Maintenance & Service - Skil 5330AA Instructions Manual

! set cutting depth so that you cut through panel
and not through support
- in case parallel guide does not allow desired width of
cut, clamp or nail straight piece of wood to workpiece
as a guide, and use the right side of the foot against
this guide
• Splinter-free cutting
- always face the good side of the workpiece down
- fasten a straight piece of wood on the workpiece by
means of 2 clamps
• For more tips see www.skil.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots Y 2)
! disconnect the plug before cleaning
• Always keep the area around lower guard Z 2 clean
(remove dust and chips by blowing out with compressed
air or with a brush)
• Clean saw blade immediately after use (especially from
resin and glue)
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 7 will remind you of this when the need for
disposing occurs
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 94 dB(A) and the sound
power level 105 dB(A) (standard deviation: 3 dB), and the
vibration ✱ (triax vector sum; uncertainty K = 1.5 m/s²)
✱ cutting wood 2.9 m/s²
✱ cutting metal 2.8 m/s²
✱ cutting tiles 2.8 m/s²
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Scie compacte polyvalente
INTRODUCTION
• Cet outil est prévu pour scier longitudinalement et
transversalement du bois, des panneaux de particules,
des panneaux en contreplaqué, de l'aluminium, des
dalles, de la pierre, des matériaux de construction en
plastique et légers, maintenu(s) en position fixe
• Cet outil est conçu uniquement pour des coupes de
brève durée
• Cet outil n'est conçu pour un usage professionnel
• Lisez attentivement ce manuel d'instruction avant
d'utiliser l'outil et conservez-le pour pouvoir vous y référer
ultérieurement 4
CARACTERISTIQUES TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Interrupteur de sécurité
B Gâchette
C Pince pour régler la profondeur de coupe
D Échelle de profondeur de coupe
E Tuyau d'extraction des poussières
F Connexion pour l'extraction des poussières
G Clé hexagonale
H Rangement pour la clé hexagonale
J Bouton de blocage de l'arbre
K Boulon de la lame
L Bride de serrage
M Bouton pour le sciage en plongée
N Semelle
P Protection supérieure
Q Témoin d'alimentation
R Indicateur de la ligne de coupe
S Guide parallèle
T Bouton de réglage du guide longitudinal
V Lame de scie en acier trempé
W Disque diamanté
X Lame de scie avec denture à mise de carbure
Y Fentes de ventilation
Z Carter intérieur
16
5330