Table of Contents
Advertisement
5.4.4 ROTATION SPEED OF THE RGB COLOURS
This function allows for varying the rotation speed of the RGB LED strip
colours. To activate rotation of the colours, refer to the "COMMANDS
FROM THE TRANSMITTER" chapter.
5.4.4.1
Setting through memorised transmitters
To do this ("Figure 17"):
1.
press PRG once on the transmitter. The paired LED strip will flash
twice
2.
press PRG once on the transmitter. The paired LED strip will flash
twice
3.
press
q
for 3 s. The paired LED strip will flash three times. Release
q
4.
press
q
(several rimes) until you select the desired option among
those available in "Table 5". The paired LED strip will show the
selected behaviour after a short while
5.
press
o
for 3 s to confirm the choice and exit the function. The
paired LED strip will flash three times. Release
17
1
(x 1)
PRG
x 2
3
(= 3s)
x 3
5
(3s)
ROTATION SPEED OF THE RGB COLOURS
No. of button presses
q
(x 1)
q
(x 2)
q
(x 3)
o
.
2
3
(x 1)
PRG
x 2
4
5
(x ...)
=
...
(x ...)
End
x 3
Table 5
Setting
Speed 1 RGB (factory setting: 4
s - 1 s)
Speed 2 RGB (16 s - 6 s)
Speed 3 RGB (28 s - 10 s)
6
COMMANDS FROM THE TRANSMITTER
6
COMMANDS FROM THE TRANSMITTER
The table shown below summarises the keys to be pressed on the trans-
mitter for sending the main commands to the system.
COMMANDS FROM THE TRANSMITTER WITH SETTING OF PRE-DEFINED
COLOURS (PRESET)
Buttons
Channel activated
Lighting up at the last colour set
p
(x 1)
Increase of the light intensity
p
(> 1 s)
- Stops rotation if colour rotation is under way
o
- Colour selection
Decrease of the light intensity
q
(> 1 s)
q
Switch-off
(x 1)
Clockwise colour rotation
o
p
+
Anti-clockwise colour rotation
o
+
q
SLIDER +
Increase of the light intensity
SLIDER -
Decrease of the light intensity
COMMANDS FROM THE TRANSMITTER WITH SETTING OF PERSONALISED
COLOURS (CUSTOM)
Buttons
Channel activated
Lighting up at the custom colour for that channel
p
(x 1)
Increase of the light intensity
p
(> 1 s)
- Stops rotation if colour rotation is under way
- Selection of the personalised colour for that channel
o
- Anti-clockwise rotation of the colours if no
personalised colour has been set for that channel
Decrease of the light intensity
q
(> 1 s)
- Switching off if the command arrives from the same
channel
q
(x 1)
- If the command arrives from another channel it
switches it on
Clockwise colour rotation
o
+
p
Anti-clockwise colour rotation
o
q
+
Saving of the "custom" colour (the LED strip will flash
p
q
+
three times to confirm the memorisation)
SLIDER +
Increase of the light intensity
SLIDER -
Decrease of the light intensity
7
TESTING AND COMMISSIONING
7
TESTING AND COMMISSIONING
These are the most important phases of the automation set-up for max-
imising the system's safety. The testing procedure can also be used to
periodically check the devices making up the system.
The sequence of steps to be performed when running the testing phase,
as described below, refers to a typical system.
To run the test:
1.
verify that all the instructions stated in the "GENERAL SAFETY
WARNINGS AND PRECAUTIONS" chapter have been strictly
observed
2.
using the control devices (transmitter), switch the LED strips on and
off to test them and verify that they behave according to their set
programme.
Table 6
Table 7
ENGLISH – 9
Advertisement
Table of Contents
