Philips 180P1L/00 Service Manual
Philips 180P1L/00 Service Manual

Philips 180P1L/00 Service Manual

1 8" tft lcd colour monitor

Advertisement

Quick Links

18" TFT LCD Colour Monitor
Service
Service
Service
DVI-D & D-SUB Dual Input/DDC/Audio
Auto Picture Adjustment/Wide Viewing Angle
Description
Important Safety Notice..................................2
Technical Data & Power Management ............3~4
Connection to PC...........................................5
Installation & Accessories...............................6
Description of Controls...................................7
Advanced Control of OSD...............................8
Clock & Phase Adjustments............................9
OSD Menu Control Level Structure.................10~11
OSD Attention Signal.....................................12
Troubleshooting............................................13
Failure Mode of LCD Panel.............................14
Flat Panel Adjust (FP Adjust)......................... 16
Definition Of Pixel Defects..............................17
Wiring Diagram..............................................18
Mechanical Instructions..................................19~21
Electrical Instructions.....................................22~23
Factory Adjustment........................................24
Safety test Requirements...............................25
DDC Instructions............................................26~29
DDC Data.......................................................30~31
Repair Flow Chart...........................................32~35
Colour Adjustment..........................................36~42
PCBA Architecture..........................................43
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC
EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Published by BCU Monitor
Printed in Taiwan

TABLE OF CONTENTS

Page
Description
Power Distribution Flow...................................44
Block Diagram & Control Panel C.B.A...............45
AC Adapter Schematic Diagram and C.B.A.......46
DC Converter & Video in Schematic Diagram....47
RGB Digitizer Diagram and Waveforms.............48
Scaling Schematic Diagram and Waveforms......49
MCU Schematic Diagram and Waveforms..........50
Frame buffer and Power Saving Diagram...........51
Audio & Control Panel Schematic Diagram.........52
TMDS Receiver and Main Panel C.B.A...............53
TTL to LVDS Signal Converter Diagram..............54
Audio Panel C.B.A............................................55
Repair tips .......................................................56
Exploded View..................................................57
Recommended Parts List...................................58
Spare Parts List................................................59~64
General Product Specification...........................65~87
LG LCD Panel...................................................88
Inverter Schematic Diagram (I)..........................89
Inverter Schematic Diagram (II).........................90
Inverter Panel C.B.A.........................................91
Spare Parts List for Inverter...............................93
Spare Parts List for Inverter...............................94
©
Copyright reserved
Subject to modification
180P1L/00(LG panel)
Horizontal frequencies
July 21 2000
30 - 82 kHz
Page
3138 106 10105
GB

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 180P1L/00 and is the answer not in the manual?

Questions and answers

Summary of Contents for Philips 180P1L/00

  • Page 1: Table Of Contents

    18" TFT LCD Colour Monitor Service Service Service DVI-D & D-SUB Dual Input/DDC/Audio 180P1L/00(LG panel) Auto Picture Adjustment/Wide Viewing Angle Horizontal frequencies TABLE OF CONTENTS 30 - 82 kHz Page Description Description Page Power Distribution Flow........44 Important Safety Notice........2 Technical Data & Power Management ....3~4 Block Diagram &...
  • Page 2: Important Safety Notice

    Under no circumstances should the original design be modified or altered without written permission from Philips. Philips assumes no liability, express or implied, arising out of any unauthorized modification of design. Servicer assumes all liability. * Broken Line...
  • Page 3 Technical Data 180P LCD Go to cover page Pin Assignment Technical Specifications D-Sub connector LCD Panel Screen type : LG Active matrix - TFT LCD Screen dimensions : 18.1 inches (diagnoal) Preset display area Horizontal : 359 mm Vertical : 287 mm Pin No.
  • Page 4 ENERGY STAR is a U.S. registered mark. AS AN ENERGY STAR 1 640X350 31.5K/70HZ 25.175 (+/-) IBM VGA 10h PARTNER, PHILIPS HAS DETERMINED THAT THIS PRODUCT 2 720X400 31.5K/70HZ 28.322 (-/+) IBM VGA 3h MEETS THE ENERGY STAR GUIDELINES FOR ENERGY 3 640X480 37.5K/75HZ...
  • Page 5: Connection To Pc

