allowable Input Voltage ................... 1 1.2.2 About Standby Mode ....................... 2 1.2.3 Mechanical Shock ......................2 1.2.4 Electrostatic Damage ....................... 2 1.2.5 About the Cabinet ......................
  • Page 3 2.3.21 Analog Composite Signal Picture Display (LV 5770SER03A)........23 2.3.22 SDI Signal 3D-Assist Display (LV 5770SER08 and LV 5770SER09A) ......23 2.3.23 Digital Audio Display (LV 5770SER41 and LV 5770SER43) .......... 24 2.3.24 Analog Audio Display (LV 5770SER42) ................. 27 2.3.25 SDI Signal Status Display (LV 5770SER08 and LV 5770SER09A) ........
  • Page 4 I/O Settings ........................... 68 7.1.1 Configuring SDI Input Settings (LV 5770SER08 and LV 5770SER09A) ......68 7.1.2 Rear Panel Settings ....................... 71 Configuring the LV 5770 ....................... 74 7.2.1 General Settings ......................74 7.2.2 Configuring Ethernet Settings ..................76 7.2.3 Remote Control Settings ....................
  • Page 5 Deleting Presets ........................96 Copying All Presets ....................... 97 9.4.1 Copying All Presets from the LV 5770 to a USB Memory Device ........97 9.4.2 Copying All Presets from a USB Memory Device to the LV 5770 ........98 10. REMOTE CONTROL ....................99 11.
  • Page 6: General Safety Summary

    ■ Note about Reading This Manual The contents of this manual contain specialized terminology and may be difficult to understand. If you have any questions about the contents of this manual, please contact your local LEADER agent. ■ Symbols and Terms The following symbols and terms are used in this instruction manual and on the instrument to indicate important warnings and notes.
  • Page 7 Failing to do so could lead to fire.Turn off the power switch, and remove the power cord from the outlet. After making sure that fire has not spread anywhere, contact your local LEADER agent.
  • Page 8 Using a power cord that does not meet the standards could lead to fire. If the power cord is damaged, stop using it, and contact your local LEADER agent. Using a damaged power cord could lead to electrical shock or fire.
  • Page 9 To ensure stable performance, we recommend that you have the instrument calibrated regularly. Also, if the instrument malfunctions, repairs are necessary. For repairs and calibration, contact your local LEADER agent. ■ Routine Maintenance When you clean the instrument, remove the power plug from the outlet.
  • Page 10: Introduction

    1. INTRODUCTION INTRODUCTION Thank you for purchasing this LEADER instrument. To use this instrument safely, read this instruction manual thoroughly, and make sure that you know how to use the instrument properly. If some point about the operation of this instrument is still unclear after you have read this instruction manual, refer to the contact information on the back cover of the manual to contact LEADER, or contact your local LEADER agent.
  • Page 11: About Standby Mode

    To continually use the last-memory feature, we recommend that you replace the backup battery with a new one every five years after you purchase the instrument. You cannot replace the backup battery yourself. Contact your local LEADER agent.
  • Page 12: About The Lcd Panel

    1. INTRODUCTION 1.2.8 About the LCD Panel There may be a small number of pixels in the LCD panel that do not light or are always on. Note that this is not a malfunction. The LCD panel supports a large number of video signals. SDI input signals are displayed asynchronously on the LCD.
  • Page 13: About Terminology Used In This Manual

    1. INTRODUCTION About Terminology Used in this Manual ● Single Input Mode This refers to the mode in which the SIM key is off. Press the A and B keys to switch between measuring the signal that is being applied to SDI INPUT A and the signal that is being applied to SDI INPUT B, respectively.
  • Page 14: Specifications

    SPECIFICATIONS General The LV 5770 is a waveform monitor that supports 3G-SDI, HD dual link, HD-SDI, and SD-SDI signals. It is light weight and comes at a low cost but has a variety of technically advanced features including simultaneous monitoring of two SDI signals, lip sync measurement, and ANC data analysis.
  • Page 15 Not only can captured data be displayed by the LV 5770, but it can also be compared with an input signal or saved to a USB memory device. It is easy to view the saved data on a PC.
  • Page 16 ● Digital Audio I/O (LV 5770SER41 and LV 5770SER43) When the digital audio I/O option is installed in the LV 5770, the LV 5770 can display the external digital audio in addition to the embedded audio. The eight I/O connectors—16 channels—can be switched between input and output in groups of four connectors—8...
  • Page 17 ● Dolby Option (LV 5770SER41 and LV 5770SER43) The addition of the Dolby option enables the LV 5770 to decode and display the Dolby E or Dolby Digital signals that are compressed in embedded audio or digital audio signals. ●...
  • Page 18: Specifications

    2. SPECIFICATIONS Specifications 2.3.1 SDI Video Signal Formats and Standards (LV 5770SER08 and LV 5770SER09A) Bit Rate 3G-SDI 2.970 Gbps or 2.970/1.001 Gbps HD-SDI 1.485 Gbps or 1.485/1.001 Gbps SD-SDI 270 Mbps Table 2-1 SD-SDI video signal formats and standards Color System Quantization Scanning...
  • Page 19 2. SPECIFICATIONS Table 2-4 3G-SDI level A video signal formats and standards Color System Quantization Scanning Frame (Field) Rates Compliant Standard 4:2:2 10 bits 1080p 60/59.94/50 SMPTE ST 424 SMPTE ST 425 12 bits 1080p 30/29.97/25/24/23.98 1080PsF 30/29.97/25/24/23.98 1080i 60/59.94/50 4:4:4 10 bits 1080p...
  • Page 20 Format Setting Automatic and manual Automatic 3G-SDI and HD Dual Link The LV 5770 detects the format information within the payload ID (SMPTE ST 352) and automatically sets the format. HD-SDI and SD-SDI The LV 5770 determines the format from the input signal's synchronization information and automatically sets the format.
  • Page 21: Embedded Audio Playback Format (Lv 5770Ser41/Lv 5770Ser43 And Lv 5770Ser08/Lv 5770Ser09A)

    2. SPECIFICATIONS 2.3.2 Embedded Audio Playback Format (LV 5770SER41/LV 5770SER43 and LV 5770SER08/LV 5770SER09A) Compliant Standards 3G-SDI, HD-SDI, and HD Dual Link SMPTE ST 299 SD-SDI SMPTE ST 272 Format LPCM, Dolby-E (option), Dolby Digital (option) Quantization 24 bits Clock Generation Generated from the video clock Synchronization All audio channels must be synchronized with the video...
  • Page 22: Analog Video I/O Connectors (Lv 5770Ser03A)

    2. SPECIFICATIONS SDI Output Output Connectors Two BNC connectors Output Signal Serial reclocked input SDI signal 3G-SDI, HD-SDI, and SD-SDI 1 output (switchable between channels A and B) 1 output (fixed to channel B) HD Dual Link 1 output (link channel A or B) Output Impedance 75 Ω...
  • Page 23: Audio I/O Connectors (Lv 5770Ser41, Lv 5770Ser42, And Lv 5770Ser43)

    2. SPECIFICATIONS 2.3.7 Audio I/O Connectors (LV 5770SER41, LV 5770SER42, and LV 5770SER43) I/O connectors of the digital audio (LV 5770SER41 and LV 5770SER43) I/O Connector BNC connector Group A 4 connectors, 8 channels Group B 4 connectors, 8 channels I/O Switching Switching between the connections (4 connectors, 8 channels)
  • Page 24: Video Output Connectors

    2. SPECIFICATIONS 2.3.8 Video Output Connectors DVI-D Output Connector Output Connector One DVI-D connector Output Signal Digital signal of the LCD display Resolution XGA (1024 × 768) Aspect Ratio Signal Format Single link TMDS Not supported HOT PLUG Detection Not supported Picture Monitor Output Connector (LV 5770SER08 and LV 5770SER09A)(*1) Output Connector Output Signal...
  • Page 25: Lcd

    LV 5770 can load. Data Input Data saved to USB memory can be loaded and displayed on the LV 5770. 2.3.12 Frame Capture (LV 5770SER08 and LV 5770SER09A) Function...
  • Page 26: Presets

    Preset Loading Method Front panel, remote control connector (*2), or ethernet Copying All preset data can be copied from the LV 5770 to a USB memory device or from a USB memory device to the LV 5770. Settings related to whether the instrument is on or off, the ethernet connector, the remote control connector, the date, and the time are not saved.
  • Page 27 2. SPECIFICATIONS Display Colors Seven colors to choose from; a different color for each input channel Vertical Axis Gain ×1, ×5 Variable Gain ×0.2 to ×2 Amplitude Accuracy ×1 ±0.5 % ×5 ±0.2 % 3G-SDI, HD Dual Link (1080p/60, 1080p/59.94, 1080p/50) Y Signal ±0.5 % for 1 to 60 MHz Signal...
  • Page 28: Analog Composite Signal Video Waveform Display (Lv 5770Ser03A)

    2. SPECIFICATIONS 2.3.16 Analog Composite Signal Video Waveform Display (LV 5770SER03A) Waveform Operations Line Select Selected line display Sweep Mode H, V Display Color Seven colors to choose from Vertical Axis Scale Composite Signal NTSC -40 to 100 IRE -0.3 to 0.7 V HD Tri-level Sync Signal -0.3 to 0.7 V, -43 to 100 % (the unit is switchable between V and %)
  • Page 29: Sdi Signal Vector Waveform Display (Lv 5770Ser08 And Lv 5770Ser09A)

    2. SPECIFICATIONS 2.3.17 SDI Signal Vector Waveform Display (LV 5770SER08 and LV 5770SER09A) Simul Mode Display Format Mixed, tiled Display Colors Seven colors to choose from; a different color for each input channel Blanking Interval(*1) Masked Pseudo-Composite Display Artificially converts component signals into composite signals and displays the result Line Select Selected line display...
  • Page 30: Sdi Signal 5-Bar Display (Lv 5770Ser08 And Lv 5770Ser09A)

