FUTABA R6108SB Manual

FUTABA R6108SB Manual

S.bus compatible/fasst-2.4ghz (multi-ch) system 8 channels/high-speed receiver

Advertisement

R6108SB
Thank you for purchasing a Futaba R6108SB S.BUS
compatible receiver.
The R6108SB has an S.BUS system output port and a
conventional system channel output. It can also be used with
conventional system servos, etc. in addition to S.BUS system
compatible servos and gyros, etc.
In addition, the operating mode (high-speed mode/normal
mode) can be selected.
* However, channel outputs 7 and 8 for conventional system oper-
ate in the normal mode even if set to the high-speed mode.

Applicable systems:

, TM10
10ch mode)
(on 10ch mode)
DATA port
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model
number R6108SB, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

What is S.BUS?

Different from conventional radio control systems the S.BUS
system uses data communication to transmit control signals
from a receiver to a servo, gyro, or other S.BUS compatible
device. This data includes commands such as "move the
channel 3 servo to 15 degrees, move the channel 5 servo to
[Connection by S.BUS system]
Battery
* Can also be used together with conventional servos.
S.BUS compatible/FASST-2.4GHz (Multi-ch) system
8 channels/high-speed receiver
T8FG 2.4GHz
(on 8ch mode)
, TM14
(on multi-ch mode)
Link/Mode switch
R6108SB
LED
R6108SB
Ch output/
Battery terminal
S.BUS hub
S.BUS
S.BUS output
2ch
Conventional
servo
Usage condition on "High Speed mode"
 CAUTION
When using the high-speed mode, use a Futaba

digital servo (including brushless servo) or S.BUS
servo at conventional system use channels 1 to 6.
Analog servos cannot be used.
• The use of analog servos may cause servo trouble.
• When using analog servos, select the normal mode, and
use channel outputs 7 and 8.
, TM8
, T10CG 2.4GHz
(on 8ch mode)
• Channel outputs for conventional
system (1 to 8)
• Battery terminal (B)
• S.BUS Port (S.BUS)

R6108SB Specifications

S.BUS compatible/FASST-2.4GHz (Multi-ch) system/8 channels/
high-speed receiver
• Dual antenna diversity
• Power requirement: 4.8V or 6.0V battery or regulated out-
put from ESC, etc. (*1)
• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)
• Weight: 0.49 oz. (13.8g)
(*1) Be sure that when using ESC's regulated output the capacity of
the ESC must meet your usage condition.
30 degrees" to multiple devices. The S.BUS devices execute
only those commands for their own set channel. For this
reason, it can be used by connecting multiple servos to the
same signal line.
3ch
5ch
S.BUS hub
6ch
4ch
S.BUS servo
(on

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the R6108SB and is the answer not in the manual?

Questions and answers

Summary of Contents for FUTABA R6108SB

  • Page 1 Usage condition on "High Speed mode" compatible receiver.  CAUTION The R6108SB has an S.BUS system output port and a conventional system channel output. It can also be used with When using the high-speed mode, use a Futaba conventional system servos, etc. in addition to S.BUS system digital servo (including brushless servo) or S.BUS...
  • Page 2 Release the switch. S.BUS Servo Channel Setting Method Turn off the receiver. S.BUS servo channel setting can be performed at the R6108SB By doing this step, the mode can switch over between two(2) receiver. modes. Connect the accessory short-plug to the DATA port of Turn on the receiver.

Table of Contents

Save PDF