    Connection to PC 180P LCD Go to cover page Please follow the steps to connect your LCD Monitor to PC. NOTE: If you use an Apple Macintosh™, you need to connect the special Mac adapter to one end of the monitor signal cable. 1.
  • Page 6: Installation & Accessories

    Installation & Accessories 180P LCD Go to cover page Installation Locations Pedestal With the built-in pedestal, you can tilt or swivel the monitor for the most Avoid Heat and Extreme Cold comfortable viewing angle. 1. Do not store or use the LCD monitor in locations exposed to heat, direct sunlight, or extreme cold.
  • Page 7: Description Of Controls

    Description of Controls 180P LCD Go to cover page FRONT VIEW Power Button - Turns the monitor On or Off. Built-in Microphone -Allows you to speaker into your computer. LED - Light Emitting Diode turns green when the monitor is on. Speakers - Transmit sounds from your AUTO Adjust Button-...
  • Page 8: Advanced Control Of Osd

    Advanced control of OSD 180P LCD Go to cover page Front control panel Recover attention signals by pressing button for more than 10 seconds without video signal input. ATTENTION ATTENTION SIGNAL ON To Lock/Unlock OSD function The OSD function can be locked by pressing button for more than Access Service Mode 10 seconds, the screen shows following windows for 3 seconds.
  • Page 9: Clock & Phase Adjustments

    CLOCK & PHASE Adjustments 180P LCD Go to cover page Step 3 : Remaining Shut Down Window on the screen , follow Due to the different quality of video signal generated from graphics cards. It is necessary to adjust CLOCK and PHASE functions for the The CLOCK and PHASE adjustment instructions for the optimal video display of LCD monitor.
  • Page 10 OSD Control Structure for Analog 180P LCD Go to cover page The OSD Tree for analog video signal Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments.
  • Page 11 OSD Control Structure for Digital 180P LCD Go to cover page The OSD Tree for digital video signal (DVI-D) This OSD structure is different from analog menu, there are three functions will be disable on digital OSD menu: Contrast, Image Optimization, and Adjust Color.
  • Page 12: Osd Attention Signal

    OSD Attention signals 180P LCD Go to cover page The monitor will detect various display situation automatically. When ENTERING SLEEP MODE the monitor detects the problems, the screen will show the different This screen appears when the monitor is about to enter the sleep warning signals to remind you what is happen to your monitor.
  • Page 13: Troubleshooting

    Trouble Shooting 180P LCD Go to cover page TROUBLESHOOTING Horizontal flicker Push the Auto button. appears Eliminate the horizontal bars using the Phase This page presents problems that can be corrected by the user. If the Adjustment in the First Window. problem still exists after these possible solutions, a further action has to be take by authorized technicians.
  • Page 14: Failure Mode Of Lcd Panel

    Failure Mode of LCD panel 180P LCD Go to cover page Quick reference for failure mode of LCD panel This page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the “Mechanical instruction”...
  • Page 15: Usb Connection & Usb Hub Installation

    USB Connections & USB Hub installation 180P LCD Go to cover page USB Introduction Application USB (Universal Serial Bus ) is an innovation in connecting your IBM- Just a few peripherals you can connect to your USB Hub . compatible computer to your monitor. By using the optional USB HUB, you will be able to connect optional USB type keyboards, mice, printers, and other peripherals to your monitor instead of having to connect them to your computer.
  • Page 16: Flat Panel Adjust (Fp Adjust)

    Fpadjust program The Flat Panel Adjust (FPadjust) software helps you to find the best setting for your Philips LCD monitor. It allows you to adjust the image performance of LCD monitor, such as RESOLUTION, AUTO ADJUSTMENT, POSITION, CONTRAST, IMAGE OPTIMIZATION.
  • Page 17: Definition Of Pixel Defects

