FUTABA R6203SBE Manual

R6203SBE
Thank you for purchasing a Futaba R6203SBE FASST-2.4GHz
compatible receiver.
The R6203SBE has an S.BUS system output port and a
conventional system channel outputs. It can also be used with
conventional system servos, etc. in addition to S.BUS system
compatible servos and gyros, etc.
When the linking procedure is performed, R6203SB
recognizes the signal mode (FASST-2.4GHz 7ch mode or
8ch/10ch/Multi-ch mode) automatically.
In addition, the operating mode (high-speed mode/normal
mode) can be selected.
Applicable systems: FASST-2.4GHz 7ch or 8ch/10ch/Multi-ch system
WARNING
If a part of the fuselage is made of
conductive materials such as metal and
carbon, install the receiver so that it is never
covered with these materials and the antenna
never touch them.
or loss of control.
Do not use it for a middle or large scale
model.
diameter.
or large scale model.
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model
number R6203SB, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)
FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) System
S.BUS Port and 3 Channels for Conventional System
High-speed Receiver
For parkflight or indoor use airplanes.
For small size electric helicopters

Link/Mode switch

LED
R6203SBE
Usage condition for conventional system
output (Ch1-3) on "High Speed mode"
CAUTION
The "High Speed mode" accept the digital servos
only or most type of peripherals.
"Normal mode."

Usage precautions about the power source

We do not recommend to use the power source of less than
4.0V but if to use the lower voltage source please keep in
mind the condition shown below.
start flight.
This is very important since the receiver will stop operation
The power source voltage must not exceed the servo's
rating.
system (2)
system (1)
system (3
S.BUS
56%( 6SHFLÀFDWLRQV
FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) system/S.BUS port
and 3 channels for conventional system/high-speed receiver
‡ 6L]H  [  [  LQ  [  [  PP
‡ :HLJKW  R] J
‡ 3RZHU UHTXLUHPHQW 9 WR 9 9ROWDJH UDQJH  WR 9
%H VXUH WKDW ZKHQ XVLQJ (6& V UHJXODWHG RXWSXW WKH FDSDFLW\ RI WKH (6&
PXVW PHHW \RXU XVDJH FRQGLWLRQ
* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S
function doesn't work properly when other type battery is used.
7KH IDLO VDIH IXQFWLRQ FDQ EH VHW IRU HDFK FKDQQHO ZKHQ RQ 0XOWLFK PRGH
KRZHYHU LW GLIIHUV DFFRUGLQJ WR WKH WUDQVPLWWHU :KHQ RQ FK PRGH WKH
IDLO VDIH IXQFWLRQ FDQ EH VHW IRU FKDQQHO RQO\
* S.BUS SRUW 56% FDQ EH XVHG XS WR  FKDQQHOV RU OHVV RQ WKH FK
PRGH DQG  FKDQQHOV  '* RU OHVV RQ WKH FKFK0XOWLFK PRGH
KRZHYHU LW GLIIHUV DFFRUGLQJ WR WKH WUDQVPLWWHU
B)
S.BUS)