    2. SPECIFICATIONS 2.3.19 SDI Signal 5-Bar Display (LV 5770SER08 and LV 5770SER09A) Simul Mode Display Format Tiled only Function Converts an SDI signal into Y, R, G, B, and composite values and then displays the five peak levels Channel Assignment RGB, GBR Scale mV, %...
  • Page 31 2. SPECIFICATIONS Percentage Display Displays luminance or RGB components as percentages Level Display Displays RGB components with 256 levels (8 bits) Measured points Measurement sizes 1 pixel, 3 × 3 pixels, or 9 × 9 pixels CINELITE Advanced Display Features Synchronized marker display, vector marker display Synchronized Marker Display Synchronizes the markers on the vector display or waveform display to the measurement points of the...
  • Page 32: Analog Composite Signal Picture Display (Lv 5770Ser03A)

    2. SPECIFICATIONS 2.3.21 Analog Composite Signal Picture Display (LV 5770SER03A) Quantization 8 bits Display Sizes Fit, full frame, real, ×2 Frame Rate The frame rate is converted and displayed using the internal sync signal Aspect Marker Display 16:9, 14:9, 13:9 Aspect Marker Format Line, shadow (99 levels), black Safety Marker Size...
  • Page 33: Digital Audio Display (Lv 5770Ser41 And Lv 5770Ser43)

    2. SPECIFICATIONS signal for the right eye on a time sharing display Inverted Display Horizontal Inversion Inverts the picture and video signal waveform (*1) Vertical Inversion Inverts the picture Inverted Channel Inverts video signal for the left eye and video signal for the right eye separately Grid Display Description...
  • Page 34 1 to 5000 ms Parity Error Counts the number of times that the input signal's parity bit and the parity bit recalculated by the LV 5770 differ Validity Error Counts the number of times that the input signal's validity bit is 1...
  • Page 35 2. SPECIFICATIONS Loudness Display Function Loudness chart display, numeric display, log, level meter display (*1), peak value display (*1) Compliant Standard ITU-R BS.1770, ARIB TR-B32, EBU R128, ATSC A/85 Measurement Channel Simultaneous measurement of two audio sources (*1) Mode (Main) Monaural, stereo, 5.1, user specified channel Mode (Sub)(*1) Off, monaural, stereo...
  • Page 36: Analog Audio Display (Lv 5770Ser42)

    2. SPECIFICATIONS 2.3.24 Analog Audio Display (LV 5770SER42) Input Signal Analog audio input Displayed Channels Up to 8 channels Display Type Level meter, Lissajous, surround, status, loudness Level Meter Display The specifications other than those listed here are the same as the digital audio specifications Scale Reference Level Scales 4 dBu to -20 dBFS Level Accuracy...
  • Page 37 2. SPECIFICATIONS to 3FFh in locations other than TRS and ADF Dual Link Phase Difference Error Detects errors when the phase difference between links A and B is 100 clocks or more Cable Length Measurement Error (LV 5770SER09A) Displays an error if the specified cable length is exceeded 3G-SDI 10 to 105 m, 5 m steps...
  • Page 38: Analog Composite Signal Status Display (Lv 5770Ser03A)

    Horizontal ±1 line 2.3.27 Event Log (LV 5770SER08, LV 5770SER09A, LV 5770SER41, and LV 5770SER43) Function Records detected errors, events—such as the LV 5770 switching between input signals, and time stamps. Recording Capacity Up to 1000 events Operation Records all events from start to finish...
  • Page 39: Sdi Analysis Features (Lv 5770Ser08 And Lv 5770Ser09A)

    2. SPECIFICATIONS 2.3.28 SDI Analysis Features (LV 5770SER08 and LV 5770SER09A) Data Dump Display HD-SDI and SD-SDI Display Format Displays data separated by serial data sequence or by channel 3G-SDI Display Format Stream 1, stream 2, stream A and B simultaneously HD Dual Link Display Format Link A, link B, link A and B simultaneously Line Select...
  • Page 40: Sdi Ancillary Data List Display (Lv 5770Ser08 And Lv 5770Ser09A)

    Reference Signal A Leader TSG that supports lip syncing Measurement Method Measures the time difference when the luminance level of the video signal exceeds the specified value and when...
  • Page 41: Sdi Closed Caption Packet Display (Lv 5770Ser08 And Lv 5770Ser09A)

    2. SPECIFICATIONS Supported Audio Signals Embedded audio signal, digital audio signal Measurement Range (Bar Display) ±50 ms, ±100 ms, ±500 ms, ±1.0 s, ±2.5 s Measurement Range (Numeric Display) ±3999 ms Measurement Resolution 1 ms Thumbnail Display Picture, audio level meter 2.3.31 SDI Closed Caption Packet Display (LV 5770SER08 and LV 5770SER09A) Table 2-7 SD-SDI video signal formats and standards...
  • Page 42: Eye Pattern Display (Lv 5770Ser09A)

    2. SPECIFICATIONS 2.3.32 Eye Pattern Display (LV 5770SER09A) Display Displays the input SDI waveform before equalizing 3G-SDI, HD-SDI, SD-SDI Displays channel A or B, whichever is selected HD Dual Link Displays link A or B, whichever is selected Method Equivalent time sampling Frequency Response 7 GHZ -3dB (converted from the rise time) Amplitude Accuracy...
  • Page 43: Jitter Display (Lv 5770Ser09A)

    2. SPECIFICATIONS 2.3.33 Jitter Display (LV 5770SER09A) Display Displays the jitter component of an SDI signal 3G-SDI, HD-SDI, SD-SDI Displays channel A or B, whichever is selected HD Dual Link Displays link A or B, whichever is selected Method Phase detection method Gain ×8, ×2, ×1 Measurement Range...
  • Page 44: Eye Pattern And Jitter Detection (Lv 5770Ser09A)

    2. SPECIFICATIONS 2.3.34 Eye Pattern and Jitter Detection (LV 5770SER09A) Error Detection On or off per item Error Threshold Settings Can be set individually for 3G-SDI, HD-SDI, and SD-SDI signals Event Log Stores eye patterns and jitter errors Threshold Values 100 % of the values in the SMPTE standard Eye-Pattern Amplitude Upper Limit...
  • Page 45: Alarm Output Feature

    2. SPECIFICATIONS 2.3.36 Alarm Output Feature Display Indication When an error occurs or the fan stops rotating, an alarm is displayed. Remote Control Connector Output Each time that an error occurs or the fan stops rotating, a signal is transmitted from the remote control connector to indicate this occurrence.
  • Page 46: Panel Description

    3. PANEL DESCRIPTION PANEL DESCRIPTION Front Panel Figure 3-1 Front panel Table 3-1 Front panel description Name Description Measures the SDI signal being applied to the LV 5770SER08 or LV 5770SER09A. CMPST Measures the composite signal or HD tri-level sync signal being applied to the LV 5770SER03A.
  • Page 47 3. PANEL DESCRIPTION Name Description F•1 to F•7 Carries out the corresponding function menu operation. See section 4.6.2, “Function Menu Operations.” 1 to 4 Select the display area. See section 5.2, “Selecting the Display Area.” V POS Adjusts the vertical position of the video signal waveform or eye pattern waveform. Press this key to return the position to the reference position.
  • Page 48: Rear Panel

    Name Description connected to this jack, the LV 5770 transmits the audio that is embedded in an SDI signal or the audio that is applied to the LV 5770SER41 or LV 5770SER43. This requires the LV 5770SER41 or LV 5770SER43.
  • Page 49 3. PANEL DESCRIPTION Name Description AC inlet Attach the included cover/inlet stopper to the AC inlet. See section 4.1, “Cover/Inlet Stopper.” Ground This is used to connect the instrument to an external ground. terminal REMOTE This is a D-sub, 15-pin remote control connector. This can be used to execute actions such as loading presets.
  • Page 50: Before You Begin Measuring

    4. BEFORE YOU BEGIN MEASURING BEFORE YOU BEGIN MEASURING Cover/Inlet Stopper A cover/inlet stopper is included with the instrument. Use this device to prevent the power cord from being pulled free of the AC inlet. 4.1.1 Attaching the Cover/Inlet Stopper Cover the power cord with the cover/inlet stopper.
  • Page 51: Turning The Instrument On And Off

    To turn on the power, press the power switch. The power switch LED lights, and the instrument turns on. When you turn on the power, the LV 5770 starts with the same panel settings that were being used when it was last turned off.
  • Page 52 See section 5.4, “Selecting the Input Channel.” • Cables It has been confirmed for each channel that errors do not occur when the LV 5770 receives an 800 mVp-p stress pattern through the following cables. LS-5CFB cable, 70 m LS-5CFB cable, 110 m L-5C2V cable, 260 m •...
  • Page 53: Sdi Signal Output (Lv 5770Ser08 And Lv 5770Ser09A)

    SDI INPUT A or SDI INPUT B. Use a commercially available HDMI cable to connect the LV 5770 to an LCD monitor. Press A or B to select the output channel. For HD dual link signals, a signal consisting of the combination of links A and B is generated.
  • Page 54: External Sync Signal Input (Lv 5770Ser03A, Lv 5770Ser08, And Lv 5770Ser09A)

    (phase difference display). (*1) Apply an external sync signal to an external sync signal input connector, and then press EXT. The LV 5770 determines the sync signal format automatically. As shown in the figure below, the external sync signal input connectors are loop-through.
  • Page 55 4. BEFORE YOU BEGIN MEASURING External sync signals that are compatible with each input signal are indicated with a check mark in the following table. Table 4-2 External sync signal formats (SD, HD, and HD dual link) Input Signal Format HD dual link NTSC with 10 field ...
  • Page 56 4. BEFORE YOU BEGIN MEASURING Table 4-3 External sync signal formats (3G) Input Signal Format 3G-A 3G-B 3G-B (2map) NTSC with 10 field        ID (59.94 Hz)(*1)      NTSC (59.94 Hz) ...
  • Page 57: Composite Signal I/O (Lv 5770Ser03A)

    4. BEFORE YOU BEGIN MEASURING 4.4.5 Composite Signal I/O (LV 5770SER03A) Figure 4-10 Composite I/O connectors • Signal Input Apply an NTSC/PAL composite signal or an HD tri-level sync signal to INPUT A or INPUT B. To switch the measurement channel, press A or B. Note that pressing the SIM key has no effect.
  • Page 58: Analog Audio Signal I/O (Lv 5770Ser42)

    4. BEFORE YOU BEGIN MEASURING Use the system settings to set the function of the audio I/O connectors to input or output. Before you apply signals, check that the function of the connectors has been set to input. Failing to do so could damage the instrument. Use the output signal for monitoring purposes.
  • Page 59: Dvi-D Output