    In order to qualify for repair or replacement due to pixel defects This section explains the different types of pixel defects and during the warranty period, a TFT LCD panel in a PHILIPS flat defines acceptable defect levels of each type. In order to qualify...
  • Page 18: Wiring Diagram

    Wiring Diagram 180P LCD Go to cover page Back Forward...
  • Page 19: Mechanical Instructions

    Mechanical instructions 180P LCD Go to cover page General To be able to perform measurements and repairs on the circuit boards, Spread a soft mat underneath to avoid damaging the LCD surface. 1. Rear cover removal Step 1 : To remove the back cover, press up to disengage the clips on each side, then pull and lift as shown in Fig.1 Step 2 : Remove plastic ring from the hinge.
  • Page 20 Mechnical instructions 180P LCD Go to cover page Fig. 11 Fig. 8 5. Inverter PCB removal Note: The fluorescent lamps are consumable. When replace Step 1 : Disconnect three connectors (A) and remove screw (B). the lamps, both upper and lower See Fig.
  • Page 21 Mechanical instructions 180P LCD Go to cover page Fig. 3 Recommended service position Forward Back...
  • Page 22: Electrical Instructions

    Electrical instructions 180P LCD Go to cover page PRESET VIDEO RESOLUTION 0. General Factory preset video resolution Resolution Frequency Pixel rate Sync Comment When carry-out the electrical settings in many cases a video 1 640X350 31.5K/70HZ 25.175 (+/-) IBM VGA 10h signal must be applied to the monitor.
  • Page 23 Electrical instructions 180P LCD Go to cover page Use Minolta CA-110 for color coordinates and luminance check. Luminance; 155 Nits (LG) in the center of the screen. 4.4 Check the digital interface Set the delay time to be 6 nsec. Check the 64 gray level color poor &...
  • Page 24: Factory Adjustment

    Factory Adjustment 180P LCD Go to cover page PRESET VIDEO RESOLUTION Factory Mode Adjustment (PS: The “Offset R G B” function can be used on reduce or eliminate snowy noise on the background when the resolution of video signal is Entering Factory Adjustment Menu 1024 X 768 vertical 60Hz.
  • Page 25: Safety Test Requirements

    Safety Test Requirements 180P LCD Go to cover page All units that are returned for service or repair must pass the 3. Equipments and Connection original manufactures safety tests. Safety testing requires both Hipot Ground Continuity testing. 3.1. Equipments For example : HI-POT TEST INSTRUCTION - ChenHwa 9032 PROGRAMMABLE AUTO SAFETY TESTER...
  • Page 26: Ddc Instructions

    DDC Instructions 180P LCD Go to cover page PRESET VIDEO RESOLUTION 1. General Note: The alignment box has already build-in a batteries socket for using batteries (9V) as power source. Pull out the socket by DDC Data Re-programming remove four screws at the rear of box. Please do not forget that remove batteries after programming.
  • Page 27 DDC Instructions 180P LCD Go to cover page 4. Configuration and procedure Re-programming Digital DDC IC Step 1: Connecting all cables and alignment box as shown on Fig. 4 There are three chips contained serial number on the circuit board, Step 2: Press and hold “...
  • Page 28 DDC Instructions 180P LCD Go to cover page 4. Click button. The main menu appears (as shown on Fig. 6). Command bar Tools bar Status bar Fig. 6 Note: If the connection is improper, you will see the following error message before entering the main menu.
  • Page 29 DDC Instructions 180P LCD Go to cover page Definition of Serial Number Write DDC data to monitor T Y 0 0 9 9 2 8 0 0 0 0 0 1 Click icon from the tools bar to starting rewrite DDC data. Click for confirmation.
  • Page 30 DDC Instructions 180P LCD Go to cover page Standard Timing Identification #3 THE DISPLAY DATA CHANNEL (DDC)1/2B CONTENT INCLUDING Horizontal active pixels : 1024 Aspect Ratio : 4:3 (FOR LG ANALOG) Refresh Rate : 85 Vendor/Product Identification Standard Timing Identification #4 ID Manufacturer Name : PHL Horizontal active pixels...
  • Page 31: Ddc Data

