1M23N17476
R6208SB
Thank you for purchasing a Futaba
compatible receiver.
The
has an
R6208SB
S.BUS
conventional system channel output. It can also be used with
conventional system servos, etc. in addition to
compatible servos and gyros, etc.
In addition, the operating mode (high-speed mode/normal
mode) can be selected.
* However, channel outputs 7 and 8 for conventional system oper-
ate in the normal mode even if set to the high-speed mode.
A p p l i c a b l e s y s t e m s :
, T M 1 0
1 0 c h m o d e )
(o n 1 0 c h m o d e )
Link/Mode
port
DATA
R6 2 0 8 SB
S.BUS c onnec t or inser t ion pr ec aut ion
DA N GER
Do not insert a connector, as shown right.
• It will occur short-circuit, by inserting this way. A short
circuit across the battery terminals may cause abnormal
heat, fire and burning.
Co m p l i a n c e I n fo r m at i o n St at e m e n t
(fo r U.S.A .)
This device, trade name Futaba Corporation, model number
R6208SB, complies with part15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesiredoperation.
The responsible party of this device compliance is:
FUTABA Corporation of America
2681 Wall Triana Hwy Huntsville, AL 35824, U.S.A.
Phone:1-256-461-9399 FAX:1-256-461-1059
E-mail: service@futabaUSA.com
compatible/
S.BUS
FASST-2.4GHz
high-speed receiver
• Dual antenna diversity
• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)
• Weight: 0.49 oz. (13.8g)
• Power requirement: 3.7V to 7.4V
(Voltage range: 3.5 to 8.4V)
* Be sure that when using ESC's regulated output the capacity of the ESC
must meet your usage condition.
* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S
function doesn't work properly when other type battery is used.
S.BUS compatible/FASST-2.4GHz (Multi-ch) system
8 channels/high-speed receiver
R6208SB S.BUS
system output port and a
system
S.BUS
T 8 FG 2 .4 GH z
(o n 8 c h m o d e )
, T M 1 4
(o n m u l t i -c h m o d e )
switch
LED
(Multi-ch) system/8 channels/
U s a g e c o n d i t i o n o n " H i g h Sp e e d m o d e "
CAUTION
When using the high-speed mode, use a Futaba
digital servo (including brushless servo) or
at conventional system use channels
servos cannot be used.
• The use of analog servos may cause servo trouble.
• When using analog servos, select the normal mode, and
use channel outputs 7 and 8.
, T M 8
(o n 8 c h m o d e )
• Channel outputs
for conventional
system (
to
)
1
8
• Battery terminal (
)
B
•
Port (
)
S.BUS
S.BUS
8CH/Battery(8/B)
8CH/Battery(8/B)
DA N GER
Do not insert either a switch
or battery in this manner.
Wh at i s S.BU S?
Different from conventional radio control systems the
system uses data communication to transmit control signals from
a receiver to a servo, gyro, or other
data includes commands such as "move the channel 3 servo to
15 degrees, move the channel 5 servo to 30 degrees" to multiple
devices. The
devices execute only those commands for their
S.BUS
own set channel. For this reason, it can be used by connecting
multiple servos to the same signal line.
[ Co n n e c t i o n b y S.BU S s y s t e m ]
Ch output/
R6208SB
Battery terminal
S.BUS hub
S.BUS
S.BUS output
Battery
Conventional
servo
* Can also be used together with conventional servos.
* When using servos with a remote battery pack, use S.BUS Hub
with Cable (2-way/remote battery pack use).
Please refer to the instruction manual of S.BUS Hub with Cable
(2-way/remote battery pack use) for the connection method.
servo
S.BUS
to
. Analog
1
6
, T 1 0 CG 2 .4 GH z
(o n
7CH
7CH
S.BUS
S.BUS
compatible device. This
S.BUS
3ch
5ch
S.BUS hub
6ch
2ch
4ch
S.BUS servo
Need help?
Do you have a question about the R6208SB and is the answer not in the manual?
Questions and answers