    100 kΩ. • About the Unit LV 5770 audio signals are displayed in units of dBFS with 4 dBu scaled to -20 dBFS. A conversion table between dBu and dBFS is shown below. Table 4-5 dBu, dBFS conversion table...
  • Page 60: General Display Explanation

    4. BEFORE YOU BEGIN MEASURING General Display Explanation Figure 4-14 General display explanation Table 4-6 General display explanation Name Description Date and time The date and time are displayed here. See sections 7.2.1, “General Settings” and 7.2.4, “Setting the Date and Time.”...
  • Page 61: Panel Operation Basics

    Alarm indication This displays various alarms. If either of the following alarms is displayed, contact your local LEADER agent. FAN ALARM: This appears when there is a problem with the fan. OVER HEAT: This appears when the internal temperature has risen to an abnormal level.
  • Page 62: Function Menu Operations

    4. BEFORE YOU BEGIN MEASURING 4.6.2 Function Menu Operations This section explains how to operate the function menu, using the function menu on the vector display as an example. The function menu items correspond to F•1 to F•7. Figure 4-15 Function menu operations •...
  • Page 63: Enabling And Releasing The Key Lock

    Enabling and Releasing the Key Lock You can prevent accidental operations on the LV 5770 by enabling the key lock. The key lock disables all LV 5770 keys except for the power switch. (Remote control is still valid even if the key lock is enabled.)
  • Page 64: Operating The Shortcut Key

    See section 7.4, “Setting the Shortcut Key.” • DIRECT The panel settings that are registered to the SHORT key are loaded. To register the panel settings, configure the LV 5770 to the settings that you want to register, press MEM, and then press SHORT. • VOLUME You can adjust the headphone volume by pressing SHORT and then turning the function dial (F•D).
  • Page 65: Basic Operating Procedures

    BASIC OPERATING PROCEDURES This chapter explains the basic operating procedures of the LV 5770. We recommend that you follow these basic operations until you fully understand how the LV 5770 is designed to operate. Figure 5-1 Operating procedures Select the display format.
  • Page 66: Selecting The Display Format

    Selecting the Display Format The LV 5770 supports both a multi-screen display and a 1-screen display. Press MULTI to switch between the 1-screen display and the multi-screen display. The key's LED lights when the multi-screen display is active.
  • Page 67: Selecting The Display Area

    5. BASIC OPERATING PROCEDURES Selecting the Display Area The LV 5770 is composed of four screens. Press a key from 1 to 4 to select the area that you want to operate. When the menu is being displayed on the multi-screen display, the selected area is displayed with a blue border.
  • Page 68: Selecting The Input Channel

    Figure 5-6 Single input mode and simul mode Selecting the Display Mode The LV 5770 has six display modes: WFM (video signal waveform display), VECT (vector display), PIC (picture display), AUDIO (audio display), STATUS (status display), and EYE (eye pattern display). Press MODE on the front panel to select the display mode.
  • Page 69 5. BASIC OPERATING PROCEDURES WFM(*1) VECT(VECTOR)(*1) VECT(5BAR)(*1) AUDIO STATUS Figure 5-7 Selecting the display mode The audio meter is not displayed if an LV 5770SER41 or LV 5770SER43 is not installed in the LV 5770.
  • Page 70: Detailed Measurement Examples

    DETAILED MEASUREMENT EXAMPLES This chapter explains detailed measurement examples. For the basic operating procedures, see chapter 5, “BASIC OPERATING PROCEDURES.” Initialize the LV 5770 immediately before you perform the operating procedures shown here. See section 7.7, “Initializing Settings.” SDI Signal Measurement •...
  • Page 71: Sdi Signal Eye Pattern Measurement

    Apply an SDI signal to SDI INPUT A or SDI INPUT B on the rear panel. Turn the MULTI key off (optional). The LV 5770 switches to the 1-screen display, which is easier to view. (On the multi-screen display, one of these displays is shown.) This is not supported in simul mode or on the multi-screen display of 3G-B(2map) signals.
  • Page 72: Embedded Audio Signal Measurement

    Apply an SDI signal to SDI INPUT A or SDI INPUT B on the rear panel. Turn the MULTI key off (optional). The LV 5770 switches to the 1-screen display, which is easier to view. Press AUDIO. Press F•1 SOURCE SELECT and then F•2 1ST GRP SELECT or F•3 2ND GRP SELECT to select the measurement group.
  • Page 73: External Digital Audio Signal Measurement

    Check that the Audio BNC settings are set to INPUT on the REAR PANEL SETUP tab in the system settings. These settings are set to INPUT when the LV 5770 is initialized. See section 7.1.2, “Rear Panel Settings.”...
  • Page 74: Analog Audio Signal Measurement

    Check that the ANALOG AUDIO setting is set to INPUT on the REAR PANEL SETUP tab in the system settings. This setting is set to INPUT when the LV 5770 is initialized. See sections 4.4.7, “Analog Audio Signal I/O (LV 5770SER42)” and 7.1.2, “Rear Panel Settings.”...
  • Page 75: Embedded Audio Signal Output

    6. DETAILED MEASUREMENT EXAMPLES Embedded Audio Signal Output You can generate channels 1 to 16 of an audio signal that is embedded in an SDI signal from the rear panel DIGITAL AUDIO IN/OUT connectors. Group A generates channels 1 to 8, and group B generates channels 9 to 16.
  • Page 76: Analog Audio Signal Output

    6. DETAILED MEASUREMENT EXAMPLES Analog Audio Signal Output You can perform a D/A conversion on and generate up to eight channels of embedded audio signals or external digital audio signals as analog audio signals from the rear panel ANALOG AUDIO connector. This section will show the procedure for generating embedded audio signals.
  • Page 77: System Settings

    7. SYSTEM SETTINGS SYSTEM SETTINGS You can use the system menu to configure LV 5770 settings and optional unit settings. To display the system menu, press SYS. SYS → Figure 7-1 System menu I/O Settings To configure the I/O settings, press F•1 FORMAT IN OUT on the system menu. FORMAT IN OUT is a tab menu.
  • Page 78 “ILLEGAL FORMAT” will be displayed. Specify a correct format. It may take the LV 5770 approximately 10 seconds to switch to a different format. Table 7-1 Input format settings Link Format...
  • Page 79 7. SYSTEM SETTINGS Link Format Color System Pixel Depth Scanning Active Sample Frame Rate (*1) 3G-A YCbCr(4:2:2) 10bit 1080P 1920 60/59.94/50 12bit 1080P 1920 30/29.97/25/24/23.98 1080i 1920 30/29.97/25 1080PsF 1920 30/29.97/25/24/23.98 YCbCr(4:4:4) 10bit 1080P 1920 30/29.97/25/24/23.98 1080i 1920 30/29.97/25 1080PsF 1920 30/29.97/25/24/23.98 720P...
  • Page 80: Rear Panel Settings

    7. SYSTEM SETTINGS Link Format Color System Pixel Depth Scanning Active Sample Frame Rate (*1) 3G-B(2map) YCbCr(4:2:2) 10bit 1080P 1920 30/29.97/25/24/23.98 1080i 1920 30/29.97/25 1080PsF 1920 30/29.97/25/24/23.98 720P 1920 60/59.94/50/ 30/29.97/25/24/23.98 Note that when i/PsF Select is set to Interlace, the frame rate is displayed. For example, if the field rate is 59.94 Hz, set the frame rate to 29.97.
  • Page 81 7. SYSTEM SETTINGS ● GROUP A OUT SEL and GROUP B OUT SEL (LV 5770SER41 and LV 5770SER43) When GROUP A or GROUP B is set to OUTPUT, select the corresponding output signal. The LV 5770SER08 or LV 5770SER09A is required to generate embedded audio signals.
  • Page 82 7. SYSTEM SETTINGS ● Color Format (LV 5770SER08 and LV 5770SER09A) Select the picture monitor output format. If you select Auto, the signal is generated in the same format as the input signal. Auto / YCbCr 422 / YCbCr 444 / RGB 444 ●...
  • Page 83: Configuring The Lv 5770

    7. SYSTEM SETTINGS Configuring the LV 5770 To configure the LV 5770, press F•2 SYSTEM SETUP on the system menu. SYSTEM SETUP is a tab menu. For details on how to operate tab menus, see section 4.6.3, “Tab Menu Operations.”...
  • Page 84 7. SYSTEM SETTINGS ● Format (LV 5770SER03A, LV 5770SER08, and LV 5770SER09A) Turn the format indication (for example, 1080i/59.94 or NTSC) that is shown at the top of the screen on or off. ON / OFF ● Date Select the display format for the date that is shown in the upper left of the screen. y = the year in the Gregorian calendar, m = the month, d = the day OFF / y/m/d / m/d/y / d/m/y ●...
  • Page 85: Configuring Ethernet Settings

    Configuring Ethernet Settings Configure the Ethernet settings on the ETHERNET SETUP tab. The settings that you specify here will not be initialized even if you initialize the LV 5770. In addition, they are not registered to presets. See chapter 11, “ETHERNET REMOTE CONTROL.”...
  • Page 86 7. SYSTEM SETTINGS ● Ethernet Select Select how to set the IP address. This setting is enabled after you restart the LV 5770. DHCP: The IP address, subnet mask, and default gateway are set automatically. Set the IP address, subnet mask, and default gateway manually.
  • Page 87: Remote Control Settings

    Remote Control Settings Use the REMOTE SETUP tab to configure remote control settings. The settings that you specify here will not be initialized even if you initialize the LV 5770. In addition, they are not registered to presets. See chapter 10, “REMOTE CONTROL.”...
  • Page 88: Setting The Date And Time

    ON. To set the date and time manually, set SNTP Client Select to OFF, and then press F•1 COMPLETE. Then, press F•2 SYSTEM SETUP again. The settings that you specify here will not be initialized even if you initialize the LV 5770. In addition, they are not registered to presets.
  • Page 89: Displaying System Information

    Displaying System Information To display the system information, press F•3 SYSTEM INFO on the system menu. You can use this screen to view the LV 5770 firmware version and the types of installed optional units. SYS → F•3 SYSTEM INFO →...
  • Page 90: Configuring License Settings

    7. SYSTEM SETTINGS Configuring License Settings To configure the license settings, press F•5 LICENSE SETUP on the system menu. You can use this screen to view the MAC address and install options. For details on installing options, see the instruction manuals for the options. SYS →...
  • Page 91: Initializing Settings