    DDC data of Digital 180P LCD Go to cover page THE DISPLAY DATA CHANNEL (DDC) 1/2B CONTENT INCLUDING Standard Timing Identification #4 (FOR LG DIGITAL) Horizontal active pixels : 1024 Aspect Ratio : 4:3 Vendor/Product Identification Refresh Rate : 75 ID Manufacturer Name : PHL ID Product Code...
  • Page 32: Repair Flow Chart

    Repair Flow Chart 180P LCD Go to cover page Block Diagram AC IN AC adapter 18V DC Front control 18VCC 18V DC Inverter panel Main panel panel 18V DC Audio control Fluorescent Speaker LCD panel panel Lamp No power (power indicator off) Check Bad AC adapter Bad AC adapter...
  • Page 33 Repair Flow Chart 180P LCD Go to cover page No Raster Check Bad AC adapter Bad AC adapter AC adapter output 18V DC Check video signals input Video source interface Check Replace fluorescent Inverter panel lamp Replace inverter Replace main panel panel Front control key does not work...
  • Page 34 Repair Flow Chart 180P LCD Go to cover page Bad brightness Check Bad Inverter Inverter panel output panel Replace fluorescent lamp Replace LCD panel Bad image Check Video,fh/fv,DVI-I signals Replace main panel Check all connectors Replace LCD panel Back Forward...
  • Page 35 Repair Flow Chart 180P LCD Go to cover page No sound Check mute function & audio signal source Check Bad audio Audio panle 18V&power panel , volume controls Check Control panel connectors 1910, 1909 Replace main panel Back Forward...
  • Page 36: Colour Adjustment

    Colour adjustment 180P LCD Go to cover page LCD COLOUR ANALYZER - CA110 1. SUMMARY The LCD Colour Analyzer CA-110 was designed to upgrade the white-balanceprocess on production lines for colour LCD televisions and computer colour LCD panels in the colour LCD industry. The CA-110 consists of a main unit and a measuring probe. The measuring probe utilizes an optical system suitable for measurement of colour LCDs and is equipped with a viewfinder to verify the area to be measured.
  • Page 37 Colour Adjustment 180P LCD Go to cover page Back Forward...
  • Page 38 Colour adjustment 180P LCD Go to cover page ZERO CALIBRATION Zero calibration is performed to determine the output of the measuring probe when no light reaches the sensor and to set this as the zero point to which all other measurements are referenced. Zero calibration must be performed after the POWER switch has been set ON brfore taking any measurements.
  • Page 39 Colour Adjustment 180P LCD Go to cover page SETTING MEASUREMENT AREA Measurement areas of 25mm and 50mm can be selected by extending or retracting the lens barrel. The 25mm measurement area can be used for measuring LCDs with 2 - inch or greater diagonals: the 50mm measurement area can be used for measuring LCDs with 4 - inch or greater diagonals.
  • Page 40 Colour adjustment 180P LCD Go to cover page SETTING MEASUREMENT DISTANCE The measurement distance (the distance from the front of the measuring probe's lens barrel to the display surface of the LCD ) should be set using a ruler according to the procedure below. 1.
  • Page 41 Colour Adjustment 180P LCD Go to cover page White Balance Adjustment 5. Adjust OSD menu to lower position of screen (i.g. adjust V-position to value “ 0” at submenu of OSD Setting. 6. Setting Brightness and Contrast Alignment procedure - Adjust Brightness to value “100”. - Adjust Contrast to value “50”.
  • Page 42 Colour adjustment 180P LCD Go to cover page 15. Gray scale checking - Switch Timing/pattern generator to Pattern: 32 gray scale Timing: 1280 X 1024 75Hz 60KHz - Setting both Brightness and Contrast to 50 (Value). - Check black and white scale are visible clearly across the screen. See Fig.
  • Page 43 Colour adjustment 180P LCD Go to cover page ZERO CALIBRATION Zero calibration is performed to determine the output of the measuring probe when no light reaches the sensor and to set this as the zero point to which all other measurements are referenced. Zero calibration must be performed after the POWER switch has been set ON brfore taking any measurements.
  • Page 44: Pcba Architecture

