Specifications; Troubleshooting - Briggs & Stratton 1450 Series Operator's Manual

1. Remove the fastener (A) and the cover (B).
2. Remove the fastener (C) and the filter (D).
3. Remove the pre-cleaner (E), if equipped, from the filter. To loosen debris, gently tap
the filter on a hard surface. If the filter is excessively dirty, replace with a new filter.
4. Wash the pre-cleaner in liquid detergent and water. Then allow it to thoroughly air
dry. Do not oil the pre-cleaner.
5. Assemble the dry pre-cleaner to the filter.
6. Install the seal washer (F), the filter, and the pre-cleaner, if equipped, into the base
(G) and onto stud (H). Make sure filter is properly assembled into base and secure
with the fastener.
7. Install the cover and secure with the fastener (A). Make sure the fastener is tight.
Foam Filter - Figure 14
1. Loosen the fastener (A) that holds the cover (B).
2. Open the cover and remove the filter (C).
3. Wash the foam element in liquid detergent and water. Squeeze dry the foam element
in a clean cloth.
4. Saturate the foam element with clean engine oil. To remove the excess engine oil,
squeeze the foam element in a clean cloth.
5. Install the filter (C).
6. Install the air filter cover and secure with the fastener.
How To Clean The Air Cooling System - Figure 15
WARNING
Running engines produce heat. Engine parts, especially muffler,
become extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
Allow muffler, engine cylinder and fins to cool before touching.

Remove accumulated debris from muffler area and cylinder area.

NOTICE: Do not use water to clean the engine. Water could contaminate the fuel
system. Use a brush or dry cloth to clean the engine.
This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to
overheat, resulting in poor performance and reduced engine life.
Use a brush or dry cloth to remove debris from the finger guard (A) (Figure 15). Keep
linkage, springs and controls (B) clean. Keep the area around and behind the muffler (C)
free of any combustible debris.
Storage
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Storing Fuel Or Equipment With Fuel In Tank
Store away from furnaces, stoves, water heaters or other appliances that have

pilot light or other ignition source because they can ignite fuel vapors.
Fuel System
Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum
deposits to form in the fuel system or on essential carburetor parts. To keep fuel fresh,
use Briggs & Stratton Advanced Formula Fuel Treatment & Stabilizer, available
wherever Briggs & Stratton genuine service parts are sold.
There is no need to drain gasoline from the engine if a fuel stabilizer is added according
to instructions. Run the engine for 2 minutes to circulate the stabilizer throughout the fuel
system before storage.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into
an approved container. Run the engine until it stops from lack of fuel. The use of a fuel
stabilizer in the storage container is recommended to maintain freshness.
Engine Oil
While the engine is still warm, change the engine oil.

Troubleshooting

Need Assistance? Go to BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in
USA).
10

Specifications

Engine Specifications
Model
Displacement
Bore
Stroke
Engine Oil Capacity
Engine Specifications
Model
Displacement
Bore
Stroke
Engine Oil Capacity
Tune-up Specifications *
Model
Spark Plug Gap
Spark Plug Torque
Armature Air Gap
Intake Valve Clearance
Exhaust Valve Clearance
* Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and
1% for each 10 F (5.6 C) above 77 F (25 C). The engine will operate satisfactorily at
an angle up to 15. Refer to the equipment operator's manual for safe allowable
operating limits on slopes.
Common Service Parts n
Service Part
Foam Air Filter, Round (Model 250000)
Foam Air Filter, Flat
Flat Air Filter
High Capacity Air Filter
Advanced Formula Fuel Treatment &
Stabilizer
Spark Plug (Resistor)
Spark Plug (Non-Resistor)
Spark Plug Wrench
Spark Tester
n We recommend that you see any Briggs & Stratton Authorized Dealer for all
maintenance and service of the engine and engine parts.
190000
18.67 ci (306 cc)
3.228 in (82 mm)
2.283 in (58 mm)
35 -- 39 oz (1.05 -- 1.15 L)
250000
25.63 ci (420 cc)
3.543 in (90 mm)
2.598 in (66 mm)
35 -- 39 oz (1.05 -- 1.15 L)
190000, 250000
0.030 in (0.76 mm)
275 lb-in (31 Nm)
0.008 - 0.016 in (0.2 - 0.4 mm)
0.005 - 0.007 in (0.13 - 0.18 mm)
0.005 - 0.007 in (0.13 - 0.18 mm)
Part Number
799819
591778
491588, 5043
799818
100117, 100120
797235
798615
19605
19368
BRIGGSandSTRATTON.COM