    7. SYSTEM SETTINGS Initializing Settings To initialize the settings, press F•7 INITIALIZE on the system menu. To proceed with the initialization, press F•1 INIT YES. To cancel the initialization, press F•3 INIT NO. SYS → F•7 INITIALIZE → Figure 7-10 INITIALIZE menu When you initialize the settings, all the settings—excluding those listed below—are initialized.
  • Page 92: Capture Feature

    You can use the screen capture feature to capture still-image data of the screen. You can save the captured data to USB memory or overlay it on the input signal on the LV 5770 display. ● Frame Capture (LV 5770SER08 and LV 5770SER09A) You can use the frame capture feature to capture single frames of data from the SDI signal.
  • Page 93: Screen Capture

    Configure the LV 5770 so that the display that you want to capture appears on the screen. Press CAP. When you press CAP, the LV 5770 stores a screen capture of the display in its internal memory. You can also take screen captures by pressing F•2 REFRESH while the capture menu is displayed.
  • Page 94: Saving To A Usb Memory Device

    If you press CAP and perform an operation such as changing the display mode, the acquired screen capture data is deleted. However, by saving the screen capture data to a USB memory device in BSG format, you can display the screen capture data on the LV 5770 even after you restart the instrument.
  • Page 95: Displaying Screen Capture Data Saved To A Usb Memory Device

    USB memory as .bsg files, follow the procedure below. (Screen capture data that has been saved in BMP format and screen capture data that has been saved in BSG format on a different model cannot be displayed on the LV 5770.) Press CAP.
  • Page 96: Deleting Screen Capture Data Saved To A Usb Memory Device

    8. CAPTURE FEATURE 8.1.5 Deleting Screen Capture Data Saved to a USB Memory Device To delete screen capture data that has been saved to a USB memory device, follow the procedure below. (You can also use a PC to delete the data.) Press CAP.
  • Page 97: Frame Capture (Lv 5770Ser08 And Lv 5770Ser09A)

    Press F•1 TRIGGER to select MANUAL. Press F•2 REFRESH. One frame of data is captured in the LV 5770. (In simul mode, the data of both channels A and B is captured.) The captured frame data is cleared when you change the input channel or other...
  • Page 98 When the message below appears, press any key except for the power key. If an error occurs during error standby, the LV 5770 captures the frame data at that point and stops the frame capture. (In simul mode, if an error occurs on channel A or channel B, the LV 5770 captures the frame data of the channel in which the error occurred and stops the frame capture.)
  • Page 99: Displaying Frame Capture Data

    Saving to a USB Memory Device The frame data captured in the LV 5770 is cleared when the power is turned off. If you want to display it later even after the power is turned off, save the data to USB memory by following the procedure below (save the data in FRM format).
  • Page 100 F•4 FILE TYPE are set to OFF, or when there is no frame data captured in the LV 5770. When the input signal is 1080i/59.94 and all the file types that you can select with F•4 FILE TYPE are set to ON, it takes about 50 seconds to save the data.
  • Page 101: Displaying Frame Capture Data Saved To A Usb Memory Device

    Turn the function dial (F•D) to select the .frm file that you want to display. Press F•1 RECALL. To display frame data, the LV 5770 must be receiving a signal whose format is the same as that of the saved data. The FORMAT item at the bottom of the display shows the format of the saved data.
  • Page 102: Deleting Frame Capture Data Saved To A Usb Memory Device

    8. CAPTURE FEATURE 8.2.5 Deleting Frame Capture Data Saved to a USB Memory Device To delete frame capture data that has been saved to a USB memory device, follow the procedure below. (You can also use a PC to delete the data.) Press F•6 RECALL on the capture menu.
  • Page 103: Preset Feature

    • Date and time settings (DATE&TIME) Registering Presets To register a preset, follow the procedure below. Set the LV 5770 to the settings that you want to register. Press MEM. The preset registration display appears. Figure 9-1 Preset registration display...
  • Page 104 9. PRESET FEATURE Press F•1 COMMENT INPUT. The comment input display appears. You can also copy a comment from a preset that already has a comment saved to it. To copy a comment, on the preset registration display, move the cursor to the preset that has the comment that you want to copy, and press the function dial (F•D).
  • Page 105: Loading Presets

    9. PRESET FEATURE Loading Presets To load a preset, follow the procedure below. Press RCLL. The preset load menu appears. Figure 9-4 Preset load menu Press a key from F•1 NO.1 to F•6 NO.6. If the preset that you want to load is number 7 or greater, press F•7 more or turn the function dial (F•D).
  • Page 106: Copying All Presets

    Copying All Presets 9.4.1 Copying All Presets from the LV 5770 to a USB Memory Device To copy all the presets from the LV 5770 to a USB memory device, follow the procedure below. Press MEM. The preset registration display appears.
  • Page 107: Copying All Presets From A Usb Memory Device To The Lv 5770

    PRESET_00.PRE (to PRESET_59.PRE) ..Preset number 1 to number 60 9.4.2 Copying All Presets from a USB Memory Device to the LV 5770 To copy all the presets from a USB memory device to the LV 5770, follow the procedure below. Press MEM.
  • Page 108: 10. Remote Control

    10. REMOTE CONTROL 10. REMOTE CONTROL You can use the remote control connector on the rear panel to load presets, transmit alarm signals, and perform other operations. Use the supplied 15-pin D-sub connector to control the LV 5770. ● Pinout Example This section contains a diagram of the remote control connector, displayed as it appears on the rear panel, and a table that describes the connector's pinout.
  • Page 109 10. REMOTE CONTROL ● Configuring the LV 5770 To set the remote control connector, use the system settings. For details, see section 7.2.3, “Remote Control Settings.” SYS → F•2 SYSTEM SETUP → F•3 NEXT TAB → F•3 NEXT TAB →...
  • Page 110 10. REMOTE CONTROL After a setting is made, it may take about 3 seconds for the operation to finish. If you configure subsequent settings before the initial operation finishes, only the last setting will take effect. All settings in between will be discarded. (In the following example, remote control 2 will be discarded.) Figure 10-4 Remote control timing 2 ●...
  • Page 111 10. REMOTE CONTROL The control table when Remote Mode is set to BINARY is shown below. Table 10-3 Loading presets (BINARY) Preset...
  • Page 112 10. REMOTE CONTROL Preset ● Controlling the Loudness Measurement The control table when Remote Select is set to Recall and Loudness is shown below. Table 10-4 Controlling the loudness measurement 9p (/P8) 8p (/P7) Clear the loudness measurement Start the loudness measurement Stop the loudness measurement...
  • Page 113: 11. Ethernet Remote Control

    LEADER does not guarantee that this feature will work in any network environment. 11.1 TELNET From a PC connected to the same network as the LV 5770, most of the operations that you can perform from the front panel can be controlled remotely. 11.1.1 Procedure Configure the Ethernet settings on the LV 5770's ETHERNET SETUP tab.
  • Page 114: How To Enter Commands

    Examples of how to enter commands are shown below. With the factory default settings, return values are returned only for queries. If you want the LV 5770 to output return values for all commands, send a "REMOTE:REPLY" with the parameter set to ON.
  • Page 115: Telnet Commands