    PCBA Architecture 180P LCD Go to cover page Back Forward...
  • Page 45: Power Distribution Flow

    Power Distribution Flow 180P LCD Go to cover page Forward Back...
  • Page 46 Block Diagram Control Panel C.B.A. 180P LCD Go to cover page Copper Side Frame Buffer (1Mx16 SDRAM x3) TMDS receiver SiI161A DDC1 R (A H/V(TMDS) 24LC21 D-Sub (R,G,B) G (A TFT LCD MODULE FORMAT H/V (D-sub) SCALER CONVERSION SyncSlicer SAA6721 Component Side (Discrete) D-sub/DVI select...
  • Page 47 Schematic Diagram (AC adapter) C.B.A for AC adapter 180P LCD Go to cover page Component Side Copper Side 6111 E1 6112 D1 6113 C1 6117 C1 2121 B1 2123 B1 2124 B1 2126 B1 2153 A3 2154 B2 2155 B2 3101 E2 6118 B1 6151 C3 7102 C1 7121 B1 2127 B1 2156 B2 2157 B2...
  • Page 48 Schematic Diagram (DC to DC converter) Schematic Diagram (Video in) 180P LCD Go to cover page 100N/0805 18VCC BAV99 6301 6310 3303 +5V_DSUB BAS32L 6309 2016 10R/PM5/0805 470U/25V/DIP 2022 470U/25V/DIP +5V_DSUB (1000U/25V) BAS32L 10K/PM5/0805 3304 7301 5331 2015 100N/0805 7006 2021 3301 2304...
  • Page 49 Schematic Diagram (RGB Digitizer) Waveforms Waveforms 180P LCD Go to cover page 7401 +3.3V_A +5VD PQ3DZ13 +3.3V_ADC Waveforms for RGB Digitizer 5401 A8 7403-41 BEAD/1206 A1 3312 A2 3313 A3 3314 A7 7403-40 2402 2404 2405 2406 2407 2408 2409 2410 2411 2412...
  • Page 50 Schematic Diagram (Scaling) Waveforms 180P LCD Go to cover page 3619 22R/PM5/ARV241 MA[0..10] MEM_A0 MEM_A1 MEM_A2 BLUE MEM_A3 A16 3215 A17 3216 A25 7631-5 A26 7631-2 A27 7631-15 BIN_B[0..7] GREEN 3620 22R/PM5/ARV241 MEM_A4 GIN_B[0..7] MEM_A5 MEM_A6 RIN_B[0..7] MEM_A7 3621 22R/PM5/ARV241 MEM_A8 BIN_A[0..7] MEM_A9...
  • Page 51 Schematic Diagram (MCU) Waveforms 180P LCD Go to cover page +5VD 7201 2201 2263 100N/0805 1U/0805 A10 7602-4 A11 7403-115 A12 7203-6 A13 7203-7 A14 7203-18 +3.3VD Normal Low 3204 4K7/PM5/ARV241 LM61CIM 2203 2202 Normal Low 10U/16V/RV2 10U/16V/RV2 3217 6201 10K/PM5/0805 7203 BAS32L...
  • Page 52 Schematic Diagram (Power saving) Schematic Diagram (FRAME BUFFER) 180P LCD Go to cover page MD[0..47] +3.3V MD[0..47] MA[0..10] +3.3VM +3.3VM +3.3VM 2901 7651 7652 7653 7901 47U/16V/RV2 SDRAMX16M SDRAMX16M SDRAMX16M SI4435 +3.3VD MD16 MD32 MD17 MD33 MD18 MD34 2902 MD19 MD35 47U/16V/RV2 MD20...
  • Page 53 Schematic Diagram (Control panel) Schematic Diagram (Audio) 180P LCD Go to cover page 1901 B6 1902 B6 1903 C6 1904 C6 1905 D6 1906 D6 1908 B3 1909 E2 1910 C2 2901 C3 3901 B5 FRONT PANEL 3902 B5 3903 C5 SB: 53591 (8x) 3904 D5 PB: 53601...
  • Page 54 Main panel C.B.A. Component position Back to Main panel C.B.A.
  • Page 55 Main panel C.B.A. Back side Back to Main panel C.B.A.
  • Page 56 Main panel C.B.A. Schematic Diagram (TMDS receiver) 180P LCD Go to cover page (SI_HS--> to PLD for Hsync filtering) 3501 47R/PM5/0805 SI_HS SI_VS & SI_HS, for MODE DETECTION 3502 47R/PM5/0805 SI_VS SI_VS & SI_DE, to SAA6721 3503 0R/PM5/0805 SI_DE 3504 0R/PM5/0805 SI_ODCK R_A7...
  • Page 57 Schematic Diagram (TTL to LVDS) 180P LCD Go to cover page +5TTL +5LVDS +5PLL +3.3VD +5VD install one resister 5016 5018 5019 3117 : for Thine & TI BLM21B222SB BLM21B222SB 3016 : for NS BLM21B222SB 3117 3016 7012 0R/PM5/0805 0R/PM5/0805 TxIN4 PAR4 PAR7...
  • Page 58: Audio Panel C.b.a

