Table of Contents
Advertisement
Quick Links
U S E R M A N U A L
H E A V Y - D U T Y
M E AT S L I C E R S
#9801614
#9801614
CONFORMS TO UL STD. 763
# 3 4 8 S L M 1 2 • 1 2 " M a n u a l
CONFORMS TO CSA C.22.2
CONFORMS TO NSF 8
# 3 4 8 S L M 1 3 • 1 3 " M a n u a l
# 3 4 8 S L A 1 3 • 1 3 " A u t o m a t i c
# 3 4 8 S L A 1 3 S • 1 3 " A u t o m a t i c w / S c a l e & S l i c e C o u n t e r
w w w. E s t e l l a E q u i p m e n t . c o m
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Estella 348SLM12
Summary of Contents for Estella 348SLM12
- Page 1 U S E R M A N U A L H E A V Y - D U T Y M E AT S L I C E R S #9801614 #9801614 CONFORMS TO UL STD. 763 # 3 4 8 S L M 1 2 • 1 2 " M a n u a l CONFORMS TO CSA C.22.2 CONFORMS TO NSF 8 # 3 4 8 S L M 1 3 •...
-
Page 2: Table Of Contents
I N T R O D U C T I O N Congratulations on your purchase of Estella Equipment. Estella Equipment takes pride in the design and quality of our products. When used as intended and with proper care and maintenance, you will experience years of reliable operation from this equipment. -
Page 3: Safety Precautions
U S E R M A N U A L S A F E T Y P R E C A U T I O N S Potential hazard or unsafe practice, which could result in W A R N I N G serious injury or death. - Page 4 U S E R M A N U A L S A F E T Y P R E C A U T I O N S The following safety precautions must be observed when using this product: Read the relevant instructions carefully before using this product. DO NOT share the same power source with other high-power appliances to avoid excessive power load and other dangers.
-
Page 5: Parts Details
U S E R M A N U A L PA R T S D E TA I L S SHARPENER HANDGRIP BL ADE PROTECTION RING SHARPENER BL ADE COVER BL ADE FENCE PL ATE THICKNESS GAUGE PL ATE PRODUCT PUSHER PRODUCT HOPPER CONTROLS STEM... -
Page 6: Installation
U S E R M A N U A L I N S TA L L A T I O N Remove straps from packaging and remove the Fig. 1 cardboard box. Position the pallet, with the slicer, on a flat surface and remove the Cap (A) from the slicer. -
Page 7: Controls
U S E R M A N U A L C O N T R O L S 348SLM12 & 348SLM13 BL ADE ON BUTTON CARRIAGE PUSHER HANDLE BL ADE STOP BUTTON THICKNESS SELECTION KNOB 348SLA13 BL ADE ON BUTTON... - Page 8 U S E R M A N U A L C O N T R O L S 348SLA13S - FRONT MANUAL CARRIAGE PUSHER HANDLE SCALE ON/OFF BUTTON THICKNESS SCALE DISPL AY SCREEN SELECTION KNOB CARRIAGE SPEED CONTROL KNOB SCALE TARE BUTTON 348SLA13S - SLICE COUNTER CONTROL PANEL SLICE COUNTER DISPL AY...
-
Page 9: Preliminary Checks
U S E R M A N U A L P R E L I M I N A R Y C H E C K S Manual Operation Mode Fig. 6 Ensure the product holding plate is locked. Unlock the carriage by turning the knob to position A. (Fig. 6) Check that the carriage slides freely on the rails. -
Page 10: Operation
U S E R M A N U A L O P E R AT I O N WARNING: Before loading product, ensure the Fig. 11 graduated hand grip is set to "0" and the motor is completely stopped. Be very careful around the blade when loading. - Page 11 U S E R M A N U A L O P E R AT I O N Manual Slicing Fig. 12 Complete Product Loading instructions. Note: DO NOT operate slicer without product in the hopper. Unlock the carriage by turning the lever clockwise. (Fig.
- Page 12 U S E R M A N U A L O P E R AT I O N Automatic Slicing Fig. 14 Complete Product Loading instructions. Note: DO NOT operate slicer without product in the hopper. Lock the carriage by turning the lever counterclockwise.
-
Page 13: Blade Sharpening
U S E R M A N U A L B L A D E S H A R P E N I N G Disconnect the plug from the socket and carefully Fig. 14 clean the blade with denatured alcohol to remove any grease build-up. -
Page 14: Cleaning
U S E R M A N U A L C L E A N I N G • The slicer must be cleaned at least once a day, more frequently if necessary. • All the parts of the slicer that come into direct or indirect contact with food product must be thoroughly cleaned. - Page 15 U S E R M A N U A L C L E A N I N G Cleaning the Sliceguard Fig. 21 Disconnect the plug from the main power supply. Grasp the hand grip (Fig. 21A) and pull up so the (2) pins (Fig.
-
Page 16: Maintenance
U S E R M A N U A L M A I N T E N A N C E Before Maintenance • Disconnect the plug from the main power supply. • Turn the thickness selection knob to "0." •... -
Page 17: Troubleshooting
U S E R M A N U A L T R O U B L E S H O O T I N G ISSUE SOLUTION Check that the power plug is correctly plugged in. Check that there is voltage from the electrical network. Pressing the START button Check that the blade cover is properly closed.
Need help?
Do you have a question about the 348SLM12 and is the answer not in the manual?
Questions and answers