    11.1.3 TELNET Commands TELNET commands follow the LV 5770 or the unit menu structure. For explanations of each item, see the LV 5770 or the unit instruction manual. Depending on the current settings, some of the items that are described in this manual may be invalid.
  • Page 116 11. ETHERNET REMOTE CONTROL Command Parameter SYS:REAR:PIC_MONI_OUT:PIXEL_DEPTH AUTO / 8BIT / 10BIT / 12BIT / ? SYS:REAR:PIC_MONI_OUT:2MAPPING STREAM1 / STREAM2 / ? SYS:GENERAL:MULTI_DISPLAY 2MULTI / 4MULTI / ? SYS:GENERAL:CAPTURE_MODE SCREEN / VIDEO_FRAME / ? SYS:GENERAL:MEM_STR_MODE LOUD2H / LOUD32H / ? SYS:GENERAL:INFO:FORMAT ON / OFF / ? SYS:GENERAL:INFO:DATE...
  • Page 117 11. ETHERNET REMOTE CONTROL Command Parameter SYS:INFO:BOARD:SDI_INPUT ? (Return value: 0 (not installed) / 1 (installed)) SYS:INFO:BOARD:EYE_PATTERN ? (Return value: 0 (not installed) / 1 (installed)) SYS:INFO:BOARD:COMPOSITE_VIDEO ? (Return value: 0 (not installed) / 1 (installed)) SYS:INFO:BOARD:AUDIO_DIGITAL_41 ? (Return value: 0 (not installed) / 1 (installed)) SYS:INFO:BOARD:AUDIO_ANALOG ? (Return value: 0 (not installed) / 1 (installed)) SYS:INFO:BOARD:AUDIO_DIGITAL_43...
  • Page 118 11. ETHERNET REMOTE CONTROL Command Parameter WFM:FILTER:NORMAL FLAT / LOWPASS / ? WFM:FILTER:COMPOSITE FLAT / LUM / FLAT_LUM / LUM_CRMA / ? WFM:SWEEP:SWEEP H / V / ? WFM:SWEEP:H_SWEEP 1H / 2H / ? WFM:SWEEP:V_SWEEP 1V / 2V / ? WFM:SWEEP:H_MAG X1 / X10 / X20 / ACTIVE / BLANK / ? WFM:SWEEP:V_MAG...
  • Page 119 11. ETHERNET REMOTE CONTROL Command Parameter VECTOR:LINE_SELECT ON / ACH / BCH / BOTH / 2MAP_S1 / 2MAP_S2 / OFF / CINELITE / ? VECTOR:LINE_SELECT:FIELD FIELD1 / FIELD2 / FRAME / ? VECTOR:LINE_NUMBER 1 to 1125 / ? VECTOR:MARKER ON / OFF / ? VECTOR:MODE VECTOR / 5BAR / ? VECTOR:5BAR:SCALE...
  • Page 120 11. ETHERNET REMOTE CONTROL Command Parameter PICTURE:BRIGHTNESS -50.0 to 50.0 / ? PICTURE:CONTRAST 0.0 to 200.0 / ? PICTURE:GAIN:R 0.0 to 200.0 / ? PICTURE:GAIN:G 0.0 to 200.0 / ? PICTURE:GAIN:B 0.0 to 200.0 / ? PICTURE:GAIN:CHROMA 0.0 to 200.0 / ? PICTURE:BIAS:R -50.0 to 50.0 / ? PICTURE:BIAS:G...
  • Page 121 11. ETHERNET REMOTE CONTROL Command Parameter PICTURE:DISPLAY:THUMBNAIL:WFM ON / OFF / ? PICTURE:DISPLAY:THUMBNAIL:HISTO ON / OFF / ? PICTURE:DISPLAY:THUMBNAIL:HISTO:FORM LUMA / ALIGN / MIX / ? PICTURE:DISPLAY:THUMBNAIL:HISTO:Y ON / OFF / ? PICTURE:DISPLAY:THUMBNAIL:HISTO:R ON / OFF / ? PICTURE:DISPLAY:THUMBNAIL:HISTO:G ON / OFF / ? PICTURE:DISPLAY:THUMBNAIL:HISTO:B ON / OFF / ? PICTURE:DISPLAY:SD...
  • Page 122 11. ETHERNET REMOTE CONTROL Command Parameter STATUS:EXT_REF:TOTAL:DATA ? (Return value: TOTAL PHASE) STATUS:AV_PHASE None STATUS:AV_PHASE:SCALE 50 / 100 / 500 / 1000 / 2500 / ? STATUS:AV_PHASE:CH1:DATA ? (Return value: data / MISSING / UNLOCK / NO_SIGNAL / -) STATUS:AV_PHASE:CH2:DATA ? (Return value: data / MISSING / UNLOCK / NO_SIGNAL / -) STATUS:AV_PHASE:CH3:DATA...
  • Page 123 11. ETHERNET REMOTE CONTROL Command Parameter STATUS:ANC_PACKET:DATA_BROADCAST:DATA ? (Return value: DETECT / MISSING / -) STATUS:ANC_PACKET:VBI:DATA ? (Return value: DETECT / MISSING / -) STATUS:ANC_PACKET:AFD:DATA ? (Return value: DETECT / MISSING / -) STATUS:ANC_PACKET:JPN_CC1:DATA ? (Return value: DETECT / MISSING / -) STATUS:ANC_PACKET:JPN_CC2:DATA ? (Return value: DETECT / MISSING / -) STATUS:ANC_PACKET:JPN_CC3:DATA...
  • Page 124 11. ETHERNET REMOTE CONTROL Command Parameter STATUS:ANC:PKT:ARIB:NETQ:BIT:Q25 ON / OFF / ? STATUS:ANC:PKT:ARIB:NETQ:BIT:Q26 ON / OFF / ? STATUS:ANC:PKT:ARIB:NETQ:BIT:Q27 ON / OFF / ? STATUS:ANC:PKT:ARIB:NETQ:BIT:Q28 ON / OFF / ? STATUS:ANC:PKT:ARIB:NETQ:BIT:Q29 ON / OFF / ? STATUS:ANC:PKT:ARIB:NETQ:BIT:Q30 ON / OFF / ? STATUS:ANC:PKT:ARIB:NETQ:BIT:Q31 ON / OFF / ? STATUS:ANC:PKT:ARIB:NETQ:BIT:Q32...
  • Page 125 11. ETHERNET REMOTE CONTROL Command Parameter STATUS:ERROR:AUDIO:BCH ON / OFF / ? STATUS:ERROR:AUDIO:DBN ON / OFF / ? STATUS:ERROR:AUDIO:PARITY ON / OFF / ? STATUS:ERROR:AUDIO:INHIBIT ON / OFF / ? STATUS:ERROR:AUDIO:SAMPLE ON / OFF / ? STATUS:ERROR:GAMUT:LPF HD1M_SD1M / HD2.8M_SD1M / OFF / ? STATUS:ERROR:GAMUT ON / OFF / ? STATUS:ERROR:GAMUT:UPPER...
  • Page 126 11. ETHERNET REMOTE CONTROL Command Parameter STATUS:ERROR:SDI:CABLE_WAR_SD 50 to 300 / ? None EYE:MODE EYE / JITTER / ? EYE:INTEN:EYE -128 to 127 / ? EYE:INTEN:SCALE -8 to 7 / ? EYE:COLOR:EYE WHITE / YELLOW / CYAN / GREEN / MAGENTA / RED / BLUE / ? EYE:COLOR:SCALE WHITE / YELLOW / CYAN / GREEN / MAGENTA / RED /...
  • Page 127 11. ETHERNET REMOTE CONTROL Command Parameter EYE:ERROR:3G:OVERSHOOT_FALL:MAX 0 to 200 / ? EYE:ERROR:HD:AMPLITUDE ON / OFF / ? EYE:ERROR:HD:AMPLITUDE:UPPER 80 to 140 / ? EYE:ERROR:HD:AMPLITUDE:LOWER 40 to 100 / ? EYE:ERROR:HD:RISETIME ON / OFF / ? EYE:ERROR:HD:RISETIME:MAX 40 to 140 / ? EYE:ERROR:HD:FALLTIME ON / OFF / ? EYE:ERROR:HD:FALLTIME:MAX...
  • Page 128 11. ETHERNET REMOTE CONTROL Table 11-4 LV 5770SER03A commands Command Parameter None WFM:INTEN:WFM -128 to 127 / ? WFM:COLOR WHITE / YELLOW / CYAN / GREEN / MAGENTA / RED / BLUE / MULTI / ? WFM:INTEN:SCALE -8 to 7 / ? WFM:SCALE:COLOR WHITE / YELLOW / CYAN / GREEN / MAGENTA / RED / BLUE / ?
  • Page 129 11. ETHERNET REMOTE CONTROL Command Parameter VECTOR:DISPLAY:SCH:DATA ? (Return value: SCH) VECTOR:DISPLAY:THUMBNAIL:AUDIO ON / OFF / ? VECTOR:DISPLAY:THUMBNAIL:PICTURE ON / OFF / ? VECTOR:DISPLAY:THUMBNAIL:HISTO ON / OFF / ? VECTOR:DISPLAY:THUMBNAIL:HISTO:FORM LUMA / ALIGN / MIX / ? VECTOR:DISPLAY:THUMBNAIL:HISTO:Y ON / OFF / ? VECTOR:DISPLAY:THUMBNAIL:HISTO:R ON / OFF / ? VECTOR:DISPLAY:THUMBNAIL:HISTO:G...
  • Page 130 11. ETHERNET REMOTE CONTROL Command Parameter PICTURE:DISPLAY:THUMBNAIL:HISTO:Y ON / OFF / ? PICTURE:DISPLAY:THUMBNAIL:HISTO:R ON / OFF / ? PICTURE:DISPLAY:THUMBNAIL:HISTO:G ON / OFF / ? PICTURE:DISPLAY:THUMBNAIL:HISTO:B ON / OFF / ? STATUS None STATUS:EXT_REF None STATUS:EXT_REF:USER_REF None STATUS:EXT_REF:DEFAULT None STATUS:EXT_REF:REF:DATA ? (Return value: USER_REF / DEFAULT) STATUS:EXT_REF:STAT:DATA ? (Return value: INT / HD / BB / NO_SIGNAL) STATUS:EXT_REF:H_TIME:DATA...
  • Page 131 11. ETHERNET REMOTE CONTROL Command Parameter CH9 / CH10 / CH11 / CH12 / CH13 / CH14 / CH15 / CH16 / LT / ? AUDIO:LISSAJOU:MAP:SINGLE_16_R CH1 / CH2 / CH3 / CH4 / CH5 / CH6 / CH7 / CH8 / CH9 / CH10 / CH11 / CH12 / CH13 / CH14 / CH15 / CH16 / RT / ? AUDIO:LISSAJOU:MAP:SINGLE_MIX_L...
  • Page 132 11. ETHERNET REMOTE CONTROL Command Parameter CH9 / CH10 / CH11 / CH12 / CH13 / CH14 / CH15 / CH16 / ? AUDIO:LISSAJOU:MAP:MULTI16_R3 CH1 / CH2 / CH3 / CH4 / CH5 / CH6 / CH7 / CH8 / CH9 / CH10 / CH11 / CH12 / CH13 / CH14 / CH15 / CH16 / ? AUDIO:LISSAJOU:MAP:MULTI16_L4...
  • Page 133 11. ETHERNET REMOTE CONTROL Command Parameter AUDIO:SURROUND:5.1 NORMAL / PHANTOM / ? AUDIO:SURROUND:AUTO_GAIN ON / OFF / ? AUDIO:SURROUND:MAP:L CH1 / CH2 / CH3 / CH4 / CH5 / CH6 / CH7 / CH8 / CH9 / CH10 / CH11 / CH12 / CH13 / CH14 / CH15 / CH16 / ? AUDIO:SURROUND:MAP:R CH1 / CH2 / CH3 / CH4 / CH5 / CH6 / CH7 / CH8 /...
  • Page 134 11. ETHERNET REMOTE CONTROL Command Parameter / B12 / B13 / B14 / B15 / B16 / ? AUDIO:STATUS:USER_BIT:ALIGN LSB / MSB / ? AUDIO:STATUS:ERROR:LEVEL_OVER ON / OFF / ? AUDIO:STATUS:ERROR:CLIP ON / OFF / ? AUDIO:STATUS:ERROR:CLIP:DURATION 1 to 100 / ? AUDIO:STATUS:ERROR:MUTE ON / OFF / ? AUDIO:STATUS:ERROR:MUTE:DURATION...
  • Page 135 11. ETHERNET REMOTE CONTROL Command Parameter AUDIO:LOUD:INTEG:LFE_GAIN ON / OFF / ? AUDIO:LOUD:INTEG:LFE_GAIN:VALUE 0 to 10 / ? AUDIO:LOUD:SHORT:AVRG_TIME 200 to 10000 / ? (100 ms steps) AUDIO:LOUD:MOMENT:AVRG_TIME 200 to 10000 / ? (100 ms steps) AUDIO:LOUD:RESPONSE SHORTTERM / MOMENTARY / ? AUDIO:LOUD:CHART INTEGRATED / SHORTTERM / MOMENTARY / ? AUDIO:LOUD:AUTO:TRIGGER...
  • Page 136 11. ETHERNET REMOTE CONTROL Command Parameter / CH16 / NC / ? AUDIO:LOUD:MAP:CUSTOM:R CH1 / CH2 / CH3 / CH4 / CH5 / CH6 / CH7 / CH8 / CH9 / CH10 / CH11 / CH12 / CH13 / CH14 / CH15 / CH16 / NC / ? AUDIO:LOUD:MAP:CUSTOM:C CH1 / CH2 / CH3 / CH4 / CH5 / CH6 / CH7 / CH8 /...
  • Page 137 11. ETHERNET REMOTE CONTROL Command Parameter AUDIO:DOLBY:E_META_PRM PRM1 / PRM2 / PRM3 / PRM4 / PRM5 / PRM6 / PRM7 / PRM8 / ? AUDIO:DOLBY:EBI_META_PRM PRM1 / PRM2 / PRM3 / PRM4 / PRM5 / PRM6 / PRM7 / PRM8 / ? AUDIO:DOLBY:D_LISTENING FULL / EX / 3STEREO / PHANTOM / STEREO / MONO / ?
  • Page 138: Ftp