    Audio Panel C.B.A. 180P LCD Go to cover page Copper Side Component Side 5931 A2 3924 A1 3925 A1 1930 A4 1931 A1 6921 A1 7922 A1 3926 A4 3927 A4 1933 A1 1934 A2 7941 A3 2923 A4 5932 A1 5941 A2 3928 A4 3929 A4...
  • Page 59: Repair Tips

    Repair Tips 180P LCD Go to cover page preferably be equipped with a thermal control (soldering 0. Warning temperature: 225 to 250 C). - The chip, once removed, must never be reused. All ICs and many other semi-conductors are susceptible to electrostatic discharges (ESD).
  • Page 60: Exploded View

    Exploded View 180P LCD Go to cover page 8238 277 06630 3138 154 01280 INVERTER 1063 3138 154 00570 REAR DOOR BASE - TOP 3138 154 00620 USB COVER - W/O USB 3138 154 00600 3138 151 60570 HINGE PIVOT 3138 157 50780 MID-BUCKET ASSY 3138 157 50980...
  • Page 61: Recommended Parts List

    Recommended Parts List 180P LCD Go to cover page PHILIPS 180P Type number: 180P1L/00 Recommended Parts indicated as below, Item Code number Description 3138 156 30060 CARTON 3138 156 30070 FORM SHEET (FRONT) 3138 156 30080 FORM SHEET (BACK) 3138 156 20800 P.E.BAG-ANTI-STAT.
  • Page 62: Spare Parts List

