FUTABA TM-7 Instruction Manual

Range Check the Radio
1
Turn on the transmitter. Wait until the RF signal
becomes stable.(LED is solid green or blink)
2
Press and hold the function switch on the TM-7 then
the RF power is reduced so the range test can be
performed. While RF power is being reduced, the red LED
on the TM-7 becomes blinking.
Note: Please be careful that if press and hold the switch
before turn on the transmitter then the F/S status
is changed. To avoid this situation, please wait
for while after turn on the transmitter then start
ground range check.
3
Walk away from the model while simultaneously
operating the controls. Have an assistant stand
by the model and signal what the controls are doing to
confirm that they operate correctly. You should be able to
walk approximately 30 - 50 paces from the model without
losing control.
4
If everything operates correctly, return to the model.
Set the transmitter in a safe, yet accessible location
so it will be within reach after starting the engine. Be
certain the throttle stick is all the way down, then start the

Repair Service

Before requesting repair, read this instruction manual again and recheck your
system. Should the problem continue, request repair service as follows:
Describe the problem in as much detail as possible and send it with a detailed
packing list together with the parts that require service.
• Symptom (Including when the problem occurred)
• System(Transmitter, Receiver, Servo's and model numbers)
• Model (Model name)
• Model Numbers and Quantity
• Your Name, Address, and Telephone Number.
If you have any questions regarding this product, please consult your local
hobby dealer or contact the Futaba Service Center.
Special Markings;
Pay special attention to the safety at
the parts of this manual that are
indicated by the following marks.
[Symbol]
; Prohibited ; Mandatory
FUTABA CORPORATION
Makuhari Techno Garden Bldg., B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan
engine. Perform another range check with your assistant
holding the plane and the engine running at various
speeds. If the servos jitter or move inadvertently, there
may be a problem. Do not fly the plane! Look for loose
servo connections or binding pushrods. Also be certain
that the battery has been fully charged.
5
NEVER press and hold the function switch when
flying as it cause loss of total control!

Other precautions

1
When utilizing the trainer function of the transmitter
as a instructor, please do not switch to the student's
control until the RF starts output after turn on the power.
Otherwise it may cause malfunction.
Mark Meaning
Procedures which may lead to a dangerous condition and cause
death or serious injury to the user if not carried out properly.
Procedures which may lead to a dangerous condition or cause death
or serious injury to the user if not carried out properly, or procedures
where the probability of superficial injury or physical damage is high.
Procedures where the possibility of serious injury to the user is
small, but there is a danger of injury, or physical damage, if not
carried out properly.
Phone: (043) 296-5118 Facsimile: (043) 296-5124
©FUTABA CORPORATION 2007, 05 (1)
- 4 -
TM-7 RF Module
and
R607FS Receiver
I M
NSTRUCTION ANUAL
Applicable system;
T7U, T8U, T9C, T9Z, FC-18 Plus
or FC-28 Transmitter
Contents and Technical Specifications
Your 2.4GHz system includes the following components;
TM-7 RF Module
[Specification]
TM-7 RF Module:
• Communication system: One-way communication
• Antenna: 1/2 wavelength di-pole.
• Current consumption: 150mA max.
• Setting switch for F/S setting and range check
• Monitor LED for indication of operation status
R607FS Receiver:
• Diversity antenna
• Power requirement: 4.8V or 6.0V battery or regulated out put from ESC, etc.
• When using NiCd or NiMH, the 4-cell is recommended as it makes effective use
of the battery f/s function. (Never use Dry batteries as it cause malfunctions)
• F/S and Battery F/S function for throttle CH. (3rd Ch.)
• Size: 1.64x1.08x0.36 in. (41.6x27.5x9.2 mm)
• Weight: 0.34 oz. (9.8 g)
IMPORTANT: Since the 2.4GHz have different characteristics than
that of the conventional 27MHz and 72MHz frequencies, please read
this manual carefully to enjoy safe flight with the 2.4GHz system.
Thank you for purchasing the TM-7 2.4G FASST RF-module and R607FS
FASST 7ch-receiver. The system can be utilized with Futaba transmitters
of listed below. In order to use the TM-7, just replace it with the
conventional RF- module. The receiver R607FS can output up to 7ch of
servo control signal. Installation of the receiver needs special attention and
please follow our guideline to enjoy safe flight with TM-7 and R607FS
with your transmitter!
Features
• 2.4GHz Spread Spectrum radio communication system
• Exclusive ID code for avoiding a jamming from other FASST system.
• Fail Safe(F/S) function(for throttle Ch.)---F/S, Battery F/S
• Diversity antenna(R607FS)
USAGE PRECAUTIONS
1. If there is a special regulation for using 2.4GHz radio systems at your
flying site, please obey all regulations to enjoy safe flying with your
2.4GHz system.
2. 2.4GHz is very different than the frequencies we currently use. Please
keep the model in sight at all times as large objects can block the RF
signal. Please keep in mind that objects such as wire fences and wire
mesh will also cause loss of signal.
3. NEVER grip the transmitter antenna when flying as this degrades RF
quality and cause loss of control.
• No part of this manual may be reproduced in any form without prior per-
mission.
• The contents of this manual are subject to change without prior notice.
• This manual has been carefully written. Please write to Futaba if you feel
that any corrections or clarifications should be made.
R607FS Receiver
Mini screwdriver
- 1 -
1M23N