    11. ETHERNET REMOTE CONTROL 11.2 The files that are generated by the LV 5770 can be transferred to a PC connected to the same network. 11.2.1 Procedure Configure the Ethernet settings on the LV 5770's ETHERNET SETUP tab. Set the IP Address, and set FTP Server Select to ON.
  • Page 139: How To Enter Commands

    11. ETHERNET REMOTE CONTROL Type the user name and password. The user name and password are "LV5770". Use uppercase for all characters. When the user name and password are entered correctly, "ftp>" appears. Connected to ***.***.***.***. 220 FTP Server ready User (***.***.***.***:(none)): LV5770 ..
  • Page 140: Ftp Commands

    11. ETHERNET REMOTE CONTROL 11.2.3 FTP Commands Table 11-7 FTP commands Command Parameter 1 Parameter 2 LOG.TXT Storage location on the PC and file name (example: D:¥LOG.TXT) DUMP.TXT Storage location on the PC and file name (example: D:¥DUMP.TXT) CAPTURE.BMP Storage location on the PC and file name (example: D:¥CAPTURE.BMP) CAP_***.FRM Storage location on the PC and file name...
  • Page 141: Snmp

    11. ETHERNET REMOTE CONTROL 11.3 SNMP By using SNMP (Simple Network Management Protocol), you can control an LV 5770 from SNMP managers. Additionally, you can notify the SNMP managers of errors that the LV 5770 generates. The LV 5770 supports SNMPv1. 11.3.1...
  • Page 142 [Enable (3) or disable (2) TRAP transmission destination 1] 1.3.6.1.4.1.leader(20111).lv5770(21).lv5770ST1(1).l21trapTBL(9).l21trapIpTBL(2).l21tr apIp3TBL(3).l21trapManagerIp3Act(2).0 [Enable (4) or disable (2) TRAP transmission destination 1] 1.3.6.1.4.1.leader(20111).lv5770(21).lv5770ST1(1).l21trapTBL(9).l21trapIpTBL(2).l21tr apIp4TBL(4).l21trapManagerIp4Act(2).0 Restart the LV 5770. 10. When the LV 7800 starts, it transmits the standard TRAP "coldStart(0)." Check that this is received by the SNMP managers.
  • Page 143: Standard Mib

    11. ETHERNET REMOTE CONTROL 11.3.3 Standard MIB The LV 5770 uses the following standard MIBs: • RFC1213 (MIB-II) • RFC1354 (IP Forwarding Table MIB) In the tables, "ACCESS" and "SUPPORT" indicate the following: Indication Description ACCESS Information that can be read from the SNMP managers.
  • Page 144 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS SUPPORT ifInUnknownProtos ifEntry.15 Counter ○ ifOutOctets ifEntry.16 Counter ○ ifOutUcastPkts ifEntry.17 Counter ○ ifOutNUcastPkts ifEntry.18 Counter ○ ifOutDiscards ifEntry.19 Counter ○ ifOutErrors ifEntry.20 Counter ○ ifOutQLen ifEntry.21 Gauge ○ ifSpecific ifEntry.22 ObjectID ○ Table 11-10 ip group SYNTAX ACCESS SUPPORT...
  • Page 145 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS SUPPORT ipForwardNumber ipForward .1 Gauge ○ ipForwardTable ipForward .2 Aggregate ○ ipForwardDest ipForwardTable.1 IpAddress ○ ipForwardMask ipForwardTable.1 IpAddress ○ ipForwardPolicy ipForwardTable.1 INTEGER × ipForwardNextHop ipForwardTable.1 IpAddress ○ ipForwardIfIndex ipForwardTable.1 INTEGER ○ ipForwardType ipForwardTable.1 INTEGER ×...
  • Page 146 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS SUPPORT icmpOutAddrMaskReps icmp.26 Counter ○ Table 11-12 tcp group SYNTAX ACCESS SUPPORT tcpRtoAlgorithm tcp.1 INTEGER ○ tcpRtoMin tcp.2 INTEGER ○ tcpRtoMax tcp.3 INTEGER ○ tcpMaxConn tcp.4 INTEGER ○ tcpActiveOpens tcp.5 Counter ○ tcpPassiveOpens tcp.6 Counter ○...
  • Page 147 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS SUPPORT snmpInASNParseErrs snmp.6 Counter ○ snmpInTooBigs snmp.8 Counter ○ snmpInNoSuchNames snmp.9 Counter ○ snmpInBadValues snmp.10 Counter ○ snmpInReadOnlys snmp.11 Counter ○ snmpInGenErrs snmp.12 Counter ○ snmpInTotalReqVars snmp.13 Counter ○ snmpInTotalSetVars snmp.14 Counter ○ snmpInGetRequests snmp.15 Counter ○...
  • Page 148: Enterprise Mib