    Spare Parts List 180P LCD Go to cover page Model: 180P1L/00 Item Code number Description Item Code number Description 450 3138 156 30060 CARTON 3138 151 30290 SHIELD-BASE 451 3138 156 30070 FORM SHEET (FRONT) 3138 100 41530 SCREW W/WASHER M3X14...
  • Page 63 Spare Parts List 180P LCD Go to cover page Model: 180P1L/00 Item Code number Description Item Code number Description 2447 2222 590 16641 MLCC 0805 X7R 100N K 50V PM10 2221 2222 590 16641 MLCC 0805 X7R 100N K 50V PM10...
  • Page 64 Spare Parts List 180P LCD Go to cover page Model: 180P1L/00 Item Code number Description Item Code number Description 3002 2322 730 61183 RST SM 0805 RC 11 18K PM5 R 3325 2322 730 61471 RST SM 0805 RC11 470R PM5 R 3011 2322 730 61478 RST SM 0805 RC11 4R7 PM5 3326 2322 730 91002 RST SM 0805 JUMP.
  • Page 65 Spare Parts List 180P LCD Go to cover page Model: 180P1L/00 Item Code number Description Item Code number Description 6322 9332 153 70215 SMD DIODE BAV99 3632 2322 730 61101 RST SM 0805 RC11 100R PM5 R 6324 9339 139 10115 SMD DIODE BAS32L...
  • Page 66 Spare Parts List 180P LCD Go to cover page Model: 180P1L/00 Item Code number Description Item Code number Description 2926 2038 302 50212 POLCAP 100V 100N PM5 2E 2125 2252 325 26104 MU-LAYER CER CAP 50V 100N X7R 2927 2038 302 50212 POLCAP 100V 100N PM5 2E...
  • Page 67 Spare Parts List 180P LCD Go to cover page Model: 180P1L/00 Item Code number Description 8952 3138 168 75830 5P WIRE HARNESS TO AUDIO BD 8157 8238 277 06000 WIRE HARNESS 14CM 8158 3138 178 79880 AC DC LINE WITH COIL...
  • Page 68: General Product Specification

    . TCO 99 . AUDIO SUPPORT . PROVIDE USB HUB (OPTION) . WALL MOUNT KIT (OPTION) . PROTECTIVE COVER (OPTION) 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 69 Test conditions Resolution Brightness Image size 4.4.1 Actual display size 4.4.2 Max. scan size Brightness uniformity Crosstalk White color adjustment 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 70 Display disturbances from external environment Display disturbances to external environment 6.4.1 Reliability Mean time between failures Quality assurance requirements Acceptance test Serviceability 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 71 LCD monitor with max. resolution up to 1280*1024 /75 Hz non-interlaced. 2.0 PRODUCT PROFILE This display monitor unit is a color display monitor enclosed in PHILIPS global styling cabinet which has an integrated tilt and swivel base. 2.1 LCD Type NR.
  • Page 72 : 1.8 M +/- 50 mm (fixed) Connector type : DVI-D male With DDC1/2B pin assignments. Blue connector thumb-operated jack screws 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 73 Data clock 3.2.3 Software control functions via OSD/control OSD (On Screen Display) function (1) Analog interface OSD : Adjustable functions: 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 74 BRIGHTNESS & CONTRAST IMAGE OPTIMIZATION PRODUCT INFORMATION RESET TO FACTORY SETTINGS INPUT SELECTION CLOSE MAIN CONTROLS MOVE SELECTION THEN ok 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 75 RESET TO FACTORY SETTING : return to Factory preset timings and settings. INPUT SELECTION : select digital or analog input 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 76 14.52(832 dots) E ( us ) 0.323 ( 16 dots) 1 ( 40 dots) 0.569 ( 32 dots) 0.563(32 dots) 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 77 0.015 ( 1 lines) 0.016(1 lines) SYNC. H/V + / + + / + - / - POLARITY SEP . SYNC 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 78 0.012 ( 0 line) 0.015 ( 1 line) SYNC. H/V + / + + / + + / + POLARITY SEP . SYNC 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 79 0.028 (2 lines ) 0.672 ( 21 lines ) SYNC. H/V - / - + / + -/ + POLARITY SEP . SYNC 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 80 3.6.2 In accordance with DVI requirement (DDWG digital Visual Interface revision 1.0) use DDC 1/2B and EDID 3.0 structure 2.0 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 81 Note: 1. Screen displays perfect picture at 16 factory preset modes 2. Screen displays visible picture with OSD warning when input modes are other then 32 preset modes 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 82 Measure YA. Then output Pattern 3 and measure YB. the cross talk value : ABS( YA - YB ) X 100% < 1.2 % 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 83 20 feet 40 feet Environmental characteristics The following sections define the interference and susceptibility condition limits that might occur 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 84 - Altitude : 0-12192m - Air pressure : 300-1100 mBAR Note: recommend at 5 to 35C, Humidity less than 60 % 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 85 System MTBF (Excluding the LCD panel and CCFL) : 50,000 hrs CCFL MTBF : 25,000 hrs (50% of original brightness) 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 86 The serviceability of this monitor should fulfill the requirements which are prescribed in UAW-0346 and must be checked with the check list UAT-0361. 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 87 Go to cover page Fig 1: Brightness and Uniformity 40 +/- 5 mm 40 +/- 5 mm Average = 5 points average 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 88 Fig 2: Cross talk pattern Gray level 46 (64 Gray level) Fig 3: Cross talk Pattern Center at Gray level 0 (Black) 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 89 180P LCD Go to cover page SEPARATE SYNC. VIDEO HORIZONTAL VIDEO VERTICAL COMPOSITE SYNC. VIDEO HORIZONTAL FIG-4 TIMING CHART -1 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 90 Go to cover page VIDEO VERTICAL COMPOSITE SYNC. & VIDEO ( SYNC. ON GREEN ) HORIZONTAL VERTICAL FIG-5 TIMING CHART -2 18.1" TFT SXGA LCD CMTR-180P1L TYPE : 180P1L/00C 8639 000 10531 BRAND : PHILIPS 00-05-31 EDWARD CHANG 00-05-31 Forward Back...
  • Page 91: Lg Lcd Panel

