Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-TMG4B1
Summary of Contents for HIKVISION DS-TMG4B1
- Page 1 Barrier Gate User Manual...
- Page 2 WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,...
- Page 3 Barrier Gate User Manual YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
- Page 4 Barrier Gate User Manual Regulatory information FCC information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
- Page 5 Barrier Gate User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text. Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
- Page 6 Barrier Gate User Manual Keep the device away from magnetic interference. Avoid device installation on vibratory surface or places, and avoid equipment installation on vibratory surface or places subject to shock (ignorance may cause device damage). DO NOT touch the heat dissipation component to avoid burns. ...
-
Page 7: Table Of Contents
Barrier Gate User Manual Table of Contents CHAPTER 1 INTRODUCTION ......................7 ......................7 RODUCT NTRODUCTION ..........................7 EATURE 1.2.1 Mechanical Feature ....................7 1.2.2 Electrical Feature ......................7 1.2.3 Safety Feature ......................8 ........................... 8 ACKING ..........................8 IRECTION ......................... -
Page 8: Chapter 1 Introduction
Barrier Gate User Manual Chapter 1 Introduction 1.1 Product Introduction Barrier gate is the entrance and exit management device to limit motor vehicle passing. It can control the boom pole automatically via parking lot management system. Or you can control the boom pole via buttons on remote controller. -
Page 9: Safety Feature
Barrier Gate User Manual 1.2.3 Safety Feature Resistance rebound. If the boom pole is resistant during falling, it can rebound automatically. Induction anti-collision. When the boom pole is falling while the induction signal is received, the boom pole will rise automatically and keep rising during the triggering process. After the induction signal restores, the boom pole will fall automatically to guarantee safety. -
Page 10: Safety Instruction
Barrier Gate User Manual Figure 1-1 Boom Pole Direction 1.5 Safety Instruction Conform to the following instructions for your safety. DO NOT open the host door or cover when the device is working. The internal wiring of the device has been completed when leaving factory. In normal conditions, DO NOT change the wiring. -
Page 11: Chapter 2 Internal Structure
Barrier Gate User Manual Chapter 2 Internal Structure 2.1 Internal Structure Overview The internal structure of the barrier gate host is run by the worm and gear transmission deceleration asynchronous motor. The movement is transmitted to the main shaft via four-bar linkage mechanism. - Page 12 Barrier Gate User Manual Figure 2-2 Machine Core Structure There are extension springs installed inside the barrier gate host. During installation and debug, you can adjust the diameter and quantity of the springs according to the length of the boom pole to reach the moment balance.
- Page 13 Barrier Gate User Manual boom pole/Curved 3 m ≤ L ＜ 3.5 2 × φ 4.5 boom pole 3.5 m ≤ L ≤ 4 m 2 × φ 4.5 4 m ＜ L ＜ 2 × φ 5.5 5 m ≤ L ≤ 6 m 2 ×...
-
Page 14: Chapter 3 Wiring
Barrier Gate User Manual Chapter 3 Wiring Refer to the figure below for the wiring of barrier gate. Figure 3-1 Wiring... -
Page 15: Chapter 4 Dimension
Barrier Gate User Manual Chapter 4 Dimension Refer to the figure below for the dimension of the barrier gate with non-telescopic straight boom pole. Figure 4-1 Dimension For the barrier gate with telescopic straight boom pole or curved boom pole, the dimensions of the host and base are the same as above. -
Page 16: Chapter 5 Barrier Gate Component
Barrier Gate User Manual Chapter 5 Barrier Gate Component 5.1 Barrier Gate with Straight Boom Pole Refer to the figure and table below for the component description of the barrier gate with straight boom pole. Figure 5-1 Barrier Gate Component (1) -
Page 17: Barrier Gate With Curved Boom Pole
Barrier Gate User Manual Table 5-1 Barrier Gate Component Description (1) No. Name Quantity Barrier gate host Boom pole Cross recessed pan head screw M3 × 8 1 Boom pole mounting housing Hexagon head bolt M8 × 65 Flat washer φ 8 Boom pole mounting cushion block Main shaft mounting Hexagon check nut M8... - Page 18 Barrier Gate User Manual Table 5-2 Barrier Gate Component Description (2) No. Name Quantity Barrier gate host Boom pole Cross recessed pan head screw M3 × 8 1 Boom pole mounting housing Hexagon head bolt M8 × 65 Flat washer φ 8 Boom pole mounting cushion block Main shaft mounting Hexagon check nut M8...
-
Page 19: Chapter 6 Installation
Barrier Gate User Manual Chapter 6 Installation 6.1 Installation Description Cut off power before installation. Open the package, and check the accessories according to the accessory checklist. Confirm the installation position of the barrier gate host according to the boom pole direction and the actual condition of the installation site. -
Page 20: Installation Debug
Barrier Gate User Manual The drill size should be matched with the attached expansion screw, and the hole depth should meet the requirement of the expansion screw length. 3) Put the host on the pre-confirmed position. Punch expansion screws into the bottom holes and fasten them firmly. -
Page 21: Chapter 7 Remote Control
Barrier Gate User Manual Chapter 7 Remote Control 7.1 Button Description The buttons are on the lower right corner of the control board. Figure 7-1 Buttons 7.1.1 Independent Button Rise: To control the boom pole to rise. Hold it and the boom pole will not fall. ... -
Page 22: Dip Switch Description
Barrier Gate User Manual Stop + Rise + Fall: Press them to switch between hall limit position and angle sensor limit position. If angle sensor limit position is applied, the boom pole has resistance rebound function. 7.2 Dip Switch Description The dip switch is shown as below. -
Page 23: Remote Control Debug
Barrier Gate User Manual frequency of 0.1 s after the boom pole rises to the limit. Until the boom pole falls to the limit, the status indicator will flash in the frequency of 0.5 s. When the delayed boom pole falling is disabled, the status indicator will flash in the frequency of 0.5 s. - Page 24 Barrier Gate User Manual ensure the motor can run for more than 0.3 s. In angle sensor mode, if exception occurs and the device needs to learn the limit positions again, auto learning must be done firstly.
-
Page 25: Chapter 8 Maintenance
Barrier Gate User Manual Chapter 8 Maintenance Clear the dirt on the barrier gate surface regularly to keep it clean. Check if the fasteners of the device are loose or lost once every month. Fasten them in time. ... - Page 26 Barrier Gate User Manual UD18756B-A...
Need help?
Do you have a question about the DS-TMG4B1 and is the answer not in the manual?
Questions and answers