    11. ETHERNET REMOTE CONTROL 11.3.4 Enterprise MIB ● Enterprise Number The Enterprise Number of LEADER ELECTRONICS CORP. is 20111. iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).leader(20111) ● Enterprise MIB File Download the enterprise MIB file using FTP. The file name is "lv5770.my." (Example: GET LV5770.MY D:¥LV5770.MY) ●...
  • Page 149 11. ETHERNET REMOTE CONTROL Table 11-15 l21basicTBL(1) group SYNTAX ACCESS VALUE/RANGE l21basInputTBL l21basicTBL.1 Aggregate l21basInputUnit l21basInputTBL.1 INTEGER 1 = Sdi 2 = Analog Composite l21basInputCh l21basInputTBL.2 INTEGER 1 = A 2 = B 3 = AB l21basInputSimul l21basInputTBL.3 INTEGER 1 = Off 2 = On l21basInputStream l21basInputTBL.4...
  • Page 150 11. ETHERNET REMOTE CONTROL Table 11-16 l21systemTBL(2) group SYNTAX ACCESS VALUE/RANGE l21sysFormatTBL l21systemTBL.1 Aggregate l21sysFormatManualSelect l21sysFormatTBL.1 INTEGER 1 = Auto 2 = Manual l21sysFormatIPSF l21sysFormatTBL.2 INTEGER 1 = Interlace 2 = Segmented Frame l21sysFormatLinkFormat l21sysFormatTBL.3 INTEGER 1 = HD 2 = SD 3 = HD-Dual 4 = 3G-A 5 = 3G-B...
  • Page 151 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = SDI 9-16 l21sysRearAnalogAudio l21sysRearTBL.6 INTEGER 1 = Input 2 = Output l21sysRearDvi_IAspect l21sysRearTBL.7 INTEGER 1 = 4:3 2 = 16:9 3 = 16:10 l21sysRearPicMoniOutColor l21sysRearTBL.8 INTEGER 1 = Auto 2 = YCbCr-422 3 = YCbCr-444 4 = RGB-444 l21sysRearPicMoniOutPixelDepth...
  • Page 152 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = Loudness 32Hour l21sysEthernetTBL l21systemTBL.4 Aggregate l21sysEthernetSelect l21sysEthernetTBL.1 INTEGER 1 = DHCP 2 = IP l21sysEthernetAddress l21sysEthernetTBL.2 DisplayString IP Address l21sysEthernetSubnet l21sysEthernetTBL.3 DisplayString Subnet Mask l21sysEthernetGateway l21sysEthernetTBL.4 DisplayString Default Gateway l21sysEthernetSntpSelect l21sysEthernetTBL.5 INTEGER 1 = Off 2 = On...
  • Page 153 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE l21sysOtherDateTimeSet l21sysOtherTBL.7 INTEGER R/WO 1 = Date & Time Set l21sysOtherDateTime l21sysOtherTBL.8 DisplayString Date & Time l21sysOtherInfoFirmware l21sysOtherTBL.9 DisplayString Firmware Version l21sysOtherInfoBoardSdi l21sysOtherTBL.10 INTEGER 1 = Not installed 2 = Installed l21sysOtherInfoBoardEye l21sysOtherTBL.11 INTEGER 1 = Not installed 2 = Installed...
  • Page 154 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 5 = Magenta 6 = Red 7 = Blue 8 = Multi l21wfmColor2MapS1 l21wfmIntenTBL.3 INTEGER 1 = White 2 = Yellow 3 = Cyan 4 = Green 5 = Magenta 6 = Red 7 = Blue 8 = Multi l21wfmColor2MapS2...
  • Page 155 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = Lowpass l21wfmFilterComposite l21wfmFilterTBL.2 INTEGER 1 = Flat 2 = Lum 2 = Flat-Lum 3 = Lum-Chroma l21wfmSweepTBL l21wfmTBL.6 Aggregate l21wfmSweepSweep l21wfmSweepTBL.1 INTEGER 1 = H 2 = V l21wfmSweepHSweep l21wfmSweepTBL.2 INTEGER 1 = 1H 2 = 2H l21wfmSweepVSweep...
  • Page 156 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = Stream2 3 = Mix 4 = Align l21wfmDisplayThumbnailAudio l21wfmDisplayTBL.3 INTEGER 1 = Off 2 = On l21wfmDisplayThumbnailPicture l21wfmDisplayTBL.4 INTEGER 1 = Off 2 = On l21wfmDisplayThumbHisto l21wfmDisplayTBL.5 INTEGER 1 = Off 2 = On l21wfmDisplayThumbHistoForm l21wfmDisplayTBL.6...
  • Page 157 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 7 = Blue l21vecColor2MapS1 l21vecIntenTBL.3 INTEGER 1 = White 2 = Yellow 3 = Cyan 4 = Green 5 = Magenta 6 = Red 7 = Blue l21vecColor2MapS2 l21vecIntenTBL.4 INTEGER 1 = White 2 = Yellow 3 = Cyan 4 = Green...
  • Page 158 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = Field2 INTEGER 3 = Frame l21vecLineNumber l21vecLineSelTBL.3 INTEGER 1 to 1125 l21vecMode l21vectorTBL.5 INTEGER 1 = Vector 2 = 5Bar l21vec5BarTBL l21vectorTBL.6 Aggregate l21vec5BarScale l21vec5BarTBL.1 INTEGER 1 = % 2 = mV l21vec5BarSeaquence l21vec5BarTBL.2 INTEGER...
  • Page 159 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE l21vecMatrix l21vecMatixTBL.1 INTEGER 1 = Component 2 = Composite l21vecMatrixCompositeFormat l21vecMatixTBL.2 INTEGER 1 = Auto 2 = NTSC 3 = PAL l21vecMatrixCompositeSetup l21vecMatixTBL.3 INTEGER 1 = 0% 2 = 7.5% l21vecMatrixColorbar l21vecMatixTBL.4 INTEGER 1 = 100% 2 = 75% l21vecAnalogTBL...
  • Page 160 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = 14:9 3 = 13:9 4 = 16:9 5 = 4:3 6 = 2.39:1 7 = AFD l21picMarkerAspectShadow l21picMarkerTBL.4 INTEGER 0 to 100 l21picMarkerSafetyAction l21picMarkerTBL.5 INTEGER 1 = ARIB 2 = SMPTE 3 = User1 4 = Off l21picMarkerSafetyTitle...
  • Page 161 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE l21picCineliteFstop18pRefset l21picCineliteTBL.7 INTEGER R/WO 1 = Set l21picCineliteFstopGammaSel l21picCineliteTBL.8 INTEGER 1 = 0.45 2 = User1 3 = User2 4 = User3 5 = User-A 6 = User-B 7 = User-C 8 = User-D 9 = User-E l21picCinelitePercentUnit l21picCineliteTBL.9...
  • Page 162 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = On l21picDisplayThumbHistoForm l21picDisplayTBL.9 INTEGER 1 = Luma 2 = Align 3 = Mix l21picDisplayThumbHistoMixY l21picDisplayTBL.10 INTEGER 1 = Off 2 = On l21picDisplayThumbHistoMixR l21picDisplayTBL.11 INTEGER 1 = Off 2 = On l21picDisplayThumbHistoMixG l21picDisplayTBL.12 INTEGER...
  • Page 163 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = Stop l21staDumpTBL l21statusTBL.4 Aggregate l21staDump l21staDumpTBL.1 INTEGER R/WO 1 = Dump Display l21staDumpMode l21staDumpTBL.2 INTEGER 1 = Run 2 = Hold l21staDumpDisplay l21staDumpTBL.3 INTEGER 1 = Serial 2 = Component 3 = Binary 4 = Link-A 5 = Link-B 6 = Link-AB...
  • Page 164 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE l21staAvPhase l21staAvPhaseTBL.1 INTEGER R/WO 1 = AV Phase Display l21staAvPhaseScale l21staAvPhaseTBL.2 INTEGER 1 = 50ms 2 = 100ms 3 = 500ms 4 = 1000ms 5 = 2500ms l21staAvPhaseCh1Data l21staAvPhaseTBL.3 DisplayString Ch1 Data l21staAvPhaseCh2Data l21staAvPhaseTBL.4 DisplayString Ch2 Data...
  • Page 165 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE l21staAncpacketPayload2Data l21staAncpacketTBL.7 INTEGER 1 = Detect 2 = Missing 3 = Unmeasurable l21staAncpacketEia708_708Data l21staAncpacketTBL.8 INTEGER 1 = Detect 2 = Missing 3 = Unmeasurable l21staAncpacketEia708_608Data l21staAncpacketTBL.9 INTEGER 1 = Detect 2 = Missing 3 = Unmeasurable l21staAncpacketEia608Data l21staAncpacketTBL.10...
  • Page 166 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE l21staAncPktPayloadId l21staAncPktTBL.1 INTEGER R/WO 1 = ANC Payload ID Display l21staAncPktPayloadIdStream l21staAncPktTBL.2 INTEGER 1 = Stream1 2 = Stream2 l21staAncPktPayloadIdLink l21staAncPktTBL.3 INTEGER 1 = Link-A 2 = Link-B l21staAncPktPayloadIdData l21staAncPktTBL.4 DisplayString Payload ID l21staAncPktAudioCtrl l21staAncPktTBL.5 INTEGER...
  • Page 167 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE l21staAncPktAribNetqBitQ14 l21staAncPktTBL.24 INTEGER 1 = On 2 = Off l21staAncPktAribNetqBitQ15 l21staAncPktTBL.25 INTEGER 1 = On 2 = Off l21staAncPktAribNetqBitQ16 l21staAncPktTBL.26 INTEGER 1 = On 2 = Off l21staAncPktAribNetqBitQ17 l21staAncPktTBL.27 INTEGER 1 = On 2 = Off l21staAncPktAribNetqBitQ18 l21staAncPktTBL.28...
  • Page 168 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = Off l21staAncPktAribNetqBitS5 l21staAncPktTBL.47 INTEGER 1 = On 2 = Off l21staAncPktAribNetqBitS6 l21staAncPktTBL.48 INTEGER 1 = On 2 = Off l21staAncPktAribNetqBitS7 l21staAncPktTBL.49 INTEGER 1 = On 2 = Off l21staAncPktAribNetqBitS8 l21staAncPktTBL.50 INTEGER 1 = On 2 = Off l21staAncPktAribNetqBitS9...
  • Page 169 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = Off l21staErrorSdiHdCrc l21staErrorSdiTBL.4 INTEGER 1 = On 2 = Off l21staErrorSdiSdEdh l21staErrorSdiTBL.5 INTEGER 1 = On 2 = Off l21staErrorSdiIllegalCode l21staErrorSdiTBL.6 INTEGER 1 = On 2 = Off l21staErrorAncTBL l21statusTBL.10 Aggregate l21staErrorAncParity l21staErrorAncTBL.1 INTEGER...
  • Page 170 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = Off l21staErrorFreezeUpper l21staErrorFreezeTBL.2 INTEGER 0 to 100 l21staErrorFreezeLower l21staErrorFreezeTBL.3 INTEGER 0 to 100 l21staErrorFreezeLeft l21staErrorFreezeTBL.4 INTEGER 0 to 100 l21staErrorFreezeRight l21staErrorFreezeTBL.5 INTEGER 0 to 100 l21staErrorFreezeDuration l21staErrorFreezeTBL.6 INTEGER 2 to 300 l21staErrorBlackTBL l21statusTBL.14 Aggregate...
  • Page 171 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 3 = Cyan 4 = Green 5 = Magenta 6 = Red 7 = Blue l21eyeColorScale l21eyeColorTBL.2 INTEGER 1 = White 2 = Yellow 3 = Cyan 4 = Green 5 = Magenta 6 = Red 7 = Blue l21eyeGainTBL...
  • Page 172 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 6 = Red 7 = Blue l21eyeJitterGain l21eyeJitterTBL.3 INTEGER 1 = X1 2 = X2 3 = X8 l21eyeJitterSweep l21eyeJitterTBL.4 INTEGER 1 = 1H 2 = 2H 3 = 1V 4 = 2V l21eyeJitterFilter l21eyeJitterTBL.5 INTEGER...
  • Page 173 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = Off l21eyeError3GOverShootFallMax l21eyeError3GTBL.17 INTEGER 0 to 200 l21eyeErrorHdTBL l21eyeErrorTBL.2 Aggregate l21eyeErrorHdAmp l21eyeErrorHdTBL.1 INTEGER 1 = On 2 = Off l21eyeErrorHdAmpUpper l21eyeErrorHdTBL.2 INTEGER 80 to 140 l21eyeErrorHdAmpLower l21eyeErrorHdTBL.3 INTEGER 40 to 100 l21eyeErrorHdRise l21eyeErrorHdTBL.4 INTEGER...
  • Page 174 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE l21eyeErrorSdCurrentJit l21eyeErrorSdTBL.12 INTEGER 1 = On 2 = Off l21eyeErrorSdCurrentJitMax l21eyeErrorSdTBL.13 INTEGER 10 to 200 l21eyeErrorSdOverShootRise l21eyeErrorSdTBL.14 INTEGER 1 = On 2 = Off l21eyeErrorSdOverShootRiseMax l21eyeErrorSdTBL.15 INTEGER 0 to 200 l21eyeErrorSdOverShootFall l21eyeErrorSdTBL.16 INTEGER 1 = On 2 = Off l21eyeErrorSdOverShootFallMax...
  • Page 175 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 3 = VU l21audMeterResponsePPM l21audMeterTBL.3 INTEGER 1 = PPM1 2 = PPM2 l21audMeterResponseVU l21audMeterTBL.4 INTEGER 1 = TRUE 2 = PPM1 3 = PPM2 l21audMetePeakHold l21audMeterTBL.5 INTEGER 1 = 0.5Sec. 2 = 1Sec. 3 = 1.5Sec.
  • Page 176 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE (omitted) 16 = Ch16 l21audlissajouMapMultiR2 l21audLissajouMapTBL.6 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audlissajouMapMultiL3 l21audLissajouMapTBL.7 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audlissajouMapMultiR3 l21audLissajouMapTBL.8 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audlissajouMapMultiL4 l21audLissajouMapTBL.9 INTEGER...
  • Page 177 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE (omitted) 16 = Ch16 l21audlissajouMapMulti16R2 l21audLissajouMapTBL.18 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audlissajouMapMulti16L3 l21audLissajouMapTBL.19 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audlissajouMapMulti16R3 l21audLissajouMapTBL.20 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audlissajouMapMulti16L4 l21audLissajouMapTBL.21 INTEGER...
  • Page 178 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 8 = D8 l21audlissajouMapMultiD_MixL6 l21audLissajouMapTBL.33 INTEGER 1 = D1 (omitted) 8 = D8 l21audlissajouMapMultiD_MixR6 l21audLissajouMapTBL.34 INTEGER 1 = D1 (omitted) 8 = D8 l21audlissajouMapMultiD_MixL7 l21audLissajouMapTBL.35 INTEGER 1 = D1 (omitted) 8 = D8 l21audlissajouMapMultiD_MixR7 l21audLissajouMapTBL.36 INTEGER...
  • Page 179 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE l21audSurroundMapLl l21audSurroundMapTBL.7 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audSurroundMapRr l21audSurroundMapTBL.8 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audStatusTBL l21audioTBL.6 Aggregate l21audStatusLog l21audStatusTBL.1 INTEGER R/WO 1 = Log Display l21audStatusLogLog l21audStatusTBL.2 INTEGER 1 = Start 2 = Stop...
  • Page 180 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 32 = B16 l21audStatusChStatusAlign l21audStatusTBL.7 INTEGER 1 = LSB 1st 2 = MSB 1st l21audStatusDisplayUserBit l21audStatusTBL.8 INTEGER R/WO User Bit Display l21audStatusUserBit l21audStatusTBL.9 INTEGER 1 = Ch1 / A1 2 = Ch2 / A2 3 = Ch3 / A3 4 = Ch4 / A4 5 = Ch5 / A5...
  • Page 181 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE l21audStatusErrorMuteDuration l21audStatusTBL.15 INTEGER 1 to 5000 l21audStatusErrorParity l21audStatusTBL.16 INTEGER 1 = On 2 = Off l21audStatusErrorVaridity l21audStatusTBL.17 INTEGER 1 = On 2 = Off l21audStatusErrorCrc l21audStatusTBL.18 INTEGER 1 = On 2 = Off l21audStatusErrorCode l21audStatusTBL.19 INTEGER...
  • Page 182 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = Stop l21audLoudMag l21audLoudnessTBL.4 INTEGER 1 = Off 2 = On l21audLoudIntegMode l21audLoudnessTBL.5 INTEGER 1 = BS1770-2 2 = ARIB 3 = EBU 4 = ATSC l21audLoudIntegLevel l21audLoudnessTBL.6 DisplayString Target Level l21audLoudIntegBlkSize l21audLoudnessTBL.7 DisplayString Block Size...
  • Page 183 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE (omitted) 16 = Ch16 l21audLoudMap51C l21audLoudnessTBL.29 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audLoudMap51LFE l21audLoudnessTBL.30 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audLoudMap51LS l21audLoudnessTBL.31 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audLoudMap51RS l21audLoudnessTBL.32 INTEGER...
  • Page 184 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 2 = Mono 3 = Stereo l21audLoudMapSUbMonoLR l21audLoudnessTBL.46 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audLoudMapSubStereoL l21audLoudnessTBL.47 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audLoudMapSubStereoR l21audLoudnessTBL.48 INTEGER 1 = Ch1 (omitted) 16 = Ch16 l21audLoudPeakholdDataL l21audLoudnessTBL.49...
  • Page 185 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE l21audDolbyE_MetaPRM l21audDolbyTBL.5 INTEGER 1 = PRM1 2 = PRM2 3 = PRM3 4 = PRM4 5 = PRM5 6 = PRM6 7 = PRM7 8 = PRM8 l21audDolbyEBI_MetaPRM l21audDolbyTBL.6 INTEGER 1 = PRM1 2 = PRM2 3 = PRM3 4 = PRM4...
  • Page 186 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 17 = Lt / B1 18 = B2 19 = B3 20 = B4 21 = B5 22 = B6 23 = B7 24 = B8 25 = B9 26 = B10 27 = B11 28 = B12 29 = B13 30 = B14...
  • Page 187 11. ETHERNET REMOTE CONTROL SYNTAX ACCESS VALUE/RANGE 30 = B14 31 = B15 32 = B16 l21audPhonesDolbyDauxCh l21audPhonesTBL.4 INTEGER 1 = LtRt 2 = LoRo 3 = Mono 4 = Mute l21audPhonesDolbyDauxDRC l21audPhonesTBL.5 INTEGER 1 = Line 2 = Rf l21audSelectTBL l21audioTBL.10 Aggregate...
  • Page 188: Extended Trap (Variable Binding List)