    180P LCD 18” LG LCD panel Go to cover page LG TFT LCD PANEL 18” LM181E1-C2MN 8238 277 02131 Polarizer 9965 000 05077 upper CCFT (upper) 9965 000 05078 lower 9965 000 05080 PWB-A Gate driver 9965 000 05072 Tab-IC Gate Drive (under PWB) 9965 000 05076...
  • Page 92: Inverter Schematic Diagram (I)

    Inverter Schematic Diagram (I) 180P LCD Go to cover page Back Forward...
  • Page 93: Inverter Schematic Diagram (Ii)

    Inverter Schematic Diagram (II) 180P LCD Go to cover page Back Forward...
  • Page 94: Inverter Panel Cba

    Inverter panel CBA 180P LCD Go to cover page Back Forward...
  • Page 95: Recommended Parts List For Inverter

    Recommended Parts List for inverter 180P LCD Go to cover page Description Category Maker's P/N Service code SMD FUSE 3A 32V FUSE 277013090 9965 000 06229 SMD C.C 0603 0.1uF 16V X7R K CAPACITOR 226A21045 9965 000 06230 SMD C.C 1206 470PF 2KV X7R K CAPACITOR 226AB4713 9965 000 06231...
  • Page 96 Parts List for inverter 180P LCD Go to cover page ITEM NUMBER DESCRIPTION PHILIPS service codes R1,R4,R18,R40,R41,R54 211121002 SMD RES 0603 10K 211105610 SMD RES 1206 560 1 % 211220473 SMD RES 0603 47K R11,R68,C6,C7 211220000 SMD RES 0603 0...
  • Page 97 Parta List for inverter 180P LCD Go to cover page ITEM NUMBER DESCRIPTION PHILIPS service codes 226A34725 226B24725 SMD C.C 0603 0.0047uF C13,C31,C40 226D24725 16V X7R K 226E24725 226F24725 226AB4713 226BB4713 SMD C.C 1206 470PF 2KV C27,C28,C38,C39 226DB4713 X7R K...
  • Page 98 X-radiation emissions. For continued X-radiation protection, the replacement periodically against a reference standard. tube must be the same type as the original, including suffix letter,or a Philips 4. When the HV circuitry isoperating properly there is no possibility of an x- approved tupe.

Table of Contents