FUTABA R6008HS, R6014HS - FASST receiver Manual

FUTABA R6008HS, R6014HS - FASST receiver Manual

Also See for R6008HS:

Advertisement

FUTABA R6008HS, R6014HS - FASST receiver Manual

Operation Modes

Thank you for purchasing the R6008 HS, R6014HS FASST receiver. These models have two(2) operation mode as shown below.

Normal mode/High Speed mode

The "Normal mode" accepts any type of servos or the peripherals as the frame rate of the output is 14ms. The "High Speed mode" only accept the digital servos for outputs from 1ch to 6ch, including BLS series, and most peripheral equipments such as the gyros or brushless ESCs. The frame rate of the outputs is 7ms. The outputs for other channels indicated below allow to use any type of servos as the frame rate of these outputs are still 14ms on the High Speed mode.
R6008HS - 7ch and 8ch
R6014HS - 7ch to 12ch, DG1, DG2
The R6008HS , R6014HS are compatible with the FASST transmitters as shown below.
TM8 (on 8ch mode), TM10 (on 10ch mode), TM14 (on multi-ch mode)

Usage condition on High Speed mode


Outputs from 1ch to 6ch accept the digital servos only or most type of peripherals.

  • If any analog servos connected to these output as it will cause malfunction. Please check the peripherals if there's any malfunction with whole stick lever throw. If any malfunction occur please change the operation mode to "Normal mode."
  • Output of other channels shown below allow to use any type of servos.
    R6008HS 7ch and 8ch output
    R6008HS - 7ch and 8ch
    R6014HS 7ch to 12ch, DG1, DG2 Outputs
    R6014HS - 7ch to 12ch, DG1, DG2

Device Specifications

  • Dual antenna diversity
  • Power requirement: 4.8V or 6.0V battery or regulated output from ESC, etc. (*1)
  • Size: R6008HS: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)/R6014HS: 2.06 x 1.48 x 0.63 in. (52.3 x 37.5 x 16.0 mm)
  • Weight: R6008HS: 0.48 oz. (13.5g)/ R6014HS: 0.72 oz. (20.8g)

(*1) Be sure that when using ESC's regulated output the capacity of the ESC must meet your usage condition.

Operation Mode Select

The operation mode is on "Normal mode" from factory shipping. When to change the mode, please follow the steps shown below.

  1. Turn off the receiver.
  2. Press and hold the link/mode switch and turn on the receiver. Keep the switch hold more than one(1) second. The LED starts flashing with the current status.
  3. Release the switch.
  4. Turn off the receiver.

By doing this step, the mode can switch over between two(2) modes.
Switching between two operating modes

Please check the operation mode by observing the LED when turning on the receiver. If possible there's no FASST transmitter turned on around you in order to make firmer check.

When turn on the receiver, the LED will be;

  • Red when on "Normal mode"
  • Green and Red (makes Orange) when on "High Speed mode". (After two(2) seconds, change to Red.)

If there are some FASST transmitter turned on around the receiver, the LED may show the above status for a brief moment then changed to the status indication as shown in the "LED indication" table.

LED Indication

Green Red Status
Solid Solid Initializing
Off Solid No signal reception
Solid Off Receiving signals
Blink Off Receiving signals but ID is unmatched
  1. Press and hold the Link/Mode switch more than two(2) seconds.

Re-adjust the F/S position

only for TM-8

  1. Press and hold the Link/Mode switch between one(1) and two(2) seconds.
    Re-adjusting the F/S position


Do not perform the linking procedure with motor's main wire is connected or the engine is operating as it may result in serious injury.
While the linking is done, please cycle receiver power and check if the receiver to be linked is really under the control by the transmitter to be linked.

MPDX-1 application

R6014HS only

When to use the MPDX-1, please prepare the exclusive short-plug shown below.
Using the MPDX-1 - Preparing the short-plug

Using the MPDX-1 - Inserting the short plug
Please insert the short-plug to R6014HS's "DATA" port.

CH11 and CH12 are valid to use of MPDX-1.
Other channels can not use the MPDX-1.

  • When not to use the MPDX-1, do not plug the short-plug to the "DATA" port.
  • Please note that when the short-plug is plugged to the "DATA" port, both CH11 and CH12 become acceptable for MPDX-1. CH11 or CH12 can not separately set as the "MPDX-1-ready-output."

FUTABA CORPORATION
Phone: (043) 296-5118
Makuhari Techno Garden Bldg., B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan

©FUTABA CORPORATION

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download FUTABA R6008HS, R6014HS - FASST receiver Manual

Advertisement

Need help?

Need help?

Do you have a question about the R6008HS and is the answer not in the manual?

Questions and answers

Table of Contents