Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for unicraft RFW 0,5,
- Page 1 Operating Instructions Roller Driver RFW 0,5, RFW 1 RFW 2, RFW 3 RFW 5 RFW 1...
-
Page 2: Table Of Contents
4.1 Type plate............7 5 Transport, packaging, storage.......7 Fax: 0049 (0) 951 96555 - 55 5.1 Delivery............... 7 5.2 Packaging............7 E-Mail: info@unicraft.de 5.3 Storage ............... 7 Internet: www.unicraft.de 6 Description of device ..........8 6.1 Image..............8 6.2 Scope of delivery..........8 Indications regarding the operating instructions 7 Mounting ..............8... -
Page 3: Introduction
All data in these operating instructions has been com- You have made a good choice by purchasing a piled on the basis of the state-of-the-art, valid standards UNICRAFT roller driver. and guidelines as well as our many years of expertise and experience. -
Page 4: Obligations Of The Operating Company
Safety roller driver must be met. The following applies in par- ticular: WARNING! This combination of symbol and signal term indi- - The operator must inform himself about the cates potentially hazardous situations which may applicable occupational health and safety regula- cause death or serious injury if not averted. -
Page 5: Personal Protective Equipment
Safety Only persons reliable working procedures can be expected from, are allowed to perform all works. Persons the responsi- Safety boots veness of which is affected by e. g. drugs, alcohol or medication, are not allowed to work with the machine. The safety boots protect the feet against crushes, falling parts and slipping over on slippery under- The qualifications of the personnel for the different tasks... -
Page 6: Safety Information For Operating Personnel
Intended Use Intended Use 2.6 Safety information for operating personnel No operational mode which could compromise the The roller driver is used exclusively for transporting sus- safety of the roller driver may be undertaken. pended loads up to the specified maximum load on a suitable steel girder. -
Page 7: Technical Data
Technical Data Technical Data 4.1 Type plate Load-carrying 1000 2000 capacity [kg] Carrier flange width 55-220 58-220 66-220 [mm] Curve radius min. [m] Length A [mm] Fig. 3: Type plate Width/Depth B [mm] Height C [mm] Transport, packaging, storage Loop thickness D 12,5 [mm] 5.1 Delivery... -
Page 8: Description Of Device
Description of device Description of device Mounting The personal protective equipment is explained in the 6.1 Image following paragraph: Illustrations in these operating instructions may deviate from Head protection the original. Use protective gloves! Wear safety boots! Wear protective clothes! The roller driver can be adapted to the width of the girder (rail width 55 - 220 mm, min. -
Page 9: Care, Maintenance And Repair
Care, maintenance and repair Care, maintenance and repair Visual inspection and maintenance Maintenance Maintenance tasks 8.1 Care by cleaning intervals The roller driver must always be kept in a clean condition. before each Check the roller driver for damage operation and wear, look particularly at the ca- ble and check for deflection, stretch- ing, fissures or corrosion. -
Page 10: Inspecting The Roller Driver
Inspecting the roller driver Inspecting the roller driver The use of the roller driver is possible after: UVV "Winches, lifting and pulling equipment" BGV D8 (VBG 8), UVV "Cranes" BGV D6 (VBG 9) Inspection by a specialist prior to initial commissioning and after major changes when used in accordance with BGV D8 §... -
Page 11: Disposing Of Lubricants
Spare parts 10.2 Disposing of lubricants Example The threaded rod for the roller driver RFW 1 must be Lubricant manufacturers provide disposal information ordered. The threaded rod is identified in the spare for the lubricants used. If necessary, request product- parts drawing with the number 7. -
Page 12: Eu Declaration Of Conformity
According to Machinery Directive 2006/42/EC Annex II 1.A Stürmer Maschinen GmbH Manufacturer / distributor: Dr.-Robert-Pfleger-Straße 26 D-96103 Hallstadt hereby declares that the following product Unicraft® Werkstatttechnik Product group: Roller Driver Machine type: Designation of the machine: Item number: RFW 0,5... -
Page 13: Maintenance Schedule
Maintenance schedule 13 Maintenance schedule Maintenance schedule 40 h 200 h As required Annually Data Operating Staff Signature hours RFW-Series | Version 1.01... - Page 14 www.unicraft.de...