    11. ETHERNET REMOTE CONTROL 11.3.5 Extended TRAP (Variable Binding List) ● index 1 OID: leader(20111).lv5770(21).lv5770ST1(1).trapTBL(9).trapStrTBL(1).1.0 Syntax: Counter Range: 1 to 4294967295 (overflow occurs if this range is exceeded) Description: The total number of enterprise traps sent after starting up ●...
  • Page 189 11. ETHERNET REMOTE CONTROL Specific Trap Type Indication Description LVL_Y_ERR Luminance level error detection LVL_C_ERR Chroma level error detection None (displayed in format information) Unsupported input signal format or an input signal format that is different from the specified format None (displayed in format information) No error (at error recovery, at startup) A_PRTY_ERR...
  • Page 190: Http Server Feature

    11. ETHERNET REMOTE CONTROL 11.4 HTTP Server Feature You can use this feature to control the LV 5770 from a web browser on a PC in the same manner as you would control the LV 5770 from the panel. 11.4.1 Operating Environment The following web browsers have been confirmed to work.
  • Page 191 Press F•1 COMPLETE. The message “Saving data - Please Wait” is displayed. If you changed the IP address, after the message disappears, restart the LV 5770. The IP address value is now valid. Connect the LV 5770's Ethernet port to the network.
  • Page 192 F・D as pressing the corresponding control on the LV 5770. On tab menus and some screens, -50 operates as -5 and +50 operates as +5. Also, in places where the setting resolution is a value other than 1, the value that is set is “resolution ×...
  • Page 193 The timing at which the function menus disappear is different between the LV 5770 and the browser, so when you control a function menu in the browser, the corresponding response may not be what you would expect. In this situation, set MENU Auto Off to a long time in the system menu.
  • Page 194: Sntp Client Function

    11. ETHERNET REMOTE CONTROL 11.5 SNTP Client Function The LV 5770 can display time that is synchronized to an NTP server on the network. 11.5.1 Procedure Configure the Ethernet settings on the LV 5770's ETHERNET SETUP tab. Set SNTP Client Select to ON, and set the IP address, server IP address, and time zone adjustment.
  • Page 195: Time Adjustment Value

    11. ETHERNET REMOTE CONTROL 11.5.2 Time Adjustment Value The date and time exchanged with an NTP (SNTP) are basically Coordinated Universal Time (UTC). Therefore, the time must be adjusted in accordance with the country or region where the device is used in. On the ETHERNET SETUP tab, set Time Zone Adjust to one of the following values.
  • Page 196: 12. Menu Trees

    The default settings are underlined. The settings selected in the tab menu displays are also default settings. The menus that are displayed vary depending on the LV 5770 settings and whether a USB memory device is connected to the LV 5770.
  • Page 197 12. MENU TREES TAB 1 (SDI FORMAT) TAB 2 (REAR PANEL SETUP) TAB 3 (GENERAL SETUP)
  • Page 198 12. MENU TREES TAB 4 (ETHERNET SETUP) TAB 5 (REMOTE SETUP) TAB 6 (DATE&TIME)
  • Page 199: Capture Menu

    12. MENU TREES 12.2 Capture Menu REFRESH ( MANUAL / ERROR ) REFRESH DISPLAY ( REAL / HOLD / BOTH ) FILE ( ON / OFF ) TYPE ( ON / OFF ) ( ON / OFF ) ( ON / OFF ) ( ON / OFF ) menu STORE...
  • Page 200: Preset Registration Menu

    12. MENU TREES 12.3 Preset Registration Menu COMMENT CLEAR INPUT DELETE INSERT <= => CHAR SET menu OVER WR STORE OVER WR DELETE DELETE DELETE ALL COPY COPY USB->INT COPY ALL COPY COPY INT->USB COPY...
  • Page 201: Preset Load Menu

    12. MENU TREES 12.4 Preset Load Menu RCLL NO.1 NO.2 NO.3 NO.4 NO.5 NO.6 more ・ ・ ・ NO.55 NO.56 NO.57 NO.58 NO.59 NO.60 more...
  • Page 202: 13. Change History Of The Software

    • [LV 5770SER08 and LV 5770SER09A] A measurement range setting function was added to the lip sync measurement of the status display. Ver. 5.4 • [LV 5770] Recall menu was improved so that each time the RCLL key is pressed, the menu toggles between show and hide. Ver. 5.2 •...
  • Page 203 • [LV 5770SER08 and LV 5770SER09] Support has been added for HD dual link 1080p/60, 1080p/59.94, and 1080p/50. Ver. 1.6 • [LV 5770] 16:9 and 16:10 squeeze output features have been added to the DVI-D connector. • [LV 5770SER08 and LV 5770SER09] An AFD feature has been added to the picture aspect marker.
  • Page 204 INDEX ALL COPY INT->USB ..........97 LCD OFF ..............81 ALL COPY USB->INT ..........98 LICENSE SETUP ............81 ANALOG AUDIO ............49 MEM ..............94, 96 BMP ................85 MULTI .................57 BSG ................85 PIC MONI OUTPUT ...........44 CAP ................83 COMMENT INPUT ............
  • Page 205 Following information is for Chinese RoHS only 所含有毒有害物质信息 部件号码: LV 5770/5770A/SER03/SER03A/SER08/ SER09/SER09A/SER41/SER42/SER43 此标志适用于在中国销售的电子信息产品,依据2006年2月28日公布的 《电子信息产品污染控制管理办法》以及SJ/T11364-2006《电子信息产品污染 控制标识要求》,表示该产品在使用完结后可再利用。数字表示的是环境保护使 用期限,只要遵守与本产品有关的安全和使用上的注意事项,从制造日算起在数 字所表示的年限内,产品不会产生环境污染和对人体、财产的影响。 产品适当使用后报废的方法请遵从电子信息产品的回收、再利用相关法令。 详细请咨询各级政府主管部门。 产品中有毒有害物质或元素的名称及含量 有毒有害物质或元素 Hazardous Substances in each Part 部件名称 Parts 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(Ⅵ)) (PBB) (PBDE) 实装基板...
  • Page 206 LEADER ELECTRONICS CORP. 2-6-33 Tsunashima-Higashi, Kohoku-ku, Yokohama 223-8505, Japan PHONE:81-45-541-2123 FAX:81-45-541-2823 http://www.leader.co.jp Nov. 26, 2015 Ver. 15 (FW Ver. 5.7